Do-it-yourself cardboard twitchers: templates for how to make toys, master classes, photos

DIY mobile frog

The jumping frog is very common in origami. It is best to make such a craft from dense material. The ideal option is thin cardboard. If folded from thin colored paper, the frog will not jump, since the material is not springy.

The classic color is green, but it is acceptable to make a more cheerful or even exotic pink (or any other) frog.

The process of making a moving frog consists of the following steps.

1. You need to take a rectangular-shaped cardboard and place one of the short sides towards you. Next, on the top you need to fold the classic model of a water bomb.
2. Both sharp corners need to be bent outward and upward. In this case, there should not be even a minimal gap between the “spouts”.
3. Bend the outer vertical edges to a line in the same direction so that they meet at the point where the front legs of the future frog begin.
4. Then you need to bend the bottom edge of the structure. And the top edge must be bent down and back. At this stage, that very important spring element should be formed, which will replace the frog’s hind legs.
5. The final version of the animal should be the same as shown in the figure.

In order to set the structure in motion, you need to place your finger on the back, press it to the surface and slide back. From such actions the frog will jump up and forward.

Mobile toy “Squirrels with nuts”

“Squirrels” are performed according to the same principle as “Chickens”. All main parts are cut out of cardboard of the appropriate color using templates, and finishing parts are cut out of colored paper. Assembly is carried out according to the diagram. This toy has one complicating element - the moving legs of the squirrels, attached to the silhouette using movable joints.

When the toys are set in motion, the squirrel figures not only move themselves, but also swing their paws into which the nuts are glued. When playing, it seems that the squirrels are stacking the collected nuts in a heap.

Making a Jumping Bunny

In the same way, you can easily and simply make another moving toy using the origami technique - a jumping hare. Before you start creating a composition, you need to prepare all the necessary materials. There are few of them:

• a square sheet of double-sided colored cardboard (you can choose the color yellow, grey, orange or any color you like);
• black marker or felt-tip pen.

The manufacturing process consists of several stages.

1. First you need to put a sheet of cardboard on the table. It is better if its size is 12 by 12 cm. A center line should be marked on it. Next, you need to direct the two sides of the square towards it so that you get a rectangle. And then the same rectangle must be bent to make a square shutter. This is clearly shown.
2. The previous fold can now be unfolded, and on this surface, by raising the corners, you need to select isosceles triangles.
3. Next you need to create two isosceles triangles. The corners must be lowered down and the resulting workpiece smoothed out.
4. At this stage, the corner should be returned to the opposite direction again.
5. The upper corner of this corner needs to be lifted and bent back, and only then unfolded the entire structure.
6. To highlight the ears of the future bunny, you need to bend the paper.
7. At the final stage, you need to lift the structure and unfold the side bends. Make another bend and lift the ears up.
8. Lower the tips of your ears back.

Now you can move on to the decorative part of the work. So, you will need to use a prepared marker or felt-tip pen. Using it you need to draw the animal’s face. The structure is ready.

Where craft weapons come in handy

A paper gun can be either a simple toy for home entertainment or an accessory that complements a stage or carnival costume. At New Year's parties, many boys dress up as cowboys, pirates and super heroes. Therefore, homemade weapons will come in handy more than ever.

At the same time, modeling weapons out of paper can be a serious hobby for adults. Professionals of this art can create things from paper that are no different in appearance from their combat prototypes.

Homemade models can serve as interior decoration or, for example, a decorative element of a congratulatory panel made for a man on a special occasion.

Of course, children will be inspired by the idea of ​​creating a weapon with their own hands, especially if it is a gun made of cardboard that shoots. A craft can be very realistic if you pay special attention to its design.

Paper mock-ups of finished weapons

To make homemade weapons, you can use ready-made models for assembly. This could be a Makarov pistol, Revolver and other types of firearms.

These mock-ups contain drawings and assembly instructions. They can be complex or simple.

To make it, you will need to transfer the drawing onto cardboard or thick paper and assemble the elements following the numbering.

Assembling weapons using ready-made patterns is accessible and educational for both children and adults. Having mastered modeling skills, you can learn to create drawings yourself.

Download a free layout (template) of a Stechkin pistol in PDO or PDF format.

Download a free layout (template) of a Glock pistol in PDO or PDF format.

How to make a twitch toy from cardboard: master class

It’s quite easy to make a twitch doll with your own hands if you use the technology suggested below. When making moving toys, it is important to take the advice of professionals who recommend:

• Perform piercing of parts with an awl.
• Use brads as fasteners.
• During the manufacturing process, use only PVA construction adhesive, which is characterized by increased thickness and quick drying.
• Cover the cardboard with a layer of colored paper and press down the parts to be glued while they dry, which will make it possible to avoid deformation of the product.

Below you can find a step-by-step master class on how to make a twitch using the example of constructing a cardboard Puss in Boots. To work you will need:

• sheets of white paper;
• packaging micro-corrugated cardboard or ordinary cardboard;
• stationery knife;
• scissors;
• fastening material;
• awl;
• double sided tape;
• nylon thread;
• glue stick;
• glue "Moment".

Stage 1

The first step is to start preparing the cardboard parts. To do this, templates are cut out and printed on white paper. Double-sided tape is glued to the back of the parts, and the templates are then glued to the cardboard from its reverse side.

Sketch details must be cut with an allowance

Stage 2

Carefully cut out the details of the craft using a stationery knife. Holes for fasteners are made in them with an awl. Depending on which fastener will be used, you can calculate the required hole diameter.

The animal's paws overlap. Using an awl, you will need to poke holes in the upper edges. They will be used to control the limbs. A lightweight polymer cord is threaded into the area of ​​the openings of the torso and limbs. The ends of the cord are melted with a lighter.

To create a movable mount you can use:

• buttons;
• wire;
• threads;
• brads, etc.

Stage 3

To create a mechanism for controlling the limbs, it is important to tie the cat’s paws in pairs with nylon threads, which will need to be threaded through small holes. By pulling the threads, the paws can be moved to the lower position. A long thread is tied to the horizontal, upper and lower ones. On the reverse side of the puller, knots are tied on a light polymer cord. Now you need to test the product for free rotation of the limbs. If everything is in order, the ends of the paracord (cord) melt.

Stage 4

A pair of circles are cut out of cardboard, the diameter of which does not exceed 25 mm. The circles are glued together with “Moment”. This part is glued to the animal’s head from the wrong side (on a loop of narrow tape). The cardboard craft is ready. Primary school students can make it themselves. DIY dynamic toys will delight any child.

To create a movable mount, it is best to use brads

What materials and tools will we need?

To create toys you will need cardboard and colored paper. In some cases, you can also use thick paper (whatman paper) followed by coloring and velvet paper.

To glue the parts of toys and their elements, it is better to use PVA glue, and movable connections are made using wire loops (spirals) threaded through through holes.

In some toys, the parts are set in motion using strong threads stretched between the moving parts on the back of the toy.

Tools required for work: scissors, awl, needle.

Making loops for fastening parts: cut a piece of thin wire 5-6 cm long, make several turns of wire around the rod of a ballpoint pen or a thin long nail, thread the straight end of the wire through the connecting holes of the toy, repeat the operation with turns of wire, thereby connecting the parts between yourself. It is important not to squeeze the parts together too much, as they will become inactive.

Bear

A simple bear can be made using the origami technique using the same principle as a cat.

All you need for this is a square piece of paper. For this craft, it is better to use single-sided paper. But double-sided is also suitable.

Bend the sheet diagonally.

Fold the resulting figure in half.

Now, along the marked lines (see photo), bend the two corners towards each other.

Bend two corners slightly to the sides.

Bend the two edges of the corners inward.

Turn the workpiece over.

Fold the top layer of paper up.

Fold the top and bottom corners inward.

It turns out this is the face of a bear. All that remains is to paint it with a black marker. Add eyes, nose and mouth. Ready!

Twitch bear toy

To create a moving three-dimensional bear, just follow the step-by-step guide, which will help you avoid making mistakes during the work. The created mechanism will allow you to raise all the paws every time you pull the string.

Before the master starts creating a simple toy, he will need to take care of purchasing:

• cardboard in the desired shades;
• colored paper;
• scissors;
• adhesive base;
• a small amount of soft wire, which will help fix the paws movably.

Step by step process

1. The bear template can be printed for convenience. According to this sketch, you will need to outline the torso along with the upper and lower limbs on cardboard.
2. The eyes, nose and ears of the animal are cut out and drawn on with a felt-tip pen. The apron area is glued to the central part of the bear's belly.
3. The animal's limbs are fixed to the body with wire.
4. The paws are tied with threads on the reverse side.
5. Now you should test how well the toy moves after the child pulls the string. In a similar way, you can create an owl-shaped twitch.

A moving bear will give kids a lot of pleasant emotions.
Making moving toys is a great way to spend time with your child. The product manufacturing schemes presented above will help both adults and children cope with this task.

Dog

Another figure, similar to a cat and a bear, is made from a square sheet of paper. It is very simple and uncomplicated, but at the same time even preschoolers can learn the origami technique.

Take a square piece of paper.

Fold a square piece of paper diagonally.

Bend the upper corners down along the pre-drawn lines.

Fold the two bottom corners up.

Draw eyes and nose on the figure with a black marker. It turns out to be a dog's head!

Simple crafts machines

When doing joint creativity with your child, it is important that the technological process does not last very long. Otherwise, the child will simply get tired and lose interest. Therefore, a little time should pass from the start of work to the appearance of a new machine.

Read also: Is it possible to wash your hair after henna?

In this case, a toilet paper roll can help out. A racing car model can be made from it in a few steps.

1. You need to cut an oval-shaped hole in the cardboard sleeve. This is the driver's cabin.
2. The sleeve must be painted, covered with colored paper and stickers. A racing car must be bright!
3. The wheels must be attached to the hub. They can be made from cardboard or plastic bottle caps. You can take an axle with wheels from a toy car.
4. Place a pilot in a racing car. This can be any small figurine.

Another version of the simplest truck model is also simple and can be made from scrap materials in a few minutes.

Racing car

In just an hour, you can easily fill the entire toy car park by making cars from paper of different shapes and brands.

In order to make a model of a paper racing car with your own hands, you need to take a standard A4 sheet.

1. Fold the sheet in half lengthwise. Fold the corners inward on both sides, forming arrows.
2. Fold the longitudinal sides towards the middle under the arrows.
3. On one side, fold the arrow towards the middle, making it even sharper.
4. Lift the other side and place it on top of the folded arrow, tucking it in between the layers of paper.
5. Bend the tail of the car. You can draw headlights on it.
6. To make it clearer how to make a paper machine, you can give another drawing diagram.