Interesting crafts from disposable plastic containers

Bags made from plastic containers

You will need a transparent plastic container (the lid can be colored), a thick cord, rope or ribbon, a hole punch, glue and various shells, as well as glitter or bunches of imitation flowers. Make two holes on opposite sides. To decorate the lid of a plastic container, you need to use glue on the lid and arrange shells and glitter or a bouquet of flowers. Punch two holes in the container opposite each other, 1/2 cm below the rim. Pass the cord or ribbon through the holes in the lid and then through the holes in the container so that the ends are on the outside. Tie a large ornament at each end of the cord to prevent it from slipping through the hole.

Advantages and disadvantages

Before making and installing sprinklers, you need to consider all the pros and cons of a homemade drip irrigation system from bottles. The main advantages of such devices include the following factors:

significant water savings; when using a watering can or hose, a much larger volume is consumed;

In addition, it is worth noting that homemade watering structures facilitate human labor. This is due to the fact that such watering makes the soil softer, weeds begin to grow worse, so it becomes much easier to care for vegetables.

Important! As for the disadvantages, unfortunately, they also exist. Such irrigation systems often become clogged, so they will have to be cleaned regularly. Although experienced gardeners have found a way to eliminate such problems. You can simply equip a plastic container with a special drainage; for this you will need ordinary nylon tights. This material does not rot at all and allows liquid to pass through perfectly.

• There are other significant disadvantages of do-it-yourself drip structures, these include:
• the system cannot be applied over a large area, since this will require a lot of bottles, and in this case the dacha will not have an attractive appearance;
• plants receive a limited amount of water;
• difficult to use on heavy soil; due to poor soil, the eggplants become clogged and become unusable;
• In addition, some moisture-loving crops, such as cucumbers, will not have enough liquid provided by sprinklers if the weather is too hot. Therefore, in any case, they will have to be watered additionally.

Such homemade installations can be upgraded, making them more and more efficient. The manufacturing process itself does not take much time; it is enough to devote a couple of hours to the installation work. But the result, in the form of a rich harvest of healthy and tasty vegetables, will delight every gardener.

Making a banjo from a plastic container

To make a musical banjo, you will need a cottage cheese container or other plastic container of approximately the same size. Now cut 3/4cm long slits on opposite sides of the container. Cut a strip of thick cardboard 1/2 cm by 10 cm and then insert it into the slot in the container. Punch two small holes on both sides of the cardboard and then insert paper staples into both of these holes. Now take any elastic bands you already have and tighten them around the paper fasteners. Now pay attention to where the rubber bands cross the top of the container and make a 1/4cm cut in the rim of the container to hold the elastic in place.

Advantages

Before we begin to describe the technologies for making an irrigation system from plastic bottles, let's figure out why drip irrigation is considered the best. Compared to other irrigation methods, it has a number of advantages:

• Water is supplied directly to the root system. Thus, a “swamp” is not created around the plant, the constant presence of which is harmful to some crops;
• Water consumption during drip irrigation is minimal, since it is used exclusively “for its intended purpose”;
• The absence of excessive moisture in the area allows you to avoid the appearance of rot and the development of planting diseases;
• Drip irrigation is the only way to deliver water to plants in a timely manner when there is no one to look after them;
• And finally, you can make a drip irrigation system yourself, using only “available materials.” Thus, it will cost you practically free.

Well, now, having convinced ourselves of the undeniable advantages of drip irrigation, let’s proceed directly to the manufacture of an irrigation system.

New Year's flower pot

With tissue paper applique, you can turn an unwanted plastic container into a decorative item. Before decorating, wash the container with soap and hot water and remove all stickers, if any.

So, you will need:

• container;
• paper napkin;
• white acrylic paint;
• textured snow paint;
• glitter;
• glue for applique paper napkins or glue for decoupage.

You need to cover the container with white paint and let it dry completely. You may need to repeat the process if the paint does not cover the markings well. You need to remove the bottom 2 layers of paper towel and tear off the edges so that they become uneven. Follow the instructions below to glue the tissue paper to the container. While the glue is still wet, sprinkle glitter on the container if desired. Add textured snow paint to the top edge to give the container a winter look. Allow to dry completely.

How to make organizers from plastic bottles: master class

Plastic organizers like these can come in handy anywhere! In the bathroom you can put sponges or toothbrushes in them, in the kitchen - cutlery, cutlery or cooking utensils. In the nursery, several organizers can be placed on the wall and markers and pencils can be placed in them. And, of course, you can use them in your craft corner by placing the necessary little things there, from scissors and markers to threads or ribbons.

Organizers can be deep or low, large or small - it depends on what kind of plastic packaging you use for them. You can collect several bottles of the same shape and size and make a set in the same style.

In this master class we will show two similar options for making such organizers, from body lotion packaging and from tissue packaging for office equipment. But, guided by the same step-by-step descriptions, you can make organizers from different plastic packaging of a suitable shape and size.

To make handicrafts at home even more enjoyable, choose beautiful and comfortable home clothes. Pay attention to the patterns of home dresses, home trousers and home tops in our electronic catalog.

Idea: hanging organizer for handicrafts

How to make organizers from lotion bottles

You will need:

— plastic bottles of a sufficiently large size;

- paper, pencil, paper scissors for making a template;

- stationery knife-scalpel;

- scotch;

- permanent marker;

- cloth and alcohol;

- fine sandpaper.

You may also need a melamine sponge.

Step 1

Remove the covers. Wash the vials well and dry them.

Step 2

Carefully remove the stickers. If there is any glue left on the bottle, a melamine sponge will help to wash it off. You can also use vegetable oil applied to a cloth.

Get rid of any remaining glue, then wash the bottles again and wipe with rubbing alcohol - this will remove the last of the glue.

If your packaging does not have a removable label, but is printed directly on the bottle, you can try painting the bottle with universal acrylic paint. Do this after the stage of cutting out the organizer and sanding the edges and thoroughly degreasing the surface with alcohol. To make the paint stick better, you can use a primer before painting.

Step 3

Place a piece of paper on the bottle and mark how you will cut it. Remove the sheet and draw the template more evenly. Cut out the paper template. Glue it to the bottle with tape and use a marker to transfer the outlines onto the plastic. Remove the template.

Step 4

Use a knife to carefully cut out the organizer. Use a sawing motion and be especially slow when cutting curved edges.

Then sand the edges with sandpaper. Ready.

Perforated pegboard: 10 chic ideas for use

Organizers from tissue packaging

In exactly the same way, you can make organizers from packages of wet wipes for office equipment.

These bottles are larger and cylindrical in shape, so you can fit more items in each bottle.

Here is an example of how such organizers are placed on the wall in the area of ​​the working handicraft corner.

The convenience of organizers is that you can always easily remove the box with the necessary little things from the wall and take it with you, and then hang it back.

Photo and source: homeyohmy.com, makeit-loveit.com

Idea: DIY jewelry organizer

Make a wasp trap

Finding a wasp's nest in a garden or countryside can be difficult, and clouds of insects make it difficult to work and relax. Make traps out of unwanted bottles. Cut off the top of the bottle, place it neck down in the second part (without the cap). Pour some honey into the bottom. The wasps will be able to descend, but not get out.

apartmenttherapy.com

Root irrigation system

Root irrigation system

Making this drip irrigation system is very simple. The bottom of the bottle is cut off with a small piece of the wall, on which a vertical cut is made. As in the previous case, this part of the bottle will serve as a cap.

Near the neck, several holes are made with an awl through which liquid will flow.

The more clay soil you have on your site, the more holes you need for normal watering.

All that remains is to bury the bottle near the plant so that all the holes are underground. After filling the bottle with water, moisture seeping through the holes will provide the root system with a sufficient flow of water.

Holes can also be made at the base of the bottle, and water can be poured through the neck.

Ease of manufacture and the ability to irrigate several plants at the same time (in this case, the bottle is dug between them, and holes are made around the entire circumference) are the undoubted advantages of this system. The disadvantage is the fact that it is difficult to determine the intensity of watering, since the “working area” of the bottle is underground.

Pros and cons of plastic boxes

Advantages of plastic containers:

1. Durability . Plastic is not afraid of water, rust will appear on it, and pests or mold will not grow inside. The average service life of such a product is 100 years.
2. Tightness . The containers are seamless, with uniform wall thickness. If you choose a product with a tightly screwed lid, you don’t have to worry about the liquid poured inside ending up outside.
3. Light weight . Boxes can be placed on shelves without fear of them collapsing. In addition, the containers are convenient to take with you to work as lunch boxes.
4. Resistance to temperature changes . Plastic can be frozen and reheated in the microwave. However, the container must be marked in what temperature range it can be used.
5. No foreign odor . High-quality containers do not smell and do not spoil the taste of food.
6. A wide range of . There are products on sale in different colors and sizes, so you can choose containers that will decorate your room. For example, a real trend of the last year has been a design that imitates large knitting.
7. Affordable price . The products are inexpensive, but high-quality material cannot be completely cheap.
8. High strength . Plastic is second only to wood and metal in these properties.

Disadvantages of plastic boxes:

1. Susceptibility to deformation upon contact with hot surfaces and fire.
2. Fading or discoloration in direct sunlight.
3. Susceptibility to the influence of aggressive components . Acids, alkalis, gasoline and other liquids that can dissolve its walls should not be poured into plastic containers.

The main disadvantage of plastic is its harm to the environment. It pollutes the environment, enters the soil, seas and oceans, and fresh water bodies. In addition, people have been eating plastic for a long time. Scientists have calculated that every year each person unnoticed eats an amount of plastic equal to one tablet.

Device with valve

A washbasin made from a 5L bottle is easy to upgrade. I recommend purchasing a special spout for the traditional model at a hardware store. The price of the part is much cheaper than a ready-made hand washing design. I insert the pin into a hole in the cork, which I create in advance with a hot nail. If you touch the element with your fingers, water flows from under the part.

Instead of a plunger, I advise you to use a disposable 5 cc plastic syringe. I drill a hole in the bottle cap that matches the diameter of the medical instrument. The structure should fit easily into the hole without any liquid spilling out. At the device, I use a construction knife to cut off an area with a place for a needle. I carefully clean the edge from burrs and irregularities.

Source zen.yandex.com

I squeeze the syringe into the cork. The piston of the medical instrument should enter and leave the frame without effort. I make the washbasin body from a five-liter bottle. I remove the bottom of a plastic eggplant. I fix the device to a post or tree trunk using a self-tapping screw. To prevent the structure from moving, it is important to tighten the screw tightly.

I screw the stopper with the syringe in a spiral onto the neck of the container. If the entire piston is outside the bottle, then the water does not flow. All you have to do is lightly push the device inside the eggplant and the liquid will flow out. To completely block access to moisture, you need to pull the device all the way.

Source cozy-home-ideas.com

The role of the valve can be played by a nail or screw with a wide head. I insert the part into the hole of the cork, which I then screw onto the neck of the container. The disadvantage of the design is the lack of tightness, water drips or leaks. To seal the product, I string the steel element onto silicone. An elastic spacer will reduce the gap between the hole and the metal without affecting the mobility of the piston.

Instead of a valve, I recommend using a small rubber syringe. To increase weight, I additionally add fine river sand to the medical instrument. I insert the device into the eggplant through the cut bottom. I take my nose out through my throat, so I don’t need a lid.

Source sdelaysam-svoimirukami.ru

How to fold?

To ensure that bags take up minimal space, they must be folded correctly. Some of the most popular options are:

• Triangle – the bag must be placed on the table, all folds removed, and folded in half several times. Then a corner is folded in at the bottom and the polyethylene is folded up to the handles, which are then folded into the triangle itself. This option is most suitable for classic “T-shirts”.

• Tubes – in appearance, the folded bag will resemble the cake of the same name. This method should be used if you are going to store plastic products in a plastic bottle. Flatten the bag and roll it into a long, narrow strip. Then wrap it around your index and middle fingers, folded together, and tie the bag handles on top.

• Envelopes – this folding method will be useful if you have a lot of large packages. The product needs to be straightened, and then alternately folded in half, either horizontally or vertically. It is worth continuing the procedure until the specimen reaches the size you need.

Did you like the article? Then support us, click

:

A good idea on how to store bags in the kitchen may pop into your head unexpectedly. There is no point in shelving it. It will take a little time to make an organizer for products from PVC film.

It’s nice to have a few uniquely designed fixtures in your apartment. One for small food grade items, the other for bags with handles.

Washbasin with tap

The downside of all designs is that a person cannot control the direction of the jet. Equipment often spills not only onto the hands, but also onto the clothes and feet of those standing nearby. I recommend solving the problem using a tap and a small hose.

I drill holes in a five-liter bottle to add water. I make a hole in the bottom, the diameter of which coincides with the connecting piece. I screw a locking mechanism with a thin tube into the drive. I fix the structure to the post or trunk using self-tapping screws.

Source tel.co.ua

A bottle washbasin with tap works the same as a traditional model. I pour water into the eggplant. If I need to wash my hands, I open the valve. The moisture comes out through the hose, and a person can control the direction of the stream. For the device to function properly, the locking mechanism must move smoothly.

Method using a sponge

The manufacture of this drip irrigation system is the simplest of all those proposed. It is enough to pour water into the bottle, and instead of a cork, stick a piece of foam sponge of the appropriate size into the neck.

If water seeps through the sponge very much, try taking a larger piece of foam rubber. By experimenting, you can achieve the desired intensity of watering.

After this, we place the bottle near the plant, so that the neck with the sponge is located near the root of the plant. As the sponge gets wet, excess moisture will drip to the root, providing water to the plant.

The advantage of this “system” is its ease of manufacture. The disadvantages include the impossibility of accurately adjusting the intensity of watering, rapid water consumption and the need to disassemble the structure for filling.

Cell decor

Each cell of the organizer needs to be decorated. You can use self-adhesive film, wrapping paper, or print your favorite design through a printer. Trace the bottom blanks and cut out decorative elements. Carefully glue them onto the cardboard. Let the glue dry.

Wrap the cell blank in paper and mark the desired height and circumference with a pencil. this way we will get the required dimensions to cut out the colored paper to decorate the cell. Draw lines along the marks and cut out the workpiece. Cover each cell. When the glue has dried, cut out strips of glitter paper about 1 centimeter wide and cover the top edge of each cell with them. Drain the bottoms and rings together in pairs - the cells for the organizer are ready

Grow onions in a plastic bottle

Create a versatile vertical bed for fresh herbs. Cut off the neck of a large plastic bottle and make holes in the body (not too low). Fill the soil up to the first hole, cover them with bulbs inserted with roots inside the bottle. Continue filling the soil. Fill the entire container and place it on a tray. Don't forget to water and harvest fresh greens.

plodovie.ru

Make a system for growing seedlings

It’s not enough to just pour soil into a jar and stick the seeds in there. They still need to be germinated. For everything to sprout, make drainage holes in plastic jars, fill the containers with soil and plant the seeds. Place the jars on a tray covered with small stones or pebbles. Cover with cling film to make a mini greenhouse. The high-speed system for seedlings is ready.

fresheggsdaily.com