How to light a light bulb without electricity: simple and effective ways

If there are no power lines nearby, the cost of connection is too high, or there are other problems, you can make lights in the garage without electricity. There are several options that differ in implementation features and materials; it is worth considering them all and choosing the one that suits best.

And without electricity, you can get bright light in the garage.

What is better not to do

Solar panels

They can be called a modern method that can really bring results.
But if you use solar panels in a garage, it can be called a disaster. Let's just remember how much average batteries cost now; to light a garage and get electricity for certain work, you will have to pay about 5 thousand dollars for their purchase and installation. This amount is considered unacceptable, even if you are constantly in the garage. They also need to be constantly wiped from dust and their condition monitored. And of course, there is a very high probability that they will simply be stolen.

Wind turbine for garage

The method is good, but only in those regions where there is a strong constant wind. To generate electricity to operate devices, you need a wind of 6 m/s. A light wind can provide illumination, but there are easier ways.

Solar lanterns

Here we will simply write down two main disadvantages:

The light is dim.
You constantly need to take it outside to charge, they also quickly break down.

Related article: How to properly make a wooden floor in a bathhouse with your own hands?

Solar lamp

To make the device, you need an old table lamp with a stand, lampshade, scissors and gloves to protect your hands. So what to do:

Cut the wire from the base of the lamp. Unscrew the cartridge from the top and remove the cord; it must also be cut off from the cartridge.
Remove the metal bracket from the base and screw the socket without a cord to its original place, then put the lampshade on it. Make sure that the lampshade fastening is tight and you can unscrew the lamp with solar battery from the stand leg.
Screw the lamp onto the lampshade socket so that the solar panel faces upward.

If the lamp does not fit tightly or is wobbly, you need to fill the gap with a foam sponge, but not for washing dishes, but for bouquets - such sponges are used by florists. They sell sponges in flower shops, they cost about 50 rubles.

That's it, the lamp for evening gatherings without electricity is ready. The lamp will accumulate solar energy during the day, and in the evening it will provide enough light for dinner or even household chores. You can make several lampshades and place them on the veranda around the house. The peculiarity of a solar battery is the ability to accumulate energy even at low light intensity during the day.

The popular bookmaker has launched a mobile application for Android, you can follow the link absolutely free and without registration.

How to make an electronic repeller and windmill from moles and birds with your own hands

Alternative sources of home heating without electricity and gas

Switch light problem

The most common question is “Why do LED bulbs continue to light when the switch is off?” people are using illuminated switches indoors. A miniature neon light bulb (sometimes an LED) located inside the housing does not affect the operation of the lamp when the light source is an incandescent or halogen lamp. If you screw an LED light bulb into a lamp, it will often continue to burn dimly even after the voltage is removed.

Why this happens becomes clear if you carefully look at the diagrams for turning on a light bulb through an illuminated switch, given below. From the diagrams it follows that at load L1 after turning off the lighting there is still a small potential that penetrates through the circuit of the neon light bulb (Fig. 1) or LED (Fig. 2) HL1. In some cases, this is enough to start the LED lamp power circuit. As a result, the switched off LED lamp does not go out completely. It either glows faintly or glows at half-glow, or flickers spontaneously.

Designations on the diagrams:

HL1 – LED or neon backlight;
D1 – diode limiting reverse voltage;
L1 – LED main lighting lamp;
S1 – illuminated switch.

There are three ways to fix this problem:

Replace the existing switch with a regular one or remove the backlight from it yourself.
Install a resistor (Fig. 3) or capacitor (Fig. 4) in parallel with the load. The radio element can be placed in the distribution box, in the lamp socket itself, or on the back of the switch if both the phase and neutral wires pass through it. In the first case, you will need a resistor R2 with a nominal value of 50 kOhm and a power of 2 W or a power of 0.5–1 W, but with a resistance of 1 MOhm. The compactness and low cost of the resistor, in this case, is an undeniable plus. But there is also a negative point - active power consumption and slight heating. The second option with capacitor C1 is free of the negative moments of the resistor and is able to compensate for network interference from other electrical appliances in the room. Installation requires a non-polar capacitive element. It is recommended to use a capacitor with a capacity of 0.1 to 1 µF, capable of withstanding a voltage of 630 volts.
Removing the barely noticeable glow of several LED lamps is not difficult if they are powered from one switch. To do this, one of the LED lamps must be replaced with a low-power incandescent lamp. The tungsten filament will act as a shunt resistor, allowing harmful current from the backlight to pass through it. As a result, none of the lamps connected in parallel will light when the switch is off, since there is not enough current to ignite the filament.

Car vacuum cleaner Shunzao

A tiny but very powerful vacuum cleaner: the black version has a suction power of 12 kPa, the white version has 7 kPa. Works up to half an hour on one charge.

The difference is in the motors. The more powerful one is equipped with a brushless one, the weaker one is equipped with a regular one. Despite the small cup of 100 milliliters, it is a serious helper.

Price: 3,100 2,450 rub.

Lighting a burnt out lamp

In this circuit, when the lamp burns out, the double pins at the ends are shorted together.

Select components depending on the lamp power, based on the plate below.

If the light bulb is intact, the jumpers are still installed. In this case, there is no need to preheat the coils to 900 degrees, as in working models.

The electrons necessary for ionization escape out at room temperature, even if the spiral burns out. Everything happens due to the multiplied voltage.

The whole process looks like this:

initially there is no discharge in the flask

then the multiplied voltage is applied to the ends

Due to this, the light inside instantly lights up

then the incandescent light bulb lights up, which limits the maximum current with its resistance

the operating voltage and current gradually stabilize in the flask

the incandescent light bulb dims a little

Disadvantages of such an assembly:

low brightness level

increased pulsation

And when feeding fluorescent lamps with constant voltage, you will have to very often change the polarity on the outer electrodes of the bulb. Simply put, turn the lamp over before each new start.

Otherwise, mercury vapor will collect only near one of the electrodes and the lamp will not last long without periodic maintenance. This phenomenon is called cataphoresis or the entrainment of mercury vapor into the cathode end of the lamp.

Where the “plus” is connected, the brightness will be lower and this edge will begin to turn black much faster.

This is especially noticeable when installing LB lamps in cold rooms - garage, barn, corridor, basement. If the bulb is not warmed up, it may not even start.

In this case, you just touch it with a warm hand and it immediately begins to burn.

Therefore, remember - a fluorescent lamp is an alternating current light source. Constant is contraindicated for her and kills the lamp. Especially imported ones die very quickly.

Another disadvantage of such diode circuits, which few people talk about, is the resulting current consumption from the outlet. For a 40W LB light bulb with not ideally selected components, the current consumption from a 220V network can reach up to 1A.

And this even exceeds the load of a conventional incandescent lamp of 200W. This is the savings you'll get!

Therefore, which method is right for you, decide for yourself, based on the spare parts at hand and knowledge of electronics.

Regulatory requirements

Regarding the installation of backup lighting in service and utility rooms, there is a set of documents PUE and other regulatory documents.

In accordance with these documents, when installing an emergency lighting network, several basic rules should be followed:

A service or utility room must be equipped with at least two backup lamps. This is necessary in case one of them fails or fails.
Backup lighting devices must be located along the entire evacuation route, providing a minimum illumination level of 1 Lux.
Backup lamps should be located at a distance of no more than 2 meters from such critical breaks in the topography of the room as the beginning of a flight of stairs, corridor turns, doors, control rooms, etc.
Every exit, staircases, and toilets must be equipped with a backup light.

Of course, such strict rules are not necessary when installing backup lighting at home. There you can act according to your own ideas.

DIY garage lighting

Arrangement of a garage includes the organization of high-quality lighting. Depending on whether any work is being carried out in the room or whether it is simply a place to keep the car between trips, it is necessary to ensure full lighting in the garage or limit it to minimal lighting.

How to make light in the garage: lighting options

The power (energy consumption) of lamps and their quantity directly depend on the method of obtaining energy. When an external electrical network with unlimited consumption is connected to the building, there is no need to save on the power of lamps and their number. If you plan to have autonomous lighting in the garage, you must count on the permissible power consumption from a battery or an alternative source (wind generator, solar panels, etc.).

Working in a closed, unheated (lowly heated) and often damp room requires light sources to:

high luminosity with minimal energy consumption;
strength, resistance to accidental impacts and shocks;
resistance to moisture, dust, temperature changes;
Possibility of stable operation at unstable voltage;
compliance of the input voltage with standards for centralized and autonomous power grids (220/380 V).

When choosing a lamp, the intensity of the luminous flux per 1 W of power is taken into account. The leaders in this parameter are LED models.

Other parameters of light sources are also taken into account (the table shows a comparison for lamps with a luminous flux of 800...900 Lm)

Important: at low temperatures (less than -5o Celsius), fluorescent lamps operate unstable, and insufficient voltage in the network also creates a problem. For halogen lamps, protection from dust, touches and voltage surges is required.

They are connected via a power supply (12 V)

For halogen lamps, protection from dust, touch and voltage surges is required. They are connected via a power supply (12 V)

They are connected via a power supply (12 V).

Thus, lighting a garage with LEDs is the safest and most practical, but not the cheapest, option.

Work areas: how to get the garage lighting right

Work indoors is conventionally divided into three or four main groups:

general – requires basic lighting from above;
on a workbench or desktop - local illumination with directional radiation;
at the level of the middle/lower part of the car for repair work, vehicle washing - diffused or directional lighting is required at a height of 0.5...1.2 m;
in the inspection hole there are local light sources directed upwards and forwards.

Alisa compact compressor

Compact but efficient air pump designed to work with bicycle and car tires, as well as inflatable toys.

Indicates pressure, selects the appropriate one, and also knows how to release it from containers. Powered by 12V cigarette lighter socket or built-in 18650 batteries.

Price: 4,100 2,900 rub.

How to choose the power of an energy-saving lamp

Such a lamp starts up instantly, in contrast to the long blinking and flickering of the usual LB and LD models.

What are the disadvantages of this connection scheme? Firstly, the operating current in energy-saving lamps at equal power is less than that of linear fluorescent lamps. What does this mean?

And the fact is that if you choose a housekeeper of equal or less power than the LB, your board will work with overload and at one point it will go boom. To prevent this from happening, the power of boards from housekeepers should ideally be 20% more than that of fluorescent lamps.

That is, for a 36W LDS model, take a board from a sweetheart 40W and higher. And so on, depending on the proportions.

If you are converting a lamp with one choke into two bulbs, then take into account the power of both.

Why else do you need to take it with a reserve, and not select the CFL power equal to the power of fluorescent lamps? The fact is that in unnamed and inexpensive CFL light bulbs, the real power is always an order of magnitude less than the declared one.

Therefore, do not be surprised when you connect a board from a Chinese housekeeper for the same 40W to the old Soviet LB-40 lamp, and you end up getting a negative result. It’s not the scheme that doesn’t work – it’s the quality of goods from the Middle Kingdom that does not correspond to the “reinforced concrete” Soviet guests.

Lighting selection factors

People enter the garage for many reasons and for different periods of time. But in any case, every time you visit a room you need to be well oriented in space and see all the elements.

To create high-quality lighting, the following factors must be taken into account:

Room parameters

(height, area, width);

Work area location

;

Required lighting power

per 1 sq. m;

There are also many technical characteristics that an electrician takes into account when laying wiring. A competent lighting design must meet the following indicators:

Low power consumption;

Long service life;

Even light distribution

The most difficult and important factor is ensuring the proper level of security. All wires must be grounded, properly insulated and protected from contact with owners. Violation of any one of the rules may result in electrical injury or death.

Different lamps create different shades of light

Lifehack for the de-energized: turning off the lights now doesn’t bother people

News

08:24 “Jelly” business of grandmother and granddaughter - in Armenian Lori they make sweets even for diabetics
07:58 It will rain all week in Armenia
23:59 The battlefield is Iran: a big game is underway, from the nuclear deal to ballistic programs
23:48 US seeks to reduce tensions with Russia - Psaki
23:37 Viewers have stopped watching the Oscars - the film award rating is rapidly falling

All news

The network was blown up by a video with a real trick: users decided that after such a miracle, the hated power outages and blackouts will now become a simple matter to them.

However, the matter concerns precisely the light bulb - the most ordinary, economical one. It would seem that a trick with a light bulb can help if the electricity is cut off and there are no candles at home. But, apparently, a candle can be lit with “God’s help.”

Network activists were shocked by how the heroine of the sensational video made a light bulb burn using an ordinary glass of water. It was enough to lower the base of the light bulb into the water - and the burning candle was ready.

While some representatives of the virtual community cheerfully comment on the video, other users express skepticism and invite people to first check the truth of the miracle, and then express delight.

Source

Review of causes of glow

What to do if the LED lamp is on? There are several reasons why, after turning off the lighting device, the LED lamp continues to burn, even dimly or weakly:

poor-quality insulation in a section of the electrical circuit or any other electrical wiring malfunction;
the switch to which the LED lamp is connected is backlit;
low-quality emitters are used in the design of the lighting source;
special functionality of the lighting element.

Is this glow dangerous? This problem does not pose any danger to the wiring, but the service life of LED bulbs will be noticeably reduced if they constantly flicker or glow dimly.

If the switching device is in the off position, and the emitter still glows and burns, then it is best to check the last three factors first. This is explained by the fact that it is very difficult to find weak insulation areas in electrical wiring.

In order to do this, it is necessary to create special conditions, as a result of which a high voltage is applied to the circuit for one minute to cause a breakdown. The section of the circuit that causes the lighting element to glow after the switch is turned off will need to be opened. Moreover, if the electrical wiring was installed in a hidden way, then opening it will lead to damage to the integrity of the wall.

It is important to know! There are many situations where when LED light sources are connected to a backlit switch, they function differently. This occurs due to the fact that the lighting element, which is installed in the switching device, closes the circuit and, accordingly, passes a small current

This is what charges and allows the light bulb to glow when the switch is off.

Another problem why an LED lamp glows in the dark is the low cost of the product. If you purchased a poor quality LED light bulb, this can also lead to a similar phenomenon. This is due to the fact that there is some kind of error in the board. But it also happens that the emitter burns dimly due to the fact that it has its own peculiarity in the functioning of the structure.

We are talking about the processes that occur in capacitors when a load is applied to the lighting element. When electric current passes through the circuit, the capacitor stores energy, and then after the load is stopped, it continues to keep the elements glowing.

Another fairly common reason why LED lamps glow when the switch is off is incorrect connection. You can learn more about this from the video:

Design feature of the LED lamp

The second most common reason why an LED lamp lights up dimly when the switch is off is hidden in its driver. And this is not surprising, because every manufacturer of LED products uses dozens of types of driver circuits, constantly changing and improving them. But often such changes are made with one goal - to reduce the cost of the finished product. But as a result, due to the use of low-quality components and errors made when assembling the driver, the LEDs remain lit even when the lights are turned off. Such a malfunction does not reduce the service life of the LED lamp, but it cannot be eliminated.

How to light a room without electricity. Solar lights for garage and shed.

Many people have a dacha or house in the village. And of course, there are outbuildings such as a garage or shed for storing a variety of tools, gardening equipment, and more. And it happens that it is not technically possible to illuminate these rooms.

It's the 21st century and of course there is electricity everywhere. Maybe there is, or maybe not. Or there is no way to bring him to this or that building or room.

Both the barn and the garage

If a garage or shed is attached to the house, then the issue can be easily resolved. It is easier to run wires and connect electricity from the main room. But if the outbuilding stands alone, separate from the main building. At a distance. Moreover, without windows, and the light from the doorway is not enough to illuminate the far corners of the barn or garage, then what to do?

In this post I’ll tell you how I implemented lighting in my dacha. In an ordinary village, an ordinary wooden house with a barn attached to it. Of course, I installed electricity there, but it still happens that late in the evening you need to look there when it gets dark.

But that rarely happens. But here’s a question about the day, when you’re scurrying here and there, busy with housework, sometimes taking a shovel, sometimes a pitchfork, sometimes an axe. Firewood for the fireplace or fireplace should be brought into the house for the evening. And all the time I have to turn on the light to illuminate the far corners of the barn where the light from the doorway does not reach, but sometimes I forget to turn it off and the light bulb wastes electricity in vain.

ET bottle To implement this idea, I needed empty plastic transparent bottles. I took it from a mineral water bottle, it’s the best. They were filled with water, but not just pure water, but diluted with vinegar. About one and a half liters of water, one hundred grams of vinegar. You can also use chlorine instead of vinegar.

These additives are needed to ensure that bottled water does not bloom over time and remains clear all the time. And so, I poured water into the bottle, but not to the very neck. I didn’t add three fingers to the plug. Left room for water to expand when it freezes in winter.

I’ll say right away that it has been tested by time, the bottle can withstand the freezing of water in winter and does not burst. Now I’ll tell you why we need a bottle of water. This is an additional source of light in dark areas of the barn.

Installation

Next, I identified the place where I needed additional light. And he used a drill to make a hole in the roof of the barn. Thus, I marked where I would cut out a hole with the diameter for the bottle.

Then, armed with a marker and a jigsaw, he climbed onto the roof, and in the marked place, drew a circle the size of the one removed from the bottle and cut out a hole. I’ll say right away that the roof of my barn is covered with tin, so there were no problems with cutting.

The markings must be as precise as possible, and the cutting must be as even as possible so that the bottle fits tightly into the cut hole. I sanded the edges to avoid any sharp burrs. So that they, in turn, do not cut through the bottle.

Then I inserted the bottle bottom down, approximately to the middle, well, maybe a little lower.

All. Almost everything is ready. All that remains is to go around the sealant in a circle to fill all possible holes.

That's all. Everything is holding up very well. Doesn't fall out. Now in the place where it was very dark in the barn, it became much lighter. You no longer need light from a light bulb. And this is in cloudy weather. And when the sky is sunny and the rays fall directly on the bottle, the light scatters and illuminates like a light bulb. Almost.

Saving

The savings are obvious. No need to use electricity. You wonder if the light in the barn has been turned off. You are no longer afraid that the light bulb will be on all day and waste electricity if suddenly I don’t need to go there.

I'll be honest, without exaggeration. This life hack works and is very effective.

What to consider when choosing an autonomous source of electricity?

Many areas of the country, no matter how surprising it may sound, are still not connected to the general power supply system. Others suffer from constant power outages. If there are no power grids in the region, and it’s time to start building a house, what should you do: wait until the site is connected to the network or look for alternative solutions ? What to do if the electricity goes out in the evenings, sometimes during the day, and often completely unpredictably? Contemplating the starry sky and warming up food over a fire is, of course, romantic, but it’s already difficult to live without a refrigerator, a light bulb, a pump and other benefits of civilization in the countryside.

Sooner or later, everyone tries to find a way to connect electricity to the site. There is no universal formula for choosing the best source, since a lot of factors need to be taken into account:

the size of the country house, the regularity of its visits, the usual and maximum number of people staying in it;
number of devices consuming energy. It’s one thing if it’s a couple of light bulbs, a socket and a kettle. It is much more difficult to solve the issue of power supply to a country house if there are many powerful electrical appliances in it, ranging from several televisions and a refrigerator, ending with water heaters and pumps;
features of the region. In windy regions, an expensive, at first glance, windmill will be the most economical and quickly payback source of electricity, but in the Moscow region, for example, wind will no longer be such a profitable source of energy;
availability of electricity. If there are no power grids at all in the region, and their construction is unlikely to be expected, experts recommend using two sources of autonomous power supply. This advice can be ignored if you rarely appear at the dacha.

Naturally, before choosing the type and power of an autonomous source of electricity, you must carefully calculate the amount of energy consumed . The number of electrical appliances and the characteristics of energy consumers are taken into account. The total power is obtained by adding the needs of all household appliances and equipment. It is better to add 15-30% to the obtained value in order to be on the safe side and not be afraid to turn on a new device. It should be remembered that to ensure maximum longevity, it is better for the generator to operate at 80% of its capacity.

Lighting without electricity. Alcohol burner

An interesting option for cooking and lighting is an alcohol burner. The simplest version of such a burner can be made from two aluminum cans of cola, beer and similar drinks.

Two bottoms are used. A series of holes are punched around the perimeter of the collar of the upper part. It is advisable to arrange them evenly. If there is no rush, it is better to mark everything beautifully according to the template. The holes themselves should be small. So, they are made with a needle, a thin awl or a nail. A round hole is punched in the middle of the lid to fill and drain fuel. In the working position, this hole is covered with something. For example, a short bolt. So, first they find a suitable plug, and then punch a hole under it.

The two parts of the can move towards each other. It is a good idea to seal the connection. On a hike, this can be done with a small amount of resin. If you act carefully, you can fit the jars so tightly that they will not allow vapor to pass through, without any sealant.

Thin cans will burn out soon enough. So, if you have a choice, use large jars, liter or 0.75. Some types of beer have these. They have noticeably thicker metal, which significantly extends the service life of the burner.

Alcohol is poured into the burner. About a third or half the volume

It is important not to overfill so that there is room for gas formation. It is not the fuel itself that burns, but its vapors

It's much more efficient this way.

In addition to alcohol, kerosene, gasoline and other flammable compounds are used as fuel. The gasoline they use is not pure. Due to too active evaporation, it may burst into flames. You need to add turpentine or white spirit to it. Turpentine can be obtained from oleoresin.

Obviously, under normal conditions, only alcohol is used. The stench from burning kerosene and especially gasoline and diesel fuel does not go well with cooking. For illumination - it will do. But they try to combine these moments. People switch to alternative fuels in extreme conditions when there is no alcohol.

Before lighting the burner, it is heated by moving matches along the bottom. It is necessary for evaporation to begin. Then bring the flame to the burner. It burns perfectly, like gas on a kitchen stove. Gives heat and light.

Sources

Of course, you can hang a warehouse “Ilyich light bulb” of 20 watts and at least be happy about that. However, modern people love comfort; it has already become an integral part of life. And we will no longer be satisfied with such simple and not very functional tools. Therefore, let's choose lamps that will help organize the room well. For creativity, so to speak, you can light candelabra with paraffin candles, but such romanticism is unlikely to be appropriate in most everyday situations. So, you need a lamp. You need to choose it, and for this you need to know in general what they are and how they differ.

Therefore, let's divide the lamps into two groups. That is:

using a centralized network;
without electricity.

Battery-powered LED bulbs

Recently, you can find LED light bulbs on sale, which differ from ordinary ones in that they have a built-in battery. In the event of a sudden power failure, these types of bulbs will continue to work for some time.

The base of such lamps is normal, standard E27. In terms of its dimensions, such a device will fit most lamps. On the side wall of the device there is a lamp operating mode switch: normal, emergency, or accumulating.

With the help of LED lamps of this type, you can easily equip any emergency lighting scheme for your home. The choice will depend only on the amount you are willing to spend on such an undertaking.

Torch

One of the primitive means of providing light is, of course, a torch. A certain handle and a flammable element, a composition on the knob. The torch handle must be made of wood. The metal will become hot and it will be impossible to hold it, even through a rag potholder. The plastic will float and melt. So, just wood. Affordable and practical.

The simplest torch is a piece of coniferous tree root. The root is dug up and cut to the required length. The end is split into sectors with a knife. They set it on fire. Due to the porous structure and abundance of resin, such a primitive torch burns well and for quite a long time.

A slightly more complex torch is a taiga candle. All sorts of dry kindling and pieces of pine resin are pushed into the split at the end of the branch. The other end of the stick is sharpened. The candle is lit from the flame of the fire. The sharp end is stuck into the ground. It can burn and give light for a long time while you add pieces of resin.

A more civilized torch has a wooden base and a natural fabric or rag wound around the end. The fabric is impregnated with some kind of flammable composition:

petrol
kerosene
alcohol
fuel oil
machine oil
resin
vegetable oils

Causes

What should I do if the LED lamp glows when the switch is off? "RadioKot" is a forum dedicated to electronics, contains a lot of useful information on this topic. According to forum members, there may be several reasons for the weak light after switching off.

Incorrect electrical wiring connection.
The switch has neon lighting.
The LED lamp turned out to be of poor quality.
The LED lamp has additional options (slowly extinguishing lamp).

No. 3. Wind generator for a summer residence

Another free source of electricity is wind, but, like the sun's rays, it is inconsistent. The main advantages , as with photocells, are the absence of the need to constantly purchase fuel and the environmental friendliness of the resulting energy. Disadvantages : high cost of the design, the need to install not only the wind generator itself, but also additional equipment (inverter and batteries with controllers).

Two types of wind turbines are installed in dachas today :

The main question facing those who decide to install a wind turbine is not even its type, but its power. When answering the question, it is worth taking into account the energy generated, accumulated and consumed . Therefore, it is important to calculate how much energy is consumed, for example, per day, what is the average and peak load. It is necessary to take into account the average wind speed, the number of days when the wind speed is above 5 m/s (the most favorable), as well as the maximum duration of calm weather.

In practice, it turns out that weak winds of 2-3 m/s do not provide enough energy. Therefore, experienced summer residents advise stocking up on high-capacity batteries in order to accumulate the energy received on windy days and use it during periods of calm and weak winds.

Lamp from a can

The simplest option for making a lamp, accessible even to kids. By the way, if you involve children in the activity, it will be more fun. What to do:

find a jar of any shape and size, the main thing is that it should not have cracks;
wash the jar and wipe dry inside and out;
wipe the inner surface with strong alcohol or vodka, wipe with a cotton pad, covering the entire surface, including the bottom;
the thicker the layer of alcohol, the longer the jar will glow;
take luminescent paint of any shade and a brush;
apply strokes, dots, strokes of paint to the inner surface of the jar, without covering the surfaces with a continuous layer;
let the compositions dry, pour glass balls or beads inside the container to reflect light.

Now all that remains is to enter a dark room with the can and make sure that the lamp is working. The beads shimmer, creating a reflection, and the result is real magic. You can make a dozen of these cans, and then organize evening gatherings, a disco or something else funny and cheerful. If you place unusually shaped containers around the area, guests and children on the veranda will be delighted.