How to make a cardboard barrel with your own hands. Making a beer keg

Making a barrel of honey from cardboard

I present to your attention a master class on creating a barrel from cardboard.

1. Using a glue gun, I glued strips of cardboard to the rim, having previously rounded them off.
2. I attached cardboard strips in the shape of a lid to tape.
3. She rolled a tube out of newspaper and twisted it in a circle.
4. I connected it and got a handle for the barrel lid.
5. I glued two tubes of newspaper around the perimeter of the barrel.
6. Inside I covered everything with pieces of thick paper.
7. I covered the outside with paper napkins.
8. I cut out and glued letters from cardboard.
9. I glued decorative pearls.
10. Covered the outside with putty.
11. I covered everything with a final layer of acrylic varnish and painted it with acrylic paint.

Making a miniature of an antique barrel

To make this miniature, we will need a very ordinary shovel handle with a diameter of 27mm, a small piece of leather measuring 10cm * 5cm, wooden toothpicks, a wooden block measuring 3cm * 3cm * 2cm, stain, varnish.

You will also need everything that is shown in the photo below.

To begin, cut off a 38 mm long piece from the cutting.

Then the cylinder needs to be processed with a stationery knife on both ends, giving it a sloping shape.

Be careful with the utility knife blade to avoid injury!

Now, using sandpaper wrapped around a small wooden block, we process the entire surface of our workpiece, achieving a smooth surface of the product.

Next, using a pencil, we draw the lines of future joints of the staves (boards) of our barrel.

After this, using a triangular file (small file), we saw through one of its corners along the lines drawn with a pencil, giving our barrel a relief.

Now you need to cut out the sweet clover from both ends of the barrel. To do this you will need a set of wood cutters.

First, we draw circles from the ends of the product, retreating 1.5 mm from the edge.

We draw a grid in this circle. Then use a semicircular cutter to press a 1 mm indentation along the circumference line.

Next, using cone-shaped cutters, we make slits, duplicating the drawn mesh.

We do this to make it easier to remove the top layer of wood inside the circle.

Now with the same cutters we remove the same top layer that is indicated above.

Be careful not to cut off the edge of the rivets!

Just in case, I want to post a photo of a set of cutters that it is advisable to have for work.

After the sweet clovers are completed, you will need to extend the slots between the rivets from the edges of the barrel to the sweet clovers.

To do this, you will need the same triangular needle file that was used earlier.

Then you need to sand the entire product.

We mark with an awl the places of future traffic jams. The filler should be located in the middle of one of the rivets, and the drain should be turned 180 degrees relative to the filler and located on the clover.

Now we drill holes 2-3mm deep in these marks.

Next we need to cut small cylinders from our toothpick to make the plugs. The length of the cylinders should be 1 mm greater than the depth of the holes so that the plugs stick out slightly.

Glue the corks into the holes, but if they fit tightly, you don’t have to glue them in, because the varnish will subsequently hold them securely.

What can be made from boxes - a barrel, a chest for storing threads

DIY pig feeder

When you think about what you can make from cardboard boxes, pay attention to the following masterpiece. If you have a thick corrugated box from household appliances, then it will work perfectly

You will need to disassemble it, then you can start crafting.

This barrel consists of three containers. See how to create each one. To do this, you need to cut out a circle and a narrow rectangle of the required diameter.

Notice how you then glue the triangle to the circle to create a seamless connection

To do this, remove the strip of cardboard at the bottom, align the two sides of the rectangle, and then place the remaining thin strip of cardboard on top.

Then take the same material and cut a small strip from it. She will become a pen. You will need to make two of these things to glue them opposite each other on the outside. Pre-fold the strips so that they resemble handles.

See why these elements are needed. When you make several trays like this, you will put this kind of fastener here. Its fixed parts will help connect the handles, and you will tilt the sliding parts down when you need to get one of the containers.

To ensure that the containers fit well together when you decorate each container, make an additional narrow bottom. Then one container will fit well into the other.

Now for such a craft you need to make a lid from cardboard. To do this, cut out a large circle. This will be the basis. In the center, you need to glue a few more, but small, cardboard circles onto it in a stack. They will become comfortable handles.

The sliding mechanism consists of four cardboard parts. Two are equal. They are strips of the same size. You will insert them into the handles of the containers. At the bottom, these strips are connected to a cardboard frame. When necessary, you simply lower it. A handle made of the same material is glued to the top of this frame for convenience and beauty.

Now you can use a fine-tip marker or a regular pencil to create these designs on your work. Or you can cover such boxes with colored paper.

You can put various little things in them. It will be especially convenient to store small sewing supplies here. You can also place small toys, which will no longer be lying around the house, but will be in their places.

And to make a chest for storing thread, you will need a shoe box with a folding top. Mark its bottom to see how far apart the spools of thread will be. Make dots at these places.

Now, from the reverse side, pass the nails of the required height here. It would be nice to additionally fix them using the hot rods of a silicone gun.

To make the thread storage box even more reliable, it is better to additionally glue a rectangle of corrugated cardboard to the bottom, and then fix the nails.

To avoid injury, it is better to first remove the point of the nails and polish it.

Here's what else you can do from a cardboard box.

Take a shoebox and prepare it. To do this, rub the surface of the lid and box with a candle. Bring some white acrylic paint here. Then all that remains is to lightly rub with sandpaper on the folds to give this antique effect.

To make the container look like a suitcase, take pieces of leather and glue them on the corners. Make handles and clasps from leather belts. You can place sewing supplies, toys, and other items inside.

Master class on arts and crafts “A Barrel of Honey”

Structural unit "Prometheus" of the state budgetary educational institution of the Samara region, secondary school No. 2 named after. V. Maskina railway Art. Klyavlino municipal district Klyavlinsky Samara region

Fomina Natalya Konstantinovna

additional education teacher

The master class is intended for additional education teachers, primary school teachers working with children of primary school age.

One of the manifestations of patriotism is love of nature. Every person, regardless of age, should treat nature with care and respect. Love for nature is determined, first of all, by a careful attitude towards it. In order not to pollute it, in my master class I will tell you how you can give a second life to old cardboard boxes.

Waste material provides enormous opportunities for fulfilling fantasies. The most interesting thing is that in this case such material for crafts is at hand. In order to make something fun, you don’t need to go to the store, go to the forest or go to the park and collect natural materials. Everything you need can be found in your household solid waste or in the far dusty corner of your garage. Egg containers, shells, plastic and glass bottles, hard dairy and juice bags and much more make great, free craft materials. In the process of work, children acquire labor skills and abilities, develop creative imagination and constructive thinking, and master ways of working with various tools that are suitable specifically for the material with which they are currently working. Thus, crafts made from waste materials will help your children appreciate every little thing. And the main thing is to include your imagination and imagination regarding how you can use this or that waste material.

Target:

Teach students to work with cardboard boxes and make what they need from what they don’t need.

- contribute to the formation of knowledge about the norms and rules of behavior in nature, develop the need to communicate with nature;

Linden honey barrel

The boards for the barrel are planed and driven through a surface planer. The size of the planks is 20*140 mm. Boards are cut along, not across, the grain. Using a circular saw or miter saw. When cutting, you need to use a protractor, because the cross-section of the planks should be trapezoidal in shape.

Note! The width and number of slats are calculated based on the required barrel size and the thickness of the available material. For example, there may be 12 of them.

Each plank should be sanded to remove any unevenness and wood fibers. Then the planks are laid out in a circle, with the narrow sides inward. They are either glued together or steamed and bent, secured only with hoops. How to glue:

Barrels for honey wholesale and retail - Veles LLC

Honey barrels are in strong demand, don’t stand aside.

Specialization - cooperage and honey barrels . We are pleased to offer you a wide selection of products for honey and its display. Honey barrels are in strong demand, don’t stand aside.

Here are some characteristics of our products:

• made from a typesetting drum;
• the inner surface is treated with beeswax;
• Laser engraving of inscriptions and logos is possible.

The main advantage is that honey barrels ideally preserve all the beneficial qualities of the product and are excellent for storing it. Moreover, in addition to honey, you can also store other products - such as butter and cheeses. You can purchase two types of containers from us:

• 0.3–3 kg, for exhibitions and attracting clients;
• from 15 kg, directly for storage.

There is one more feature of our products - they are made from linden (and not from coniferous trees) and treated with beeswax. This is done so that the honey does not absorb the smell of wood and retains its rich color and taste. By purchasing honey barrels from, you can store the product for many years without any harm.

By the way, they can be used not only for storage - we are happy to offer you options that will be an excellent corporate gift. We can apply laser engraving without any problems and carry out an individual order in the style of your company. Do you want to buy honey barrels from us !? Call!

• More photos

Source: https://bochkiveles.ru/bochonki-dlya-mjoda.html

How to make a bear out of cardboard with your own hands

I present to your attention a step-by-step process for making a moving paper toy “Teddy Bear”. The master class will be useful for primary school teachers, kindergarten teachers, and young parents who have a small child. The baby will find it interesting because the toy’s legs move with the help of a thread. In addition, mothers and fathers can make similar toys themselves and introduce their children to wild and domestic animals in a playful way. Also, older children, following step by step and relying on photographic material, can make a bear cub with their own hands and give it to their younger friends.

For manufacturing you will need the following material:

– sheets of colored paper in blue, red and orange; – white cardboard (1 sheet); – PVA glue or pencil; – scissors; – a coil of wire with a diameter of 0.45 mm; – a simple pencil; – an awl; – a stand for making holes with an awl in the places where the parts of the teddy bear are attached; – a spool of thread; – a black thin marker for drawing the eyes and nose of the teddy bear (can be replaced with black paper); – a toy template – a teddy bear: the base of the toy, the back and front legs (elements of movement), 12 washers PC.

Description of work

Step No. 1. Using a pre-prepared teddy bear template, you need to cut out “clothes” from colored paper to make the toy bright. To do this, mark out the decoration elements for the teddy bear on colored paper. From orange paper - a teddy bear's nose, a blouse (upper body), from blue paper - a tie and panties (lower body).

Step No. 2. Now we cut out all the parts with scissors.

Step No. 3. Using a glue stick, glue the orange parts onto the teddy bear (nose, blouse).

Step No. 4. Then glue the blue parts in the same way: pants, tie, draw the eyes with a black marker and outline the outline of the nose.

Step No. 5. Take an awl and a stand to make holes in the parts - the legs of the toy and on the main part of the teddy bear.

Step No. 6. Take a spool of thread and cut 4 parts from it, each up to 20 cm, then fold it in half (for strength). We pass it through the upper holes into the bear's paws and tie it with a knot.

Amazing Barrel - From a log on a lathe!

Step No. 7. To fasten the parts we will need wire, scissors and an awl.

Step No. 8. You need to cut a piece of wire about 10 cm. Then thread it like this: washer, main part (body), washer, foot, washer. We twist the ends of the wire with a spring using an awl.

Step No. 9. We managed to attach the upper and lower legs to the body in this way.

Step No. 10. On the back side of the toy we tie together the threads of the upper and lower legs. We cut off the excess threads.

Step No. 11. Now you need to connect with a thread the upper fastening of the thread, which connects the front paws, with the lower fastening of the thread, which connects the hind legs of the bear cub, in order to make movements using it, pulling it down.

Step No. 12. The toy - the teddy bear is ready to start playing!

An accordion paper bear is an excellent and easy craft for children. The technique is popular, using it as a basis you can make many funny animals and birds.

The following materials are used in the work:

• Brown cardboard;
• Orange cardboard;
• A simple pencil, a compass, scissors, a glue stick;
• Markers.

How to make a barrel out of clothespins

To make such a barrel you will need a little time and the most ordinary items

Author: Irina Lysenko. For the portal Masters of Handicrafts

Blog: Grunkin's autumn

Materials:

Cut a piece of fabric measuring approximately 13 by 10.5 cm

Make 0.5 cm cuts on one edge (which will go down the can)

Lubricate the inside of the jar with PVA glue

We also coat the fabric with glue.

Glue the fabric inside the jar, straighten it so that the edges are glued end to end. If the fabric is long, it’s better to pull it out and cut off the excess

Cut the edges of the fabric at the top

Bend it outwards and glue it

Cut out a cardboard circle slightly smaller than the diameter of the jar and a piece of fabric for the bottom

Glue the cardboard to the wrong side of the fabric, make cutouts on the fabric around the perimeter

Fold and glue the edges of the fabric

Glue the bottom into the jar

We disassemble the prepared clothespins into two parts. It took me 12 pieces

Glue the clothespins with a hot gun.

It already looks very much like a barrel.

All that remains is to decorate. Wrap the bottom part with hemp rope

Now we wrap the upper part.

It is better to secure the rope between clothespins with glue

We also wrap the edge of the jar with hemp

Making a lid. Cut out several circles from cardboard. They should fit inside the Pringles lid. We cut out thick felt or padding polyester of the same diameter. And a piece of fabric with a diameter larger than the lid - taking into account the bend of the fabric

We assemble a kind of sandwich: first we put cardboard in the lid, then felt on top. It is better to lightly lubricate each layer with Moment-Crystal type glue. Cover the top with fabric

We trim the edges, coat them with glue, fold them over and glue the fabric onto the lid.

We poke a hole in the center,

We screw in the self-tapping screw from the inside of the lid.

On the front side, screw a wooden bead onto the end of the self-tapping screw.

Now we’ll make a protrusion on our lid that will go inside the jar and prevent the lid from moving off. Cut out several circles from cardboard with a diameter slightly smaller than the diameter of the jar from the inside

Glue the circles together. If you have thick cardboard, you can cut out one circle. I have a thin one - I glued 4 mugs.

And glue it to the bottom of the lid

Glue jute rope to the edge of the lid

You can stick a couple of ladybugs from a florist store

How to make a wooden barrel with your own hands

Cooperation is one of the most difficult crafts, so the answer to the question of how to make a barrel with your own hands will also not be easy. This is a very labor-intensive process that requires the performer to have a decent professional level and a large number of tools for wood processing.

Before you are interested in how to make a barrel, you should decide what you need it for. The choice of material and manufacturing method depend on this. This type of container is manufactured for the following purposes:

1. ​for fermentation, aging and storage of spirits, wine and beer;
2. ​ for preparing and storing pickles;
3. ​for storing dry products;
4. ​for storing honey, etc.

Beverage barrels have two bottoms and a hole for inserting taps. The same type of container, but without holes, was previously used for long-term storage of certain products (for example, corned beef).

Wooden oak barrel

For other purposes, barrels with one bottom are sufficient - they are also called tubs. They are covered with a lid or a circle on top for oppression. These parts are much easier to make than the bottom. You can make a wooden barrel from such types of wood as:

1. ​oak;
2. ​ash;
3. ​cherry;
4. Linden;
5. alder and others.

The wood of the first three types is the most versatile. It is equally suitable for containers for any purpose. However, the “champion” should be recognized as the oak barrel, which, being strong, reliable and durable, provides ideal conditions for storing food.

Oak products have antiseptic properties, release tannins into alcoholic drinks, improving their taste, and also easily withstand the effects of brines when preparing pickles.

Ash and cherry are the first “substitutes” of oak wood. They have similar, but weaker properties. Therefore, we will look at how to make an oak barrel with your own hands.

The production of containers from other types of wood, such as linden, has no fundamental differences except for the nuances of finishing.

Oak barrel for honey

Rules for procuring material for barrels

Before you start making a wooden barrel with your own hands, you should prepare and prepare high-quality material. The wood must be mature, healthy, and free from defects (knots, cross-layers)

Wooden barrel base

The best time for harvesting material is late autumn or winter, when the natural moisture content of the wood is at a minimum level.

It is unlikely that you will be able to meet all the requirements. For example, to make staves for wine and cognac barrels of the highest quality category, the process of drying and aging wood takes 6–8 years, but if you are only concerned about how to make a barrel for yourself, adhere to the following rules:

1. Before drying, the logs are split into pieces of the required thickness;
2. ​ drying is carried out in a place protected from direct sunlight - under a canopy, in a barn, etc.;
3. ​ The duration of drying depends on many factors and can take 1–3 months;
4. The residual moisture content of the wood before treatment should be about 25%.

Accelerating the drying process using hot air and other methods usually leads to a deterioration in the quality of the wood and its properties in the finished product. Tips on how to make a wooden barrel with your own hands also take into account the need to condition the processed rivets before assembling the product. As a result, the residual moisture content of the wood should be 17–20%.

Making rivets and tools for this

For those who want to make an oak barrel themselves, the most difficult thing will be making the staves. The process of marking and chopping logs is clearly presented in the following figure

Preparing materials for a wooden barrel

As a result, you will receive blanks of conical cross-section, from which, after drying, they are made into rivets. This part has a complex shape, so its production places high demands on the skill of the performer. The main dimensions of the barrel and its elements, depending on the volume, are as follows:

This table will help you figure out how to make a barrel, and the drawing will help you understand how to give the rivets the desired shape

Tool

and what tools you will need for this. The curvature of the sides should provide the barrel with a taper of about 8°, due to which the product becomes resistant to loads from the outside and inside.

To process the surfaces of rivets, a plane, jointer, sherhebel, plow and other tools of this group are used.

In this case, the outer surface of the part should have a slightly convex shape, and the inner surface should have a concave shape.

Linden honey barrel - DIY Community on DRIVE2

...well, a barrel sounds loud, so - a barrel). Let me make a reservation right away - while working as a radio engineer, I am not a professional in carpentry (I just love tinkering with pieces of wood since childhood). I don’t have any cleverly crafted special tools, and I think anyone who wants to, whose hands don’t interfere with sitting, can do no worse. From the age of 15 I had the idea of ​​trying to make a barrel - but only 20 years later I tried it. From about that time on, there was a log of linden that had been felled when I was at school. I sawed 12 slats about 10 mm thick. I think it would be even better if they were prepared with an ax along the growth rings - but the log was small and, as usual, good thoughts come late.

I cut out a support part from oak for bending the workpieces.

Before bending, the slats were first boiled, but then, being too lazy to run to the kitchen, I pumped out the air from a liter jar with a compressor lying around idle from the central lock - this way the workpieces got soaked much faster.

But in general - the wood is very soft and gets wet well - you can just soak it. Using clamps, I pressed the soaked workpieces against a supporting piece of wood.

I waited for it to dry, but then I got tired of it and sped up the process by fixing the strip with nylon thread and drying it in the microwave at low power

I gave a slope of 15 degrees to the side ends of all slats.

I did this with a belt sander, but it was not possible to maintain the angle; the assembled workpieces formed cracks on the outer surface - I had to finish it manually on a plane with sandpaper

I laid the slats on the adhesive side of the paper tape.

In this form, it is extremely easy to assemble everything into a cylinder.

Having missed the seams, the carpenter pressed the glued cylinder together.

I glued the end to a pine board and screwed it with screws to a sleeve of a suitable size (pre-prepared for the existing electric motor).

I think it was possible to attach it to a drill. Sanded the outer and inner surfaces.

And he made a recess under the bottom.

I cut the blank, turned it over and glued it to the board again to cut the same groove for the lid. From thin (5 mm) slats I glued a plate for the bottom and lid.

And he cut out round pieces with a reserve diameter using a hand jigsaw.

Having processed the surfaces manually, I glued the bottom.

From an apricot strip on the same electric motor, I used a knife and sandpaper to grind out a lid handle.

Glued it to the already processed lid.

From stainless steel from an old gas stove, I cut out two strips 10 mm wide for hoops (what would a barrel be without them).

I riveted one of the edges of the strips to give the shape of an arc and subsequent tight fit of the hoops.

I secured the ends with stainless steel rivets (annealed pins from stainless steel hollow rivets).

I smoothed it out a little with scissors, polished it and placed it on a barrel. For decorative purposes, I decided to glue the drawing to the side wall.

This familiar bear is what we will do)

I redrawn the picture by eye onto a half-millimeter end cut of an apricot board (it didn’t turn out quite like it - I had to try it as a carbon copy).

cut out fragments with nail scissors after soaking the wood

I glued the cut out pieces to the side of the barrel.

I covered the inside with wax, spreading it with a brush onto a surface heated with a hairdryer. The outer surfaces were coated with oil for products in contact with food. I think it was necessary to treat the entire surface with wax.

What is the best way to ensure safety?

Honey should be stored in any container at a temperature from +5 to +10°C. It is believed that the ideal place for this is the refrigerator. However, you can’t fit a lot of cans there.

If you have stocked up on the product in large containers, then you need to place them somewhere in the underground or the coolest corners of the house, protected from light. Honey in barrels and aluminum flasks can stand without additional shading, but transparent plastic needs to be covered with something dark. The same should be done with glass jars.

Products sent for long-term storage must be checked periodically. This should be done even if storage conditions are ideal.

The fact is that honey can separate, crystallize and ferment. Crystallization is a natural process, but separation and fermentation can occur due to poor quality production. Usually such incidents happen with a product that contains a lot of water. As a result, the bactericidal properties of honey are weakened, which leads to increased activity of fungi and bacteria.

Such honey can increase in size, which leads to leakage from the vessel, tearing off the lid and other troubles. As a result, not only are the medicinal and taste properties lost, but in the absence of a sealed lid, the foaming liquid may leak out of the vessel. For this reason, you should never fill the vessel right up to the lid; you should leave some free space in case the fermented mead climbs like dough, tearing off all the lids.

Bees take a long time to prepare their product. They pass the collected nectar through their crops, enriching it with enzymes, and then dry it for a long time. And only after a sufficient amount of water has evaporated from the sweet preparation, it becomes honey and is sealed with special wax caps.

In an effort to start selling their goods earlier, beekeepers can remove early, not yet dried honey. It cannot be stored. You just need to eat it soon. It is advisable to purchase autumn products for storage, preferably in September.

For long-term storage of honey at home, it is best to use wooden barrels, glass jars and aluminum flasks. Plastic, despite the fact that it is considered food grade, still has its own smell, incompatible with the aroma of the bee product.

Thus, storing honey is a complex and delicate process. The more sweet amber you stock up on, the more care is required to ensure its safety.

How is honey stored in a tub?

A barrel or tub of honey should be kept in a clean, dry (humidity up to 60%) and cool room. The barrel should be well treated with beeswax and covered with a tight, airtight lid. The container should not be exposed to sunlight, the room should not be hot, dark, with a stable temperature without changes. Optimal temperature: from −6 to +20°C and it is better to stick to the golden mean.

Important! Strongly odorous foods or substances are not allowed nearby: fish, pickled vegetables, pickling, building materials, varnishes and paints, flammable or toxic substances. Honey very quickly absorbs any foreign odors.

Under the right conditions in a linden tub, honey can retain its characteristics indefinitely. It will not change in composition, taste, or appearance.

Honey pots: what are they, what kind of wood are they made from

A wooden linden barrel of honey is a harmonious union of two related natural materials. The shelf life of honey in contact with linden wood that is tolerant to it is unlimited! A tub is a container similar to a barrel, only a slightly different shape. It can be made from the same material, the pros and cons are almost the same. The only caveat is that the tub cannot be kept on its side, while the barrels fit perfectly in a horizontal position.

I made a “barrel” bottle decor from jute and cardboard. DIY gifts

Wood for making barrels and tubs: oak, spruce and pine, cedar, linden, aspen, larch, sedge, beech, birch. The best options for storing honey are linden, aspen and chin. Deciduous trees are also suitable: poplar, alder, willow. Although some experts criticize them, giving preference exclusively to linden wood. But an oak barrel, so valuable for storing drinks and pickling, is absolutely not suitable: the honey in it will darken. It is also better to exclude tubs made from coniferous wood: the honey in them will acquire a resinous smell.

Pros and cons of tubs

To store honey, in addition to barrels and tubs made of natural wood, the following can be used:

• glass containers,
• glazed ceramic,
• aluminum, tin coated inside with food grade varnish,
• stainless steel flasks.

Important! Copper, lead, and galvanized utensils are prohibited - honey reacts in them, forming oxides dangerous to human health. Of the permitted types of containers, the palm belongs to linden tubs and barrels.

Advantages of a tub made of linden wood:

Linden lends itself well to processing

• Gives products unobtrusive, very pleasant flavor shades that harmoniously combine with the taste of honey.
• Ease of manufacture. Linden lends itself well to processing. This is a juicy, light and pleasant material.
• Beautiful wood. Of course, this is a matter of taste, and one can argue which is more beautiful: oak, cherry or walnut. But linden, even not being among the top five most beautiful types of wood, has a pleasant appearance. The color of the wood is fresh, white with pinkish tints and a harmonious fiber structure. Products made from linden are bright, cheerful, and light.
• High density of wood, which protects honey well from external influences.
• A linden honey barrel can be kept empty for a long time, the wood has a low percentage of shrinkage, and the product does not lose its insulating properties. They do not need to provide special conditions for storage.
• Linden barrels do not need to be soaked before use, like oak barrels.
• And finally, the elongated and slightly truncated shape at the top allows the honey to maintain its natural structure.

Note! In winter, natural honey acquires a thick consistency. This is a natural and obligatory process: the honey pumped out of the honeycomb begins to crystallize. When stored in a barrel, a dense core is formed, which floats to the top, forming a natural plug. This honey will last for decades.

Crafts from newspapers “Barrel of Honey” ❀

The disadvantages of wooden utensils for honey are due to purely economic issues:

How to make wax candles. Nuances./ The Fetistov family

• such containers are more expensive than glass or plastic,
• when choosing them, you need to “be in the know” so as not to purchase a poorly made barrel,
• Usually they are convenient for storing fairly large volumes of honey, which not everyone can afford.

However, the traditions of cooper craftsmanship have recently experienced a rebirth. Environmentally friendly natural materials and products are highly valued, which is why wooden tubs and barrels for honey are increasingly being bought and sold. And if this valuable household item is made with your own hands, it will bring even more pleasure.

Barrels for honey

• discount Barrel 0.3 l. (linden), waxed, hoop (rope)
• discount Barrel 0.5 l. (linden), waxed, hoop rope
• discount Barrel 0.75 l. (linden), waxed, hoop (rope)

• 
  discount Barrel 1 l. (linden), waxed, hoop: (gold)

• 
  discount Barrel 1.5 l. (linden), waxed, hoop: (gold)

• discount Barrel 1.5 l. (linden), waxed, hoop: (pigtail)
• discount Barrel 3 l. (linden), waxed, hoop: (pigtail)
• discount Barrel 3 l. (linden), waxed, hoop: (gold)
• discount Barrel 1 l. (linden), waxed, hoop: (pigtail)
• discount Barrel 0.75 l. (linden), waxed, hoop (braid)
• discount Barrel 0.3 l. (linden), waxed, hoop (gold)
• discount Barrel 0.3 l. (linden), waxed
• discount Barrel 0.5 l. (linden), waxed
• discount Barrel 0.5 l. (linden), waxed, gold hoop
• Barrel 15l (linden) waxed, lid with rope handles
• discount Barrel 0.75 l. (linden), waxed
• discount Barrel 0.75 l. (linden), waxed, hoop (gold)
• discount Barrel 1 l. (linden), waxed
• discount Barrel 1 l. (linden), waxed, hoop: (rope)
• discount Barrel 1.5 l. (linden), waxed
• discount Barrel 1.5 l. (linden), waxed, hoop: (rope)

Popular containers of our time

For the mass consumer, wooden barrels and ceramic dishes are expensive delights. The most popular and affordable utensils are containers made of glass, plastic and metal:

Honey barrels are usually made from oak, linden, acacia, maple, mulberry and other aromatic, but not resinous, types of trees. The ideal option is linden. However, linden is also an excellent honey plant, so every felled tree is a loss for bees and beekeepers.

A barrel produced specifically for storing a sweet product can be manufactured in the following options with:

In other words, this is not only packaging for a sweet product. This is a work of art that will decorate any cellar. Moreover, it is a wonderful gift that can please any person who is not alien to the joys of life and the desire for beauty.

Bee protection

The leadership of the US, EU and other countries are trying to take concrete measures to prevent or slow down the development of events regarding the extinction of bee colonies in some areas. Issues of protecting beekeeping and the bees themselves are discussed not only at scientific and beekeeping forums, but also at meetings of governments and parliaments.

Various public campaigns are constantly being conducted that are aimed at protecting bees. Various environmental organizations, individual food industry and agricultural companies are constantly joining these campaigns. Numerous monographs are published, documentaries are made, and materials from various journalistic investigations are published.

Beekeeping is constantly analyzed by scientists. Over the past 3 years, approximately 200 different reasons have been reviewed that can cause mass deaths of bees throughout the planet or in certain regions. Half of the scientists place the main blame for all the modern ills of beekeeping on the use in agriculture of pesticides that are deadly to bees.

This point of view is supported by the majority of members of the International Association of Beekeeping Associations, in particular their president, Gilles Ratia. Other reasons include varroa mite, beekeeper mistakes, depleted diet of honey bees, bee diseases, bee parasites and viruses, climate change, environmental pollution, as well as constant interaction between all factors and a certain “still unknown” factor. .

Since 2008, two UN agencies have been involved in the protection of bees and other pollinating animals: the Food and Agriculture Organization (FAO) and the Environment Program (UNEP), which have been allocated approximately $25 million for these purposes. Pollinator protection ( bees in particular) is included in the development strategy of the World Organization for Animal Health (OIE). So, beekeeping is under reliable supervision.

DIY decorative barrel of honey

DIY decorative barrel of honey

To make a barrel of honey you need:

— pine block 48x48 mm; - wood cutter; - corner chisel; - cautery on wood.

Making a barrel of honey:

On a block we measure a piece 7 cm long. Cut it off. This is our preparation.

To further process the workpiece we will need a wood cutter. Using a pencil, mark a circle on the top of the bar with a diameter of 4 cm. It is very important to hold it so that the fibers run vertically.

Only after following this rule do we begin to remove excess material along the intended radius. As a result, you need to get a cylinder. With a pencil we mark the border of the upper hoop and begin to round off the upper part with a cutter.

To give the hoop volume, you need to make a cut along its upper border and slowly remove the material from the top of the barrel to the cut line.

There should be a “threshold”. We do the same procedure with the lower part of our barrel. We also make cuts on the raw edges of the hoops and remove excess material. We do this in such a way that we get two voluminous hoops. Now we will work with a corner chisel. It is needed to show each stave (plank) on the barrel. We outline the lines along which we will make the indentations and begin to remove excess material. Now we have shallow grooves and our workpiece has become like a barrel. Become the author of the site, publish your own articles, descriptions of homemade products with payment for the text. Read more here.

Accordion paper bear step by step

Making the torso

The bear's body consists of long strips of cardboard folded into an accordion.

Cut 2 strips across the entire long side of the A4 paper. If you need a big bear, you need to cut two more strips and glue them to the ends of the first ones. Or initially use larger paper so that you can immediately cut out the strips. The width of the stripes is selected based on the size of the bear. In this master class – 2 cm.

Apply glue to the tip of one strip and glue another strip to it to form a right angle.

Start making an accordion, moving the strips one after another one at a time. For example, first point the bottom one up and press it, then the strip on the right, etc. There is no need to use glue at this stage.

But when both strips form an accordion, the tip needs to be glued.

Draw and cut out the double legs. The top should be slightly wider than an accordion so that the bear looks stocky and club-footed.

Crafts from newspapers “Barrel of Honey” ❀

Glue both parts in front and behind the accordion and the body will take a stable position.

Making a head

The easiest way to create a bear's head is to use ordinary circles. After all, even kids draw a completely realistic bear using small and large circles.

Using a compass or stencil, draw and cut out:

• A large circle made of brown cardboard that will be the bear's head;
• Two small brown cardboard circles for the ears;
• Orange circle - for the muzzle;
• If desired, make a small accordion neck using the same technique as the torso. That is, use thin and small strips.

Glue the ears, muzzle onto the large circle-head, draw semicircles in the ears, nose, smile and eyes. The latter can be made from paper, using purchased moving eyes.

Final stage

Glue the neck to the body with paws. You can do without a neck, but with it the craft looks funnier and more beautiful.

Attach the head to the neck and the accordion paper bear is ready.

The same technique is used to make an accordion dog, and by changing the head and shape of the paws, you can make many different animals.

All kids like bear-shaped toys, and polar bears are one of the most beautiful New Year's souvenirs. These animals can be made with your own hands from paper, cardboard, natural materials and other available materials.

Let's look at the main, most popular options for creating crafts in the form of bears.