All-wheel drive all-terrain vehicle drawings
Dear visitors to the “ Samodelkin Friend ” website, we present to your attention drawings of the all-wheel drive all-terrain vehicle “Mopets” as well as step-by-step photos of the assembly of a homemade two-wheeled all-terrain vehicle. The Mopets was assembled in St. Petersburg by one of the local Kulibins, American samples of all-wheel drive all-wheel drive vehicles of the “Rokon” type were taken as a basis. A drawing was previously developed and drawn up (see below) and its own all-terrain vehicle was assembled on its basis.
The homemade frame is welded from a square section profile, a 6.5 l/s gasoline internal combustion engine from a walk-behind tractor, all-wheel drive on the front and rear wheels, torque transmission is carried out through a chain drive. The suspension is rigid without shock absorption, ATV wheels are 25 inches.
The all-terrain vehicle is designed to overcome off-road, rough terrain, as well as wetlands and forest areas. Mainly actively used by fishermen and hunters.
And so, let's carefully look at the presented drawings, as well as step-by-step photos of assembling the all-terrain vehicle based on them.
Materials
Tools
Drawings of an all-terrain vehicle and step-by-step photos of do-it-yourself assembly. Assembling an all-terrain vehicle according to drawings.
Adjusting the angle of the front fork and the fracture unit.
Frame
Slave stars
Fracture node
An all-terrain vehicle sneaks through the swamp)
We also invite you to familiarize yourself with a similar all-terrain vehicle of the VASYUGAN type and there is also a more interesting design with the transmission of torque to the front wheel through a cardan drive, you can find it HERE Stay tuned for many more interesting things to come;)
Boat motor from a screwdriver
Look at the design of a homemade boat motor from a screwdriver in the photo below.
As you can see, it is assembled from very simple parts - pins, boards, ties, the only rarely used part is an angular gearbox for changing the vertical rotation from a screwdriver to the horizontal rotation of a screw.
Watch the video of testing such a boat propulsion unit.
The speed is, of course, less than that of a boat motor from a gas trimmer, but operating an electric motor is several orders of magnitude cheaper.
Firstly, you can connect a small 12 Volt battery from a motorcycle, this will give you an energy reserve for 6-8 hours of engine operation.
Secondly, the cost of electricity is very low compared to gasoline. Let's remember the Tesla electric car - its range of 250 kilometers costs the owner 150 rubles spent on charging the batteries, but how much gasoline does a sports car with the same speed characteristics consume?
To increase speed, you can install a propeller with a larger pitch.
For ease of control, place the handle like a regular outboard motor with a gas handle; see how to do this with your own hands in the video below.
As you can see, a homemade outboard motor is a fairly simple thing that you can make yourself.
To conclude the topic, all that remains is to add that during long-term operation it is necessary to equip the propeller with a protection and a heel, the latter will help preserve the propeller when touching a rocky bottom, and the protection will not allow the propeller to chop up debris floating on the surface.
Stas comments:
This trimmer will quickly be reworked because it does not have water cooling, but only air. Judge for yourself soon he will be karachun.
Artem comments:
Who cares? The trimmer plows all day long without any problems, I mowed 40 hectares with it (I'm tired of it). And such alterations are driven around Ukraine in vain - they die from wear and tear, but are restored by major repairs with rings.
Valera comments:
a screwdriver would be more likely to work here, since it is not intended for long-term work and heats up very quickly
Artem comments:
We rode on a motor made of no mows. Norm is rushing on an inflatable!
Igor comments:
just add a motor
ttt comments:
It just rattles like a tractor.
Peter comments:
Good afternoon. I am planning to buy a Haswing Osapian electric motor for fishing of this model: https:// What can you say about this company? Has anyone dealt with them, do they break badly and do they need to be serviced somehow? Thank you!
Sergey comments:
If you understand that your need is charitable assistance, then pay attention to this article. Those who, without your participation, may lose an exciting business have turned to you for help. Many children, boys and girls, dream of becoming pilots on the track. They attend classes where, under the guidance of an experienced trainer, they learn high-speed driving techniques. Only constant exercises allow you to overtake correctly, build a trajectory and choose speed. Winning on the track is based on good qualification. And, of course, a professional kart. Children who participate in clubs are completely dependent on adults, because lack of money and broken spare parts do not allow them to participate in competitions. How much pleasure and new sensations children experience when they get behind the wheel and start driving the car. Maybe it is in such a circle that not only Russian champions grow up, but even future world champions in this sport?! You can help the children's karting section, which is located in the city of Syzran. They are in a really bad situation right now. Everything rests on the enthusiasm of the leader: Sergei Krasnov. Read my letter and look at the photos. Pay attention to the passion with which my students work. They love this developmental sport and really want to continue learning. I am asking you to help the karting section in the city of Syzran survive. Previously, there were TWO young technician stations in the city, and each had a karting section. There was also karting at the Palace of Pioneers. Now there is not a single station in the city, and the circle in the Palace of Pioneers was also destroyed. They closed it, I can’t say enough, they just destroyed it! We fought, wrote letters, and everywhere they had the same answer. About five years ago I went to the governor of the Samara region for a reception. He didn’t accept me, but my deputy accepted me. After that, we were given premises where we were based. We have a lot of children who want to go karting, but very poor material conditions do not allow us to recruit children. And most of the karts require repairs. This is the situation our circle is in. We also turned to the mayor of the city of Syzran for help. This is the second year we have been waiting for help. We decided to turn to you via the Internet for help. Contact me, ADDRESS FOR PACKAGES, 446012 Samarskaya, 47, you can contact me through social networks SERGEY IVANOVICH write by email Always, being on a wave of success, you need to do works of mercy, give alms. And if the Lord helps in difficult circumstances, then do not forget about gratitude afterwards. Then He will not forget about your needs.
2x2 drawings
The basis of an all-terrain vehicle (or ATV) is a frame made of pipes or a square profile. The power plant is suitable from a walk-behind tractor (6.5-7.5 hp). The drive is often done on the rear wheel (sometimes on 2), it rotates using a chain drive.
The suspension is configured without shock absorbers, the wheels have a diameter of 20-25 inches.
Having decided on the basic parameters, they draw sketches, check all the dimensions again, and make calculations. After this, drawings are prepared, sometimes existing samples are taken as a basis, altering them to suit your needs.
ATVs designed on the basis of the Ural motorcycle
At the moment, several decades ago, the popular domestic Urals in Russia have been replaced by much more nimble and economical foreign models.
In this regard, many people have their recent best “friend” standing idle and rotting in their garages. But not a single Russian person is able to allow good things to go to waste. Therefore, “Urals” are increasingly used to create a type of transport that is relatively new for Russian people. This motorcycle is unanimously recognized by folk craftsmen as the optimal basis for creating an ATV. Homemade ATVs made from it are an order of magnitude more economical and have greater draft power than their factory-made counterparts. The creation of an ATV based on the Ural consists of two stages: designing the rear part and the front. The use of the Ural gearbox when creating the rear part of the ATV will ensure the design not only strength, lightness, but also simplicity. In the end, the finished product will not be equipped with a differential, which, in essence, can be sacrificed in the name of reducing the time spent on its creation. As for the design of the front part of the future vehicle, it will take much more effort and time than the previous stage. Most of the work is finishing up the front arms of the ATV. This is due to the fact that they should be less rigid than a car, but more powerful than a motorcycle.
Manufacturing instructions
When assembling a 2x2 all-terrain vehicle, you must pay attention to ensure that all elements fit together.
If there is play in some components, the machine will fail in a short time. The power plant, fuel tank, drive, wheels are taken from a motorcycle or car.
The unit can be assembled relatively inexpensively using used spare parts from the domestic auto industry; it is better to install a new brake system. If travel will take place on paved roads, the design can be made lighter by installing a low-power engine. A large trunk made of pipes is sometimes installed on the frame.
Source
Homemade boat motor from a trimmer
A gas trimmer is a very successful tool for converting into a boat engine.
See for yourself - it has almost everything you need - an internal combustion engine, a rod with a shaft transmitting torsion and an angular gearbox. All that remains is to equip the trimmer with a suspension on the transom, change the throttle control handle and install the water propeller.
The petrol trimmer is equipped with a centrifugal clutch, so the screw will not rotate at low speeds.
Here is a video of testing such a modification.
As you can see, a homemade boat motor from a gas mower does its job perfectly.
You can also use the electric version of the trimmer for mowing grass, but there will be more alterations with it, there is a 220-volt electric motor and you will have to install a board for converting 12 volts from the battery to 220. Such a board can be taken from an old uninterruptible power supply from a computer.
If we are already talking about electric motors, then it is worth remembering screwdrivers - the engine on them is quite powerful, so it is quite suitable for use on a homemade boat.
