DIY headphone bracelet: how to make a headphone bracelet

Devices began to age faster

If you add up the forecasts for smartphones, headphones, fitness trackers and game consoles, then this year more than 2 billion devices will be released.
Each of them has its own life cycle, at the end of which it becomes obsolete. On average, Russians change smartphones every two years, and Americans every three. The shorter the lifespan of a device, the more often you will have to buy new ones and the more devices will become obsolete every year. The term end of life is used for products - this is the date after which the manufacturer will no longer repair devices or release updates for them. After this, the care of technology finally passes into our hands. It seems that something needs to be done with outdated and broken devices, but so far there are few options.

— Send them to recycling, where people risk their lives to tear the batteries from the case.

— Send them to the compactor, where they might accidentally explode.

- Throw them away, knowing that the plastic case will take another 400 years to decompose.

It would be great if we had one beautiful answer to the question “What to do with old devices?”, but until we have that answer, we should pay attention to how we treat technology right now

Slipknot

In the last few years, rope bracelets have become especially popular among young people. If the base is most often made of nylon cords or specially woven chains, then the decor can be very diverse. Some needlewomen even weave a bracelet with different ropes. However, not every clasp is suitable for such decoration. The sliding knot looks best in this case. There is nothing easier than making a clasp on a cord bracelet in this style.

The convenience of this fastening lies in the ease of putting it on. In addition, it allows you to easily adjust the size with just a pull of the thread.

This is done in the following way:

The ends of the bracelet are placed on top of each other crosswise.
One of them is wrapped around the main strand (on which the decor is strung), a loop is made on the right, and then exactly the same on the left.
The end of the cord is threaded through both holes and pulled into a tight knot.
Then they retreat a little and repeat the manipulation, forming a similar knot. It is important to note that when performing the second element, you must not confuse the threads, otherwise the bracelet will not be adjustable.
The final stage is trimming the excess length and burning the ends, which will prevent blossoming.

How to make sound on headphones?

Let's return to the question of how to make headphones. First, let's determine what kind of headphones they are, wired or wireless, as well as the degree of their damage, are they connected correctly? So, how to make sound on headphones? Everything is simple here. Click on the volume control, which is located at the bottom near the clock. Move the volume control up. If that doesn't help, then look at your headphones and find the volume control on them. It is usually shaped like a small wheel between the plug and the headphones, try turning it. Make sure the headphones are inserted into the correct green jack. You have turned on the sound and the next question is how to make the headphones louder? Let's discuss a few options. One of them is to adjust the sound in the system through the maximizer program. Another way is to use a special audio player, for example, VLC, in which you can set the volume to 200%. You can also look for new drivers for your sound card. Or you can buy an inexpensive headphone amplifier, it fits almost all models. In general, we will advise you to use headphones from the manufacturer monsterbeats, and you will no longer have to think about how to make the headphones work. And the very last thing we can tell you is how to make headphones with your own hands.

This key also brings the face shield closer to your face and gives you a better view of the action, or can be replaced after a break. It also features a headphone jack to accommodate regular stereo headphones or the headphones that came with the device. The remote control has been designed to be easy to use even while wearing a headset.

The result will be similar to the image presented on the social screen. The resulting video stream will be similar to what users see on the social screen. The stream will be identical to the presentation of the social screen mentioned above. If small glossy surfaces are not usually a problem, make sure they do not cause detection problems.

How to make headphones with your own hands?

The most common and frequent failure of headphones is when only one earphone works. You can try to open the one that is not working and see if one of the wires has come loose, which is what happens most often. If you have a soldering iron, a sharp knife and scissors, then you can solve this problem yourself. The problem may also be in the plug; carefully remove the insulation from it and resolder the broken contact. But all the problems that happen with headphones will disappear!

Virtual reality: which headphones to choose?

Thus, there are no problems with the trip. If you have technical difficulties with your helmet, you can also contact the section directly for help. We explain everything you need to know before buying them. The concept is finally quite simple: it should immerse the user in an alternative world that only exists before his eyes in relation to his movements. Finally, for the illusion to be complete, other senses must also be deceived: hearing through headphones, but also touch and why not smell.

Progress

Necessary materials:

Old headphones
Clamp
Hardcover book
Accessories

To make it easier for you to understand the weaving process, we took cords in two colors.

You need to use a clip to attach the headphones to the book.

Take the pink wire and place it under the white one.

Let's pass the end of the pink wire under it in the same way as shown in the photo.

Sale is good, give it even better

A few years ago, we mainly saw websites specializing in buying phones and tablets flourishing on the Internet, so much so that they now have a special comparator. Some associations may also have access to collection points at waste disposal centers or large distribution companies. If this is not the case, they are redirected to a recycling scheme. Eco-organisms are the official channel for our used products when they cannot be reused.

Electronically controlled electronic waste

Responsibility of waste producers

Of the remaining 20%, 8% is recovered through energy production and 12% is ultimately incinerated or disposed of in landfills as non-recoverable waste. E-waste left on sidewalks is dismantled and looted by metal scavengers, making disposal and recycling difficult. Let's tighten the knot. Adjust the tightness of the knot yourself, depending on how openwork and airy you want the choker to be.

Now we do the same actions with the white wire. Let's carry it out first under the pink one, and then under its own base.

Renewal Commitment: 1 for 1 is not always well respected?

However, we guarantee that pure online players are no more or less virtuous than physical stores. It's hard to test without doing a great comparative study. However, the law stipulates that it must be presented: “systematically, visible and easily accessible.” In addition to 1 to 1 there is also 1 to 0 in the case of small appliances. They are required to collect your small used equipment even if you don't buy anything. Specifically, this is materialized in the form of a collection and sorting of furniture created by eco-organisms.

And tighten the second knot.

We weave the tattoo choker in this way to the length we need. We tie a knot as shown in the diagram above and fasten the fittings.

As it turns out, making a tattoo choker with your own hands is very simple.

The length of the headphones is enough for a bracelet, and the charging wires are enough for a necklace.

You can also weave beads and pendants into the choker, this will give the jewelry a more finished look.

If you like original jewelry, you can spray paint your choker with any bright or metallic paint. Such decoration will not go unnoticed.

Magnetic rectangle locks

Most women have seen this type of lock, as it is often used to secure bracelets, wallets, clutches and other haberdashery items. You can purchase such a retainer at any store of the relevant goods.

Let's look at how to make a clasp on a bracelet from magnets:

Classic bracelet regaliz. Beads, rings, charms and other decorations are strung on a leather strap. Then a very thin layer of glue is coated on the inside of the lock and glued to the cord. It is important to maintain a balance here, because if there is too much glue, it will squeeze out and the product will look untidy.
Bracelet with braided cords. Regaliz fittings can be combined not only with cords, so you can safely choose other, most suitable materials. The lock is coated with a thin layer of glue and one or more braided cords are inserted into it, depending on their thickness or diameter. Then, if desired, decorative parts are threaded through or dispensed with and the lock is glued in a similar way on the opposite side.

To decorate such a clasp in an unusual way, you can insert a decoration on a chain with an original keychain into it along with the end of the bracelet.

Weaving options

There are several possible options for making jewelry from broken headphones: weaving from stripped wires, weaving with knots and weaving in the macrame style.

Making bracelets from wires without braiding requires additional tools: for example, a soldering iron. Knotted headphone bracelets are the simplest jewelry. This technique is accessible even to primary school students. But the appearance of such decoration is far from neat.

We should also highlight the bracelet around the neck - a choker, which is very popular among girls. If the purchased decoration is made only in black, then using cords you can create a variety of color combinations.

Macrame

A great way to make a beautiful earphone bracelet is to use a flat macramé knot on a pencil.

Bracelet making technique:

Two loops (two sets are required) from the headphones are attached to the pencil so that 4 cords of the same length are formed. It’s easier to call them numbers from 1 to 4 from left to right, so as not to get confused.
Take the far right wire of number 4 and throw it over numbers 2 and 3, the far left goes over the fourth, goes under the second and third and goes into the loop of the fourth. Now the first number becomes the fourth and the same manipulations are performed with it. The resulting knot is tightened.
Now the process is repeated on the other side in a mirror image. This way the entire bracelet is made to the desired length.

You can see how to make a bracelet from headphones using the macrame technique in the following video:

Knots

This bracelet requires two headphones with a round cord or one pair with a flat double cord that can be broken by pulling the ends. Initially, you need to cut the headphones themselves and attach the two ends with tape to the edge of the table, fixing them securely. If the cord is double, then simply do not cut off the plug, but attach it to the table, this will make it easier to work.

Weaving begins by tying the first knot, which is pulled to the end of the secured edges. Then a second knot is tied and pulled to the first. You need to pull the knots one to another tightly and evenly to make the bracelet neat.

You can see how a knot bracelet is made from headphones in the following video:

A variation is the knotted weave, in which the earpieces serve as a clasp. To do this, a knot is tied on the wires a couple of centimeters from the headphones. Next, the nodes are adjusted to one another, forming a rigid bracelet. Once the bracelet of the required length is ready, a loop is formed at its end into which the clasp earphones are pulled.

Made of copper wires without braid

You need to remove the braid from the wire without cutting the plug. This will prevent the wires from falling apart.

We braid four wires along the entire length of the cord. We divide the resulting braid into segments that correspond to the size of the wrist circumference. We use a soldering iron to solder these segments into one at both ends to get many braids in the bracelet. Metal tubes from lock fittings, sold in any handicraft store, are put on the ends.

The disadvantage of such jewelry is not only the need for soldering skills, but also the fact that the bracelet can stain the skin.

Choker

The choker has a peculiar weave that allows the bracelet to stretch to fit the head and shrink to fit the neck, without squeezing it. Decoration woven in this style looks impressive and is very easy to make.

Making a choker bracelet - in the following video:

The prepared wires are fastened with a paper clip. The right wire goes around the left one in front and is pulled back over the formed loop. The same is done with the left wire - it is passed in front around the right one and pulled out over the girth. In this way, both wires are alternately woven to a chain of the required length.

In the first case, securely tie the cords in knots and cut them as close to the knot as possible. In the second case, you will have to remove the braid from the cord and twist the wires together. It is ideal if you fill them with hot glue so as not to prick the skin of the neck. For the third option, you will need to open the microphone box, remove the wires from there and insert the ends of the choker in their place. Then snap the box shut.

With wire

If you want something completely original, then an option is possible when a strong wire of the required length is inserted into the headphone cord. Then the wire is formed into a spring of several curls. A bracelet painted with gold or silver acrylic looks impressive. To prevent the headphones themselves from dangling on your wrist, they can be fixed in the desired position with hot glue.

Copper wire bracelet

Hello! Today I will tell you how to make a bracelet from simple materials at hand: copper wire and beads (they can be anything: ceramic, glass, stone, wood, acrylic... - whatever! :)) It seems to me that making such bracelets is very simple. The main thing is to get used to it and you can make a lot of them, and then wear them all together - it looks very nice

Let's move from words to action!

For work we will need:

copper wire of different diameters (0.2 mm - 2.4 m; 0.4 mm - 3 m; 0.8 mm - 1 m; 1.3 mm - 25 cm)
pliers
round pliers
side cutters
needle file
hammer and anvil
needle or thin knitting needle (about 1 mm in diameter)
beads (glass, stone, ceramic) - 3 pcs. Desirable:
ammonia
paste GOI
boron machine
caliper (to determine the wire diameter)

Progress

Step 1. Cut 25 cm of the thickest wire (1.3 mm). This will be the base of our bracelet. We need to make a loop on it. But first, let’s sand the end of the wire so that while wearing the bracelet it does not scratch or catch. To do this, we will use a needle file (instead of a needle file, you can use sandpaper or even a nail file). Check the surface with your finger to make sure it is smooth and not scratched. Now we grab the tip of the wire with the very tip of the pliers and gently bend it.

Then you can bend the resulting loop back a little. We get a loop that resembles the eye of a pin. If there are traces of tools left on it, they can also be removed with a needle file.

Step 2. Cut 1.35 m of wire with a diameter of 0.4 mm and wind it on a thin knitting needle or needle (I use a needle with a diameter of 1.2 mm). We try to make the turns even and tight, but if somewhere there is a small distance between the turns, that’s okay.

We've got a spring. We string this spring onto a piece of 0.4 mm wire and begin to wind it onto the base of the future bracelet. Be sure to leave the “tails” (which stick out from the spring).

When you have wound the entire spring, you need to secure it. To do this, we make a few more turns around the thick wire and cut off the excess. We press the tip tightly to the base of the bracelet using pliers - on one side and on the other.

Step 3. Cut 20 cm of wire with a diameter of 0.8 mm, leave a “tail” and also wind it around the base wire (place it between the coils of the spring). We attach the “tails” to a thick wire (make a couple of turns).

Step 4. We need to hide the base of the spring: the places where we secured the ends of the wires look completely unattractive. Usually end caps are used for this, but it very often happens that there are no suitable ones on sale (the required shape, diameter). But we will get out of this situation easily and gracefully! We take the thinnest wire (0.2 mm) - a piece of about 40 cm and wind it directly onto the ugly place. We make a kind of “ball”. When the segment ends, we hide the tip inside the “ball”. Nothing should cling while wearing! At the other end of the spring we make the same “ball”.

Step 5. Now we move on to the most interesting part - decorating the bracelet with beads. Here you can give free rein to your imagination: you can use a variety of beads: made of stone, glass, clay, wood, metal, homemade ones from polymer clay. You can use dividers and caps, whatever you like in the hardware store. If you want, instead of separators between the beads, you can make the same “balls” of thin wire.

Step 6. Next, repeat steps 2-4: make another spring, put it on a thin wire and wind it on a thick one. We wind a wire with a diameter of 0.8 mm between the turns. Don’t forget to secure the ends and press them tightly to the base wire. Again we use “balls” to hide the unsightly ends of the spiral.

Step 7. Now we cut off the end of the thick wire, leaving a tail of 1.5 cm. We need to make another loop from it, as we did at the other end of the bracelet. Don’t forget to sand the tip, then use round pliers to tighten the loop.

Step 8. Clasp. You can buy a ready-made clasp, but we will try to make it ourselves. We take a 0.8 mm wire and twist a figure eight: to do this, you need to twist it around a thick knitting needle (or a pen, a pencil - in a word, something round).

We twist the ends of the figure eight with round pliers into the smallest loop.

We have an S-shaped clasp. All that remains is to push it away from the folds, then it will become stiffer and will not straighten out if the bracelet is pulled strongly (you don’t need to do this on purpose anyway). We beat it with a hammer on an anvil (if you don’t have an anvil, you can replace it with a second hammer or just a flat steel platform). You need to hit very carefully, with several weak blows, and not one strong one.

The second part of the clasp is the ring. We make half a figure eight, bending the tip into a small ring.

And on the other side we make a smaller loop using pliers. We also bend the tip into a loop. We beat off a larger ring on the anvil.

To attach the bracelet clasp, carefully bend the bracelet ring up...

...insert the clasp and close the ring back. We do the same on the other side. Give the bracelet a rounded shape (you can do this on a small jar, or you can just do it with your hands).

Step 9. The bracelet is ready. But we can improve it even further: apply a patina to create a noble antique effect. Patination can be done with different compositions: sulfur liver, sulfur ointment, but we will use the most accessible method - patination with ammonia vapor. To do this, we need regular ammonia (10% ammonia solution), which is sold in pharmacies. First, degrease the product (you can wash it with a regular sponge and dishwashing liquid) and dry it well. Then, in any container, for example a jar, pour ammonia solution to the bottom and hang the bracelet at the top (make sure that it does not come into direct contact with the liquid) (Fig. 17). Close and wait until the color of the product changes (usually 2-3 hours).

Step 10. Now all that remains is to polish our bracelet to emphasize the volume and depth. The most convenient way to do this is with a bur machine using GOI paste. You can polish it manually using felt, a piece of jeans or just a soft cloth. Drop a little machine oil onto a cloth, rub it into the paste and begin rubbing the bracelet in the protruding places. Polish until a beautiful bright shine appears. Now the product needs to be washed thoroughly; for this it is convenient to use an old toothbrush and dishwashing detergent.

That's it, you can wear it!

Thank you for your interest! If you have any questions, be sure to ask

UPD: I'm adding photos of other bracelets made using the same technique. And there's more here

How to make a choker from headphones: instructions and diagram

There is a standard choker weaving pattern, which is the most common. This is exactly what the most popular “collar” looks like. Before weaving a choker from headphones, read the step-by-step instructions. The execution scheme is similar.

To find out more, go here. But copies will be available at participating dealers on launch day, October 13th. Click here for more information. They also bring an incredible sense of immersion into the virtual world. This method takes the last image displayed at 60 Hz and creates a new image at 120 Hz based on the last head movements performed by the user.

This list will be updated regularly. It will be updated regularly. Its range of games spans a wide range of genres, including shooting, puzzle, racing, horror and more. The players enter a salon where several characters are drinking. . We hope, however, that publishers will offer a wide range of prizes and experiences.

To make the diagram clearer, the cords on it are highlighted in different colors.

Here's a short step-by-step instruction. If you have any questions, please come back.

We cut off all unnecessary parts from the headphones.
2. Carefully, so as not to cut the cords, remove the latch at the point of their connection. We separate the cords along the entire length.

3. Use a stationery clip to secure two cords side by side. Wrap the right cord around the left loop.

The true resolution of a cinematic screen depends on the screen size and the resolution of the content being displayed. The current cinematic mode is a virtual screen floating in a black space, such as when you are in a movie theater that is pitched in darkness. It can be worn for a long time.

However, as with any display device, we recommend taking a 15-minute break every hour. Is there a risk of myopia with long-term use? These are the optimal viewing conditions required to watch a 60-inch TV. You can bring lenses closer and further away from your face for maximum comfort.

Nikolai

Now we will talk about how to make headphones and what to make from old headphones, as well as much more. Has your Favorite device, which has accompanied you everywhere for many years, finally broken down? Do you somehow not want to throw away your old headphones or do you just feel sorry? Take your time, there are several ideas that will extend the life of your headphones. The most common of them is to weave a bracelet from your headphones, the use of which you can come up with yourself. Also, some craftsmen make small speakers from old headphones by making holes the size of the speakers in the bottom of a plastic cup. Using the Internet, you will find many other options.

However, particularly large or unusual glasses may not be suitable. Q: My head is larger than average. However, if you have any doubts, the best thing to do is go and try it for yourself! It is recommended to turn off surround mode or use standard stereo headphones with a cable that does not support surround sound.

A button located on the back of the helmet allows you to unlock the arch mechanism to open the helmet above your head. Once placed on your head, two knobs located above and below this button allow you to adjust and stretch the headband to ensure the helmet stays in place and securely in place. The most important element of the helmet is the visor. There's a key on the bottom right edge of the screen that, when pressed, allows the visor to move forward or backward to adjust the vision. Press this button to extend the visor screen and leave room for glasses or pause to see your surroundings.

Bracelet "Macrame"

For this you will need:

Faulty headphones (one or more colors).
Pen or pencil.
Patterns for weaving macrame.

So, we are making a bracelet from old headphones.

We divide everything into separate wires.
We attach them to a pen or pencil.
We intertwine the wires according to the instructions for weaving macrame. Due to the fact that there are many types of macrame weaving, you can create your own unique and original accessory.

How to make a bracelet from headphones in the form of a spring

To do this, you will need wiring from one of the headphones and a piece of flexible thin wire. Calculate approximately how long you want to make a bracelet from non-working headphones.

Now cut the required length of wire and separate the connected double headphone wires to make one wire. You don't have to remove the earphone; it will serve as an additional decoration.

Carefully push the separated wire from the earphone into the middle of the wire cavity, after which you wrap the bracelet around your hand, but not tightly, so that there is no swelling. Ready! Now you can show off the new decoration you made with your own hands!

Ready! Now you can show off the new decoration you made with your own hands!

LiveInternetLiveInternet

Let's move from words to action!

For work we will need:

copper wire of different diameters (0.2 mm - 2.4 m; 0.4 mm - 3 m; 0.8 mm - 1 m; 1.3 mm - 25 cm)
pliers
round pliers
side cutters
needle file
hammer and anvil
needle or thin knitting needle (about 1 mm in diameter)
beads (glass, stone, ceramic) - 3 pcs. Desirable:
ammonia
paste GOI
boron machine
caliper (to determine the wire diameter)

Step 1. Cut 25 cm of the thickest wire (1.3 mm).
This will be the base of our bracelet. We need to make a loop on it. But first, let’s sand the end of the wire so that while wearing the bracelet it does not scratch or catch. To do this, we will use a needle file (instead of a needle file, you can use sandpaper or even a nail file). Check the surface with your finger to make sure it is smooth and not scratched. Now we grab the tip of the wire with the very tip of the pliers and gently bend it. Then you can bend the resulting loop back a little. We get a loop that resembles the eye of a pin. If there are traces of tools left on it, they can also be removed with a needle file.

We've got a spring. We string this spring onto a piece of 0.4 mm wire and begin to wind it onto the base of the future bracelet. Be sure to leave the “tails” (which stick out from the spring).

We twist the ends of the figure eight with round pliers into the smallest loop.

The second part of the clasp is the ring. We make half a figure eight, bending the tip into a small ring.

And on the other side we make a smaller loop using pliers. We also bend the tip into a loop. We beat off a larger ring on the anvil.

To attach the bracelet clasp, carefully bend the bracelet ring up...

...insert the clasp and close the ring back. We do the same on the other side. Give the bracelet a rounded shape (you can do this on a small jar, or you can just do it with your hands).

That's it, you can wear it!

Glass bead pendant

Using glass balls, you can create simple but original jewelry, including pendants in the form of a bracelet for your hand. To do this, first place the balls in an oven preheated to 260 degrees for 20 minutes, and then immediately place them in water with ice. The result will be workpieces with internal cracks, but a smooth surface.

To make a fastening for such a bead, you will need a cap and a pin, the hook of which is inserted with the loop up, and another loop is formed from the remaining end for the chain.

All that remains is to smear the inside of the cap with a sufficient amount of glue and fix the bead. Based on the length of the chain or cord, you can turn the product into a pendant or bracelet.

Magnetic buckle lock

This type of clasp for a bracelet does not require additional decorative elements, since the buckle itself, as a rule, is decorated with beautiful carvings, intricate patterns or inlaid with stones. It's a great idea to use a lock like this on a thick product. Depending on the diameter of the recess, a thick cord or many thread-like ropes made of beads, felt, or leather can be used.

This idea is especially suitable for those who are interested in the question of how to make a clasp on a bead bracelet. Both parts of the lock have a small recess, which is lubricated with glue and placed on the ends of the product.

How to make a choker from headphones: instructions and diagram

To make the diagram clearer, the cords on it are highlighted in different colors.

Here's a short step-by-step instruction. If you have any questions, please refer back to the previous post.

We cut off all unnecessary parts from the headphones.
2. Carefully, so as not to cut the cords, remove the latch at the point of their connection. We separate the cords along the entire length.

3. Use a stationery clip to secure two cords side by side. Wrap the right cord around the left loop.

4. We carry out the same action with the left cord.

5. Next we make similar loops, alternating the cords.

6. Continue weaving according to the pattern.

The headphone choker is ready! It turned out pretty cute! The loops of the decoration stretch, making it easy to put on over your head. At the neck they take a regular shape, easily adapting to any size.

Of course, on this basis you can come up with your own model, which may be even more original.

Do you want to know what to wear with a choker? Check out our tips - original sets in tumblr style!

How to weave bracelets from laces

Laces are an excellent material for weaving bracelets. These can be thick or thin laces, fabric and leather, laces of a wide variety of colors and textures. You can use as many laces as you like in one bracelet. A little tip: don't forget about the right color combinations and try not to overload the composition with ten different laces. Below in the photo you can see techniques that are perfect for beginners: Sometimes bracelets made of laces alone look rough, then they should be diluted with delicate and romantic beads: A bracelet made of leather will look stylish and fashionable. Just take some leather laces or ropes and make a simple but elegant braid:

Video

Making wireless headphones from wired ones! (13 photos + 1 video)

To begin with, I bought these same wired headphones - not the original ones, of course, but just well-made Chinese ones (folding, durable)

and the cheapest Bluetooth speaker-keychain for 130 rubles

Naturally, the column cannot be built in entirely; it was immediately disassembled. The Chinese speaker is easy to disassemble - it fell apart on its own. All that is needed from it is the internals and then only the control board and the battery.

The speaker has one speaker, but we don’t really need it, we cut it off too. Having disassembled the headphones (only one ear needs to be disassembled, since in the other there is just a speaker and a wire to the second ear we need, where the control board will be attached), I soldered the headphone speakers to the board and checked the entire structure for robotic functionality

Then I tried on how the board would fit in the new case

Marked and made holes for turning on and charging in the headphone case

I wanted to use the button from the column as a power button, but it was already lost during the hectic activity and I just put a bolt, making it a power button. First I hooked the board up to the power cable - this way it would be better to center it along the holes in the case (you won’t miss it) and glued everything with hot glue.

Then all that remains is to put everything back together and test it!

The headphones turned out very well. If I hadn't lost the button, it would have been fire! Charges for about 2 hours and plays for about 3 hours. I recommend this device! And yes, my case was chosen to be very flat, so the battery did not fit in and I secured it inside the darling. If you like the idea, you can watch the creation video here.

Cord Knots

Today there is a wide variety of bracelet weaving techniques. Craftswomen use different types of knots to create original and spectacular products.

Classic types of braiding include: four-cord braid, single and double puzzle, maiden braid and circular braid.

Even new weaving techniques are based on classic knots. Each needlewoman chooses a type of weaving that is convenient for her.

The bracelet made using the Turkish head knot looks impressive. It is woven around a cylinder that must fit the size of your wrist.

To complete the bracelet, you need to make a strong knot.

There are several types:

Surgical - first you need to make one so-called “half-knot”. To create it, you should hold one end of the cord with one hand, and draw the other end around the first. Then create another half-knot. To secure, the lace is wrapped twice in the first half-knot, and once in the second. After this, the ends of the cord should be cut, leaving no more than one and a half centimeters.
The usual way is to insert one end of the lace into the loop on the other side, then move the knot away from the loop and tie the ends together. But this option is impractical.
Sliding is one of the most difficult options because it requires time and patience. It can be used to secure cotton cord.

To tie a lace, you need to leave a margin of 14 cm on each side. You need to create a loop from the right lace, and the tip should be on the outside edge. Take the left lace and circle the loop with it several times, then you need to create three more turns. After this, the two ends need to be pulled into a loop and tightened.

Next, we perform the procedure again to form another node, which will be passive. Then you need to make a loop at the second end of the lace - circle the free end five times and tighten it into a knot. You need to insert the remaining end into the resulting loop. The node is ready.

Spring bracelet

First, let's create a bracelet from headphones in the shape of a snake. What you will need: elastic narrow wire and one of the wires. Estimate the approximate length of the future item. Cut a suitable piece of wire. You can throw one of the speakers for decoration. Now carefully push the wire into the braid of the former earphone. Try to implant it so that it gets between the wires inside - then it will be easier for you to push through, and the braid will not get holes and deteriorate. When everything is ready, wrap the headphone bracelet around your wrist in the form of a spiral snake. Secure the free end to the “button” of the speaker. And flaunt an elegant piece! A similar product will not look very simple if the braid is not standard black, but gold or silver. Naturally, such a design will be more exciting. Although the idea of making a bracelet out of headphones is already extraordinary!

Pigtail bracelet

The following example of unique jewelry you are invited to make in the style of braiding. Here you can already fantasize to your heart's content. For example, use not single, but double and even triple weaving. And combine the wires with multi-colored braiding to make the headphone bracelet look more elegant. Take three wires of approximately the same length. Fix one of their ends with something so that they hang freely along the entire length. At least stick it to the edge of the table with tape. Now we explain how to make a bracelet from headphones. First, fold all three braids and make a common knot. And then weave a regular “braid”, but it’s better not tight, but looser. Try it on your wrist so that the product does not end up being too wide and slipping off your wrist. Ready? Make another one, maybe in the same color scheme or another one - to your taste. Tie knots so that the “braids” do not come apart. Finish making a bracelet out of headphones with your own hands like this: using a thread or another wire, connect both “braids” so that the jewelry comes out wider. Secure with speaker clasps or alligator clips. Looks interesting, right?

Bloody necklace is a Halloween trend

Every year at the end of October the Day of the Dead is celebrated. “Nothing American is alien to us,” our compatriots paraphrased the classic and began to prepare appropriate outfits, apply frightening makeup to their faces, and paint their nails black. Jewelry on this day takes on an ominous hue: rings with skulls, earrings with devils and bats, a necklace in the form of a web with a spider. It will take very little time to make a bloody tattoo choker.

The patience spent will be rewarded with a peculiar neck decoration, which from a distance resembles streaks of blood.

This is a silicone choker, but you can make a beaded jewelry similar to it

In the arsenal of means for producing the bloody “strangler”, the main materials are:

fishing line;
red beads;
15 beads to match the beads.

We cut the fishing line as follows: 8 pieces of 2 cm each, 7 pieces of 3.5 cm each and 1 more - according to the volume of the neck (taking into account the ties). Make a knot at the end of each of the 15 short pieces. First we thread one bead at a time, and fill the rest of the segment with beads. We tie the free ends to the long part of the fishing line. We alternate the resulting “pendants”, starting with a short segment. The approximate gap between the hanging threads is 1.5 cm.

Don’t forget to string the beads onto a long fishing line, the ends of which are tied in knots when finished. The finished tattoo choker can be completed with a clasp or simply tied the ends together.

How to make a clasp on a beaded bracelet on a machine

For a beadwork woven using a special device, a ribbon clip can serve as a lock. Before attaching it, both edges of the bracelet are secured with threads or thin fishing line. Then each is inserted into clamps, which are squeezed with pliers until they hold tightly.

The loops on the lock can be connected with a lock, ribbon, carabiners or a pair of pins. Clamps can be purchased ready-made or made on a machine yourself.

Making your own bracelet guarantees its uniqueness. In the process of work, you can show your imagination, creativity and creativity, use any materials you like, and choose a design taking into account your personal style. And the original clasp, corresponding to the style of the product, will add originality to it.

Unique DIY silver bracelet

Greetings, Samodelkins!

In this article, the author of the YouTube channel “Bonn Factory” will show the detailed process of making a silver bracelet with your own hands. By following the instructions below, you can repeat this project if you wish.

It was decided to print the links of the bracelet on a 3D printer, since the author does not yet have rollers or other hand-held jewelry tools.

Next, according to the logical parts we have learned, we will get 3 silicone molds. All this is necessary so that we can more conveniently and quickly copy the necessary elements in the quantity we need.

In the near future, the author plans to switch to a vulcanizer, as this is a more modern and professional method of creating forms, but for now we will use plastic formwork, a glue gun and two-component liquid silicone the old fashioned way.

Our Christmas tree is completely assembled, of course it’s not the smoothest yet, but still already like a real one.

Also, the master is not used to making parts with a reserve because he still strives for qualitative indicators, and not for quantitative ones. Well, except that one additional link was made from the calculated value, since it is difficult to estimate the required length of the bracelet, because he had never had to deal with them before. Next comes the process of forming and calcination. Here everything goes according to the standard technical process for this operation. First you need to dilute the mixture in the following proportion: per 100 grams of gypsum 38 ml of pure distilled water. And in order not to miss the moment of setting of the gypsum, it is necessary to do all this with the stopwatch on and perform the molding within seven minutes from the moment water enters the dry mixture.

Next is the assembly. The author began to assemble the product without thinking about the direction of the asymmetrical links with faces, and naturally made a mistake, but noticed it in a timely manner and successfully corrected it all.

Author's video:

Source

Become the author of the site, publish your own articles, descriptions of homemade products and pay for the text. Read more here.

Rules for choosing a clasp for a bracelet, types of locks

When choosing this element for your product, you need to take into account some nuances and follow a number of rules. The most important of them is ease of use and the ability to put on or remove the bracelet yourself. In addition, the lock must be securely and firmly fixed so that the decoration does not have to be lost.

Another important point is the overall combination with the product and attractive appearance. We’ll look at how to make a clasp for a bracelet with your own hands so that it meets all the requirements later in the article.

The following types of locks are most often used for hand bracelets:

magnetic;
carbines;
clamps;
hooks;
latches;
toggles;
chains;
screw;
ties.

Headphones - a “second” life

Every music lover who listens to music through headphones has repeatedly encountered the problem of their sudden breakdown. And every such amateur will confirm that most breakdowns occur as a result of the headphone wire breaking near the plug. How to solve this problem? Throw away your headphones and buy new ones? Don’t rush to throw away your headphones, because in just half an hour you can breathe a “second” life into them. And now we will discuss how to do this.

Tattoo choker: its features and varieties

The similarity in the name of such jewelry and tattoos was due to their visual identity. The neckpiece is so thin and elegant, it fits so intimately to the body that at first glance it will seem like a drawing by a skilled craftsman. Only upon closer inspection can you discover that a well-executed accessory has been mistaken for body art.

Tattoo Choker features a variety of weaving materials. In art and hardware stores you can buy colored fishing line, craft wire or knitting threads. All this will serve as an excellent material for weaving openwork “collars”.

Today, in addition to styling their necks, young divas decorate their wrists, ankles and even fingers in the form of rings with choker bracelets. This design is minimalistic and not pretentious, it is not bulky or protruding, and, therefore, is suitable for those girls who like discreet accessories.

A tattoo choker is suitable for everyday style and will also complement other jewelry.

In addition to ordinary, single-layer tattoo chokers, there are also double ones, but they, probably due to the inconvenience of wearing, are not particularly popular. Tattoo bracelets and tattoo “collars” made of beads are a special chic for teenagers.

Tips for work

Looking at the photos of wire crafts, you may notice that there are one or two techniques per job. This decision is made by the masters for a reason and allows them not to overload the final result.

Do not combine chenille and copper wires in your crafts, as almost always the result will not be what you expect. If you have such a desire, or have unused material left, resort to the help of works presented on the Internet.

Use a soldering iron only when it is rational to use it, for example, it can be used to divide a thick wire into two parts or connect a piece of metal thread if it is impossible to attach it to a craft in any other way.

Leather bracelet

To make this popular, stylish bracelet at home, you don't need any special sewing or leather working skills. Decorating here is also not difficult, so even a child or a beginner can master making a leather bracelet!

Prepare a piece of leather measuring 25x5cm. The length may be different: measure your wrist and add another 2-3 cm for the rivet. Round off the cut at the edges, giving the desired shape with scissors, as in our template.

The main highlight of this decoration is the bow. This is what we need to form now. Carefully fold the piece of leather so that neat folds form in the center.

Now you need to secure the folds: to do this, wrap the middle with strong threads in several turns (it is better to use a polyester spool).

Cut a piece of leather measuring 4x1 cm.

Wrap it around the center, masking the thread ring, and sew it on the back side into a ring.

The final touch is to attach a snap to both edges of the bow to turn it into a full leather bracelet.

Thanks to the variety of shades of the material, such a decoration will be appropriate both in a classic toilet and in a trendy look for a friend.

Features of weaving cord bracelets for beginners

Baubles from this material are made in plain and colored ones. Materials can be purchased at stores selling haberdashery, accessories and fabrics. There are leather, velvet, satin, nylon and twisted waxed threads. The founder of this type of needlework is the macrame weaving technique.

For those who have never created such bracelets, we advise you to start with the simplest models. They are no less attractive than complex weaving. Even a child can cope with them. Simple nodes are used in the work. Such as flat square or “Turkish head”. The work will take a minimum of time when using the most ordinary base, but the result will exceed expectations.

You can start learning from hand-twisted floss threads, and then purchase more practical materials.

The history of the decoration

The history of this decoration goes back to the distant past, when ancient Indian tribes wore wicker collars, either to protect a vulnerable part of the body during battles, or as a talisman against evil spirits. Only that neck “armor” was made from natural materials - bones and teeth of killed prey.

In medieval Europe, wearing chokers made of silver and with pointed spikes served as a way to protect oneself from “dark” forces and from criminals.

In medieval Europe, wearing chokers made of silver and with pointed spikes served as a way to protect oneself from “dark” forces and from criminals

The Renaissance and Classicism made the choker a real work of art

The Renaissance and Classicism made the choker a real work of art. Necklaces that fitted the neck were made of precious stones, the basis of which was gold and silver threads.

Modern subcultures, wanting to shock the public, have introduced leather chokers, inlaid with metal rivets, spikes and elements of dark symbolism, as part of their image. In the 90s of the last century, buying this accessory was not difficult. The era of today allows you to make a choker with your own hands.

Modern subcultures, wanting to shock the public, have added leather chokers inlaid with metal studs, spikes and elements of dark symbolism as part of their image.

https://youtube.com/watch?v=ukxt6NbHbZE

Wire pendant with stone

This DIY pendant is made from gold, copper wire and stone. It is better to take the last element with a hole to make it easier to attach it to the decoration.

For the braid, 2 equal pieces of copper wire, one millimeter thick, are taken as the base. It will have to be wrapped with gold wire, which is twice as thin as the base.

The copper pieces are folded parallel to each other. After this, they begin to connect them with gold wire in a spiral according to the principle: 4 turns around one base, 2 turns around both bases.

Having made the decorative braid of the required length, you need to thread one of the free ends into the hole in the stone. After this, place the wire around the perimeter of the center of the decoration. After this, the remaining ends of the copper wire are masked under a decorative curl at the top of the pendant.

A loop is formed from the other end through which the chain will pass, and after making a spiral, the ends are fixed in the center on the inside of the product. In a similar way, you can make other models of stone pendants with your own hands.

How to make a bracelet. A selection of master classes

There are many ways and technologies to make beautiful and bright bracelets with your own hands. This collection is about simple techniques using scrap materials, sometimes even recycling recycled materials) For each type, I will offer a short description of the process, clarifying points that are not visible from the photo. The simplest bracelets, of course, are assembled with silicone thread. You can complement such bracelets with metal beads and pendants (To attach the pendant, use a connecting ring or bail)

Fabric bracelet. We sew a ribbon from thick fabric, a thick trouser type ribbon is sewn inside for greater density, fasten the fastener, sew on various beads, pendants, and connectors. For the intermediate connection, half rings made of dense wire were used, similar to those that are sewn onto the belt of a bag. It seems to me that this part could be replaced with some kind of bronze-colored connector or a wide end for ribbons. To prevent threads from being visible when embroidering, I recommend using thin transparent fishing line.

Here is a fastener option with . I like it even better this way. And it’s not at all difficult to do.

Another option to make a bracelet with your own hands is to crochet it from a thick synthetic cord-yarn. For additional decoration, a thin chain is threaded between the layers of thread.

If you don’t know how to knit, you can use a piece of ready-made knitted fabric. It is glued onto a thick base and the edges are hemmed. And this is the beauty in the end