How to make a basketball court at your dacha with your own hands

What dimensions can a homemade shield have?

For yard basketball, it is not necessary to follow standard parameters. It is not so important what size basketball backboard you have, the main thing is that its field can accommodate a square for throwing the ball, which, as mentioned above, is 45 x 59 centimeters in size. The ring itself, with a diameter of 45 cm, can be easily bent from a tube or rod. It is attached to a metal corner with bolts or welding. The dimensions of the fasteners themselves are not so important; only a 15-centimeter distance between the ring and the shield should be maintained.

Results

Which ring is better, homemade or purchased? There is no clear answer here. A homemade product performs sporting functions and is aesthetically pleasing to family members and friends of the manufacturer.

Even if outwardly it is a little more unsightly than store-bought. In addition, homemade is designed for certain loads . Whereas a store-bought product, it is unknown how long it will sag under harsh conditions.

On the other hand, a high-quality, expensive ring with a shield, produced at the factory in compliance with all sizes and GOST standards , handmade, is unique. So it’s up to the players to choose.

Setting up a basketball corner

Already when the foundation was just being installed, we should have thought about where our ring would hang. For convenience, racks with rings are installed along the edges of the site, as in a real gym. Here are the dimensions that must be observed:

• The minimum distance between posts is 3 meters.
• The field area should be approximately 20x35 m.
• The ring itself should be located approximately 2 m from the ground.

Making a shield

Making a basketball hoop with your own hands, like a backboard for it, is not at all difficult. To make a shield yourself, we just need to adhere to the following algorithm:

1. Make a frame from metal corners that need to be welded together to the specified dimensions.
2. Select the necessary boards to make the wall. When they are fastened together, there may be some gaps left, but they will not interfere with the game at all. Just make sure that the boards are level.
3. Next, the manufactured shield needs to be painted to your liking. You can involve children in this procedure, because they are known to be the best designers.

We make the main component

Here we will look at the classic wicker version and learn how to make a basketball hoop with your own hands. In general, it’s not that difficult to make, the main thing is to show a little accuracy and desire.

To create wicker rings, summer residents will need only two things:

• The base of the ring. Typically it should be made of iron.
• Strong threads. They can be noticed: thin rope, cords, thick yarn, any rope.

So, what needs to be done in order for its main component to appear on your site:

Manufacturers and the cost of their products

Chinese with many years of experience offers quality equipment:

• mobile stands with a basket and a shield of various sizes costing from 10,500 rubles;
• basketball hoops without a net - 700 rubles;
• basketball farms from RUR 26,000;
• figured laminated shields - 22,000 rubles.

The Ukrainian company sells a protective shield with a ring 46 cm in diameter and a neoprene mesh at a price of 5,500 rubles.

Russian produces sports equipment for basketball courts:

• a board made of moisture-resistant plywood and a metal base has a price of 15,000 rubles;
• a ring with a mesh can be purchased for 600 rubles.

Find out how to make a birdhouse with your own hands here.

How to install outdoors at home

At home, like any construction, laying a sports complex requires drawing up a work project at the beginning. And then an approximate estimate. After all, if at the time of laying there are not enough funds, it is necessary to calculate the work plan in such a way as to make do with the available funds in the first stages. First, you should level the area and cover it with a suitable covering. It can be laid both on the ground and on concrete.

You will find all the information about rubber coatings for playgrounds in the country in this material.

Foundation installation

Installing a flat cement surface involves the following work:

• removal of fertile soil layer. It is necessary to dig up 40 cm of soil, first removing a layer of grass and then a small layer of soil. This is necessary to lay a drainage cushion before laying the main covering;
• then geotextiles are laid on the soil. It comes as a single piece, so you must first cut it to size into separate pieces that can be laid both horizontally and vertically. The main thing is that they overlap each other by at least 30 cm. This will prevent subsidence of the upper drainage layer. Sand should be poured onto it and leveled; the approximate thickness of this layer should be 15 cm;
• a geogrid is laid, which will serve to strengthen the entire structure. It is made in the form of cells, which are half filled with sand and covered with crushed stone on top. Using special tools, the latter is compacted to a thickness of 15 cm;
• pouring cement in several stages, this is necessary to create expansion joints. With their help, the top coating will be permanently fixed on the cement plane, and moisture will pass through them faster.

If you still decide to lay the main surface of the sports ground on the ground, then you should remove a small layer of grass from the laying site and fill it with sand, not reaching the edges in height.

Read also: MTS support service

Original roofing and designer roofs

Today we will talk about how to make a high-quality basketball backboard and a basketball net with your own hands at home from scrap materials.

We will also consider manufacturing technologies for basketball backboards and nets for playing basketball for children or adults.

In order to make a simple basketball hoop for children with our own hands, we will need thick wire and also rope.

Instead of thick wire, you can take an old unused hula hoop, cut it, shorten it and connect it again. It is important to leave a “shoot” for attaching the ring to the shield.

If you want to make a basketball hoop with your own hands from thick wire, then in order to get the most even circle, we recommend using a cylindrical device designed to serve as a template. We wind the wire around it. And don’t forget to leave an “appendage” for attaching the resulting ring to the basketball backboard.

The diameter of the metal blank for the ring should be slightly larger than the diameter of the basketball. Then you should take the prepared rope and cut it into 20-22 identical pieces. In this case, the length of each should be 2.5 - 3 times greater than the planned length of the mesh overhang.

These segments are attached to a metal ring at equal distances. You need to tie the ropes exactly in the middle so that 2 ends of equal length remain free. Then we tie in turn 2 ends of nearby ropes around the entire circumference of the ring. This is the first level of our grid. Next, we similarly connect the ropes to the next level, etc. If you want to make a basketball hoop for your home, you can tie the bottom of the net, then the ball will stay inside when it hits. This will help reduce the chance of the sports equipment accidentally bouncing after it hits the basket.

DIY basketball backboard for adults. How to make a professional basketball backboard - you have to try hard. How to make a basketball backboard at home. The process of making a basketball backboard is no more difficult than making predictions for sports, especially if the necessary materials are available.

Here are typical instructions for making a basketball backboard at home. For the base of a basketball backboard, you can choose a sheet of plywood, which is inexpensive and not difficult to get either. A strong rectangular piece of plexiglass or thick plastic may also be quite suitable. If the basketball backboard will be installed outdoors, then you should approach the choice of material for its base based on considerations of not only strength, but also resistance to adverse weather conditions. The next stage is the choice places where the basketball backboard will be attached. When choosing such a place, the main thing to remember is that the lower edge of the shield should be at a height of 290 centimeters from the ground, and the ring should be located at a height of 305 centimeters. Now you need to apply the dimensions and cut a plywood blank according to them. The ideal size of a standard basketball backboard is the following parameters: width – 1.8 meters, height – 1.05 meters. This size will allow players to make more accurate and varied throws. Before you start cutting out the workpiece, you need to use a pencil to outline the dimensions and draw the lines along which the workpiece will be cut. It is better to cut it using a jigsaw, when working with which you must be careful.

After the blank for the future basketball backboard is ready, you will need to draw a white square on it, which plays a very important role.

The white square is a kind of guide for players when shooting; with the help of such markings, getting the ball into the basket is much easier. If the ball is thrown correctly into the corner of this square, then it will definitely reach the goal. In order to mark such a square, you need not only a brush and paint, but also knowledge of the dimensions of the rectangle. Its external dimensions horizontally are 59 centimeters, and vertically 45 centimeters. When marking, it should also be taken into account that the upper edge of the base of this rectangle must coincide with the level of the upper plane of the ring. The width of the square stripes should be 5 centimeters. Basketball hoops Material - durable steel, internal diameter 45 cm and painted orange.

The metal rod of the ring must have a minimum diameter of 16 mm and a maximum of 20 mm. The bottom of the ring should have provisions for securing the nets, such as to prevent finger injuries.

The mesh should be attached to the ring at twelve equally spaced points along the entire perimeter of the ring.

Devices for attaching nets should not have sharp edges or crevices into which a player’s fingers could get caught.

The ring is attached to the structure supporting the basket in such a way that no force applied to the ring is transmitted directly to the backboard. Therefore, there should be no direct contact between the ring and the device securing the ring to the shield and the shield. However, the gap should be small enough that fingers cannot get into it. The top edge of each ring should be located horizontally at a height of 3.05 m above the surface of the site at an equal distance from the vertical edges of the shield. The closest point of the inside of the ring should be located at a distance of 15 cm from the front surface of the shield. You can use rings with shock absorbers. Made of white cord and designed to momentarily hold the ball as it passes through the basket. The length of the mesh must be at least 40 cm and no more than 45 cm. Each mesh must have 12 loops for attaching to the ring. The upper sections of the mesh must be sufficiently rigid to prevent: The mesh from wrapping around the ring and possibly becoming entangled. Getting the ball stuck in the net or being thrown back out of the basket by the net. A basketball net can be woven from braid, twine, rope, or thick threads. The braid or threads are first cut into pieces. The length of each segment should be four times the length of the grid. The number of segments is determined as follows: measure the ring intended for the mesh, and the resulting value is divided by four. The DIY basketball backboard is almost ready. Now it needs to be firmly secured. To do this, you will need 4 large bolts that can withstand a load of 30 kg and drill four holes in the wall or any other place where the basketball backboard will be mounted. To drill holes evenly, use a level. After this, you can begin installing the shield. It is very inconvenient to do this yourself, so you should again resort to the help of friends who can back you up on the stairs, as well as give and hold the shield.

Once the bolts are installed and tightened into place, you can hang up the basket so you can finally play on the court with a new basketball backboard that will last for years.

In short, you can make a good basketball backboard with your own hands. But it is important to pay attention to one serious point. The fact is that no matter how it may seem to us from the outside that the contact of the ball and the basketball hoop is quite soft, it should be noted that the impact load on attaching the hoop to the backboard is very high. The weight of the ball (if we do not go into the definition of physical values) during contact with the ring increases many times, even when throwing from an average distance. Well, with an inaccurate hit from a long distance, this blow can reach destructive force. And such a load acts on the fastening hundreds and thousands of times. So that your work does not go in vain, that is, the future ring with the shield is a reliable design, you need to pay maximum attention to attaching the ring to the shield and then the same shield to the wall or other structure. Regarding the material of the shield, it can be put together from the same inexpensive available pine boards, or better yet from harder wood. Proposals to make a basketball backboard from plywood, fiberboard, and plastic do not stand up to criticism. The first two positions do not work because if your shield hangs for a season in the rain and sun there will be nothing left of it. Plastic will by its nature withstand all these elements of the elements, but is unlikely to be affordable. Plastic is different from plastic, because the one that is used in the gym is very expensive, the other, the other lottery... will withstand it - it won’t withstand it. But a wooden board is a material that has stood up to time and history. It is known that the official dimensions of a basketball backboard are as follows: a width of 1 meter 80 centimeters and a height of 1 meter 5 centimeters. But in principle, you can try to build a flat square from boards 3 cm thick and 80 cm X 80 cm in size, I think this area will be quite enough to play normally or practice a throw. Basically, only the square (its width is 59 centimeters, height 45 centimeters) above the ring is actively used when throwing, since it is this small square that you need to be able to hit if you want to throw from the shield. Then (if it hits this square) the ball will most likely fall into the ring. Even in this case, if you make a throw with a rebound from the backboard, the load on the backboard itself will be very small, but on the fastening of the backboard and the ring, in this case the pressure will be maximum. The basketball hoop is made of a metal rod with a diameter of 16 - 20 millimeters. I think everyone understands that to protect it from precipitation, the entire structure should be painted with appropriate paint, which can be bought in a store, explaining to the seller why the paint is needed.

In the end, I will repeat and say that when trying to make a basketball backboard yourself, pay attention to the attachment of the ring to the backboard. This is the most fragile place in this structure.

Source: https://crovlya-krisha.blogspot.com/p/basket-zit.html

Required materials and tools

To prevent the shield from falling apart after several hits from the ball, you need to use durable wood materials (multi-layer plywood, MDF or fiberboard) or high-quality thick plexiglass to make it.

What else is needed:

• electric jigsaw;
• tape measure, square, long ruler and marking pencil;
• bolts or self-tapping screws and metal brackets for attaching the shield to the support;
• narrow and wide flange brush;
• waterproof paint in red and white;
• sandpaper;
• drill with bit attachment.

How to make a street billboard with your own hands for a summer residence

The basketball backboard is made of very durable, unbreakable glass, which is pre-tempered in a special way. Since such material costs a lot of money, a rectangle made from it turns out to be expensive. If the task is to make your own equipment for the game, then it is not necessary to buy expensive materials.

Materials and tools

In order for the basketball backboard to withstand all the impacts of the ball and not fall apart after a few days, it is necessary to use durable materials made of wood (fibreboard, MDF, multi-layer plywood) or high-quality plexiglass.

You will also need the following tools:

• electric jigsaw;
• sandpaper;
• drill along with an attachment for bits;
• white and red paint, resistant to water;
• flange brush;
• metal brackets for fastening;
• bolts or screws;
• ruler, square, tape measure, marking pencil.

Sawing the workpiece

1. First you need to decide on the dimensions of the workpiece. The standard dimensions of a basketball backboard are 180x105 cm, but for training on the street or in the countryside, 100x80 cm is enough. Based on the parameters, a rectangle is drawn on a sheet of plywood, plexiglass or MDF sheet.
2. On a sheet that is placed on a workbench, the base is cut out using a jigsaw. Act exclusively along the intended lines. The edges are processed with sandpaper.
3. Then a line is drawn parallel to the bottom edge at a distance of 15 centimeters from it. The next step is to find the middle and lay out 29.5 cm long segments from it on both sides.
4. Parallel to the side edges, 45 cm are measured upward. The points that were obtained are the corners of the upper rectangle. They are connected in series.

How to choose a location for a basketball court

It is necessary to approach this responsibly, not to forget that this place for basketball will be constantly used and the ball will be played on it. Therefore, you should immediately choose a site that is located far from the house and garden. Depending on the soil and groundwater, a basketball court cannot be located in the following places:

• near bodies of water - if a ball hits it, ornamental plants in the pond or children playing happily in the pool can be injured;
• on the slopes . All sports fields require a perfectly flat surface for proper play;
• in the lowlands After numerous rainfalls, the sunken area may take a long time to dry, and therefore its use will not last long;
• on a site with nearby groundwater . Changes in soil in the off-season can affect the fastening and fixation of sports equipment - a rack with a basketball basket. It may become warped.

Video

In the video - how to install a basketball hoop at your dacha with your own hands:

A sports corner at the dacha will not only provide active recreation for the whole family, but will also be a good release after a hard day at work. On the basketball court you can play with friends and neighbors, organizing mini-tournaments. This game will appeal to the younger generation, who will ask to go to the dacha with you just for this reason.

You might also be interested in reading about the benefits of an all-weather tennis table for your garden.

: Frame

1. Bend a piece of flat metal, mine was 4mm thick.
2. Weld it to a flat point in the ring.
3. Cut two rods to 320 mm length.
4. Cook them as shown in the photo.
5. Drill four holes to match the size of the bolts you have.
6. If you need a netball hoop, you can simply attach it to the post and skip the rest of the steps.

: Mesh brackets (optional)

Show 7 more images
Do this step if you need a grid. If you need a network, you will have to buy it. This step is not as difficult as it seems.

1. cut 12 pieces of wire 90mm long (I would recommend making some spares as they are easy to ruin.)
2. bend them in the middle (it doesn't matter if the ends are the same length)
3. clamp the wire in a vice with a steel rod at one end
4. bend the wire over the rod
5. repeat this with all parts
6. re-clamp the wire wrapped around the rod (see photo)
7. bend it
8. repeat the action with all parts
9. re-clamp the wire wrapped around the rod
10. bend it (at this stage you won't be able to just remove the wire from the rod - you will need to slide it to one of its edges and remove it from the edge)
11. repeat with all parts
12. divide into 12 parts and weld the staples

Materials and tools for making a shield in the yard

Professional basketball backboards are made of transparent, unbreakable plastic. At home, they use boards on a frame, moisture-resistant plywood and chipboard, OSB and MDF boards. We decided to make a basketball backboard for a children's playground from 16 mm thick plywood. Since the plywood sheet was not of sufficient height, it was built up from below with a board with a section of 25x120 mm. To make a basketball backboard outdoors, you need the following tools and materials:

• brown and white PF paint;
• emery cloth;
• self-tapping screws;
• masking tape 50 mm wide;
• electric drill and jigsaw;
• flat brush;
• roulette:
• square;
• pencil.

: Color the shield

Once you have all the lines drawn on the backboard, place masking tape over them. If you try, everything will look neat.

If you are using MDF, you will need to take care to protect the edges from moisture (as shown in photo 2).

Carefully paint the areas around the masking tape.

Remove the masking tape once you have applied enough coats of paint and the board looks finished.

Making a basketball hoop with a net

The basis for making a homemade ring can be a strip of metal with a cross-section of 40x4 mm, a tube with a diameter of 15-20 mm, or a sports hoop. It is easy to bend the strip using a large diameter object as a mandrel. To bend a regular steel tube, you will need a pipe bender. The easiest way is to cut the desired segment from the hoop and fasten the ends again.

To simplify the task at home, the ends of the ring can be screwed with self-tapping screws to a wooden block, which can easily be secured to the shield. The ring should be painted in several layers of weather-resistant red enamel. Drawings of the ring according to the standard are presented in the following photo.

The mesh on the ring is often considered an unnecessary element. However, it is designed to throw the ball in a certain direction and is necessary for serious play. The mesh can be tied from twine and secured through 12 holes, which must be drilled evenly along the diameter of the ring.

It is more correct to weld a series of wire loops to the ring. As a last resort, pieces of rope can be secured around the perimeter of the ring with loops, and then tied together to form a mesh. For the simplest example of making a mesh with your own hands, see the following video.

: Color the ring

First you need to sand the metal. I used a sanding disc on my grinder.

The ring should not be black or white, it should stand out relative to the shield. Typically the ring is orange or red in color.

The easiest way would be to spray paint the equipment.