How to simply make a bar stool out of wood with your own hands according to the proposed drawing with standard dimensions

The layout of individual apartments is always different, as is the area, and often this applies specifically to the kitchen. The size of the kitchen may be familiar (several squares), but often this room is converted into a studio. Be that as it may, a bar counter is installed in such kitchens; it not only looks stylish, but is also practical - today, few families find themselves together at the table. And if there is a counter, then you also need bar stools. How to make a bar stool with your own hands?

Making a bar stool with your own hands

How to make a bar stool with your own hands

Why on your own?

Of course, we are not saying that you should forget about furniture stores and instead make all your furniture yourself. But if you look at the photographs of bar stools that can be found in numerous catalogs of furniture stores, you can conclude: you can actually make such a chair yourself !

Bar stools are easy to make with your own hands

In addition, pieces of furniture made by yourself can become a true decoration of the home, pleasing not only the eye, but also the soul.

On a note! In this case, there are also more possibilities, since you decide for yourself which option is best suited for the interior of the room. There is no need to mention once again about people who like to work with their hands.

Original bar stools

DIY folding chair drawings

Do-it-yourself folding chair, drawings, photos, videos and description of a piece of furniture for lovers of relaxation, which quickly folds and unfolds.
The variant of the folding chair under consideration consists of the following elements:

1. Back and hind legs.
2. Front legs.
3. Seat.
4. Axis of rotation of legs.

BACK AND HIND LEGS.

We will make the legs from a 14x2 (mm) seamless pipe (alternatively, the pipe can be bent with a manual pipe bender). We drill holes in the pipe for attaching the backrest and the rotary axis. We weld the seat supports to the pipe, and close the ends of the legs with wooden or plastic plugs. We will make the back from moisture-resistant plywood 8 (mm) thick and connect it to the pipe with three screws.

We make it from the same pipe as the rear legs.

We will make it from moisture-resistant plywood, 15 (mm) thick. At the bottom of the seat, we fasten metal brackets with screws: two rotating and one guide.

Can be used: screw connection (screw, washers, nut); metal rivet; pin with external locking rings.

Description of the presented model.

The front and rear legs are connected by a rotating axis. The seat rotates inside the swivel brackets and is secured with a guide bracket.

The chair is assembled.

The chair is disassembled.

If the chairs are equipped with a collapsible table, you can comfortably dine outdoors, away from home.

Source

We decide on the structure and design

First of all, decide on the size of the chair. Its height, for example, will depend on the height of the bar counter itself. Also remember that your bar stool should not only be attractive, but also comfortable in all aspects. Once you have decided on all this, proceed directly to the design.

Bar stool with adjustable seat height

To be honest, you can start with the appearance, but then it may turn out that due to ergonomic features some adjustments are required.

Simple wooden chairs without backs

As for the design, first of all, decide how many legs the chair will have and whether there will be any at all. The best option is a product with four legs . It is easy to manufacture, convenient and reliable.

A chair with four legs is more reliable and easier to make

Important! A chair with a back will be even more comfortable, especially if you add armrests to it. If you plan to sit on such a chair during meals, then think about the backrest in advance.

Chairs with backs are more comfortable

Pay special attention to the upholstery (if it is planned). A chair made entirely of wood will fit perfectly into almost any interior, and after varnishing/painting it will also look good in other cases.

Preparation

First you need to understand that this design is nothing more than a rather high stool with a footrest. The principle of assembling a chair will be the same, no matter how you want it.

At Annihaus you can also buy original designer bar stools for your home. Large selection and short production times.

It can be very light or made of materials of quite impressive sizes. Such a chair can be made with both square and round legs, the essence of the assembly of the structure as a whole will not change.

The first step is to create the design of the future bar stool.

One of the important components of this design is the height of the chair legs. They should be of such a height that at least 30 centimeters remain on the bar countertop.

More details about bar stool height

Nothing is known about the creator of the first bar stool. One can only guess that it first appeared around the time when, instead of the usual partitions between visitors and the seller, high (1.1-1.3 m) counter tables with comfortable tabletops began to be used. Visitors to drinking establishments no longer had to leave such counters.

As a result, an ordinary “tripod” chair was transformed into a bar stool. For more noble bars, they were made from valuable wood, trimmed with leather and fabric; the poor public was content with cheap options. But even despite their practicality and high “stature”, all types of bar stools remained in the shadows for a long time due to their lackluster design.

Standard height of bar stool and counter according to GOST

GOST 17524.2-93. Furniture for catering establishments. Functional dimensions of seating furniture .
Downloadable file (click the link to open the PDF in a new window). GOST 17524.2-93

Everything changed in the fifties and sixties of the last century, when high chairs became fashionable and attracted the attention of large enterprises. Much has changed since then, today the designs are very diverse: there are models with and without armrests, with backs, rotating and static, soft, with removable pillows and without upholstery... Changes have also affected the material of manufacture - now they use not only wood, but also chrome, aluminum, plastic. And the variety of decor allows you to use it for all possible stylistic solutions!

Despite all this, when choosing a bar stool, its convenience is of great importance. Due to the center of gravity, which is shifted forward (the visitor rests his elbows on the counter), the support is not the back, but the footrest. For this reason, the backrest is more a tribute to tradition than an ergonomic condition.

As for the seating height, it, as noted earlier, depends on the height of the bar counter, and therefore modern chairs are either produced in two sizes (Th and Bh), or are equipped with a gas-lift mechanism , thanks to which you can easily adjust the height seats (within 54-85 cm).

What happens if you choose the wrong bar stools?

Bar counter parameters

Typically, the dimensions of this piece of furniture directly depend on the size of the kitchen or living room. At the same time, there are standard generally accepted parameters.

For example, the height of a free-standing bar counter is usually 1.1-1.2 meters. Very often the counter serves as a dining table. If the countertop is connected to a kitchen unit, it should be up to a meter high.

The width must be at least 30 centimeters. Otherwise, it simply will not be functional. The optimal width is 80 centimeters. If the kitchen is small, then at least half a meter.

As for the length of this element of furniture, it is calculated in each case individually and depends on the number of people who are expected to be behind it at the same time. To make everyone comfortable, there should be at least half a meter per person.

Which tree to choose?

If you are planning to make a wooden bar stool, then remember: it will require about 10 ready-made elements. The same applies to structures made from other materials.

To make your own chairs, it is better to use wood.

When choosing a material, give preference to hardwood (such as oak, maple, beech). In principle, wood is best suited for self-production (although there may be exceptions, which we will talk about later) in terms of the “effort-to-result” ratio. Moreover, wooden chairs will look great in an apartment/house.

The wood for the chairs must be hardwood

Having chosen a suitable drawing or drawn it up yourself, get the materials. Everything you need is sold in construction supermarkets or hardware stores, while you can order the chair parts ready-made in the workshop. If you indicate the required dimensions, they will quickly and inexpensively cut out all the required parts of the structure.

You can order ready-made parts for bar stools in the workshop

On a note! There may be more details - it all depends on the chosen design. In addition, upholstery materials can be added. Also, after assembling the chair, it is recommended to impregnate it with a primer (if it was not covered with paint/varnish) to protect it from moisture.

The design of bar stools may vary

Chairs require additional processing after assembly

But when making a metal bar stool, some difficulties will arise. This option is suitable for craftsmen who are accustomed to working with metal, have all the necessary tools and are able to make all the parts themselves. Additionally, you will need to do some welding if there are no connectors for fasteners.

Making metal bar stools harder

A wooden product, unlike a metal one, is easier to assemble - for this you will need a hacksaw, a screwdriver, self-tapping screws and sandpaper. Of course, the description is very superficial, but it shows the difference well.

Country style bar stools

Bar seat made of profile pipes

Such furniture allows you to most fully create a bar atmosphere in any room. This is the most effective option from a design point of view.

Required tools and materials

This material is also often used in the manufacture of bar stools. In this case, it is better to use stainless chrome-plated steel as a basis. It is preferable to refrain from using plastic or PVC pipes, since their strength is not as high as that of a metal base. In addition to these pipes, the following materials and tools are used when creating chairs:

• construction stapler with staples for it;
• pipe benders;
• mounting bolts;
• Chipboard or plywood sheet;
• drill or screwdriver;
• foam for the seat, upholstery fabric.

Step-by-step instruction

Chairs from profile pipes are made according to the following algorithm:

1. Before starting work, you should measure the height of the bar counter. This will allow you to determine the dimensions of the future table.
2. Initially, you need to make blanks based on metal pipes for the base of the chair. They should be divided into pieces of varying lengths. The diameter is selected based on the maximum possible load on the chair.
3. The upper part of any of the workpieces is bent using a pipe bender in the shape of a semicircle.
4. They are connected to each other with bolts for fastening. This will give the product increased stability.
5. The seat is constructed from plywood sheet or particle board.
6. The diameter is also determined based on the body weight of the people sitting on it.
7. After the seat frame is made, a piece of foam rubber is fixed to it using a stapler, and then covered with upholstery fabric. You should use a material that is highly resistant to dirt and is easy to clean dry and wet.
8. The seat is attached to the place where the metal blanks are fixed. This is done using a drill or screwdriver, as well as fasteners.
9. To build footrests, you should mark the required height on the chair legs. At this level, pieces of metal pipe are fixed, the length of which is equal to the gap between the legs.

Features of making a bar stool

Despite the huge number of ideas (both in specialized magazines and on the Internet), the most important thing in all cases is the correct measurements.

The most important thing is the correct measurements

First, decide what the height of the chair will be. It is recommended that the height from the seat to the tabletop be approximately 35-40 cm. Having determined the height, draw up a drawing or use a ready-made one (choose the appropriate option).

What determines the height of a bar stool?

On a note! To make the simplest bar stool, you will need 4 legs, the same number (preferably) of legs and, in fact, a seat. If a backrest is planned, then the back legs should be about 30-35 cm longer (they will serve as the basis for the backrest).

Bar stools, their features

It is easy to make a mistake at any stage of manufacturing - both when preparing parts of the structure and during measurements. Therefore, it is recommended to double-check all measurements several times before entering them into the drawing or cutting off an unnecessary part.

Check measurements several times when making chairs

The ready-made drawings already mentioned above will help with this, which is more important for people who have not designed anything before. Don’t rush, try not “for show”, but for the result!

You can make a bar stool using ready-made drawings

Photo example of making a bar stool (master class)

Covers for bar stools

The final stage of production will be decorating the product and covering it with soft fabric. The most practical would be to create removable covers, since they can be washed periodically. You can also create a soft seat covered with regular fabric and sew a top, replaceable cover.

The covers are:

• Removable with ties. These are small mats made to fit the size of the seat. They are tied to the legs using ties.
• Fixed, which are pulled over the seat. These covers are made exactly to the size of the seat and are attached to it using an elastic band at the bottom or nailed with small furniture nails. Fastening with an elastic band allows you to periodically remove the cover, which is more hygienic.

Option No1. Simple wooden bar stool

The first thing you have to think about is how will the seat be, hard or soft? If you don't know which option to choose, do a firm sit like the example below. In the future, you can upholster it with any available material (fabric, leather, etc.) at any time. The diagram below shows the design and dimensions.

Scheme of a wooden bar stool with dimensions

Step 1. For the legs, use wood 5x5x71 cm (in our example it is poplar). Reduce the chamfers/angles at both ends by about 5 degrees so that the legs are angled relative to each other. For connections, drill pocket holes.

Making chair legs

Step 2. Attach the bottom/middle strips by chamfering in the same way (all at the same 5 degree angle).

Installation of cross bars

Step 3. Having fastened all the parts that are parallel, start screwing the transverse partitions to one of these sides. Do one side first, then the other.

Fastening perpendicular partitions

Step 4. When attaching the partitions, take into account the fact that it should be comfortable to place your feet on them while using the bar stool. This is a must.

The process of attaching partitions

Step 5. The seat will have a special shape, which will make the chair even more comfortable. Mark the end of the board that will be used for seating. To get the desired shape, use a circular saw, adjusting it to different cutting depths; although it is quite possible to use a regular saw. First, cut the recesses, and then remove the excess wood with a chisel.

Excess wood is removed along the recesses

On a note! The process, of course, is quite complicated, and therefore, if you have something better at hand, you can refuse the chisel. Once done, thoroughly sand all surfaces with a sander.

Step 6. In the end, all that remains is to connect the legs to the seat. For this purpose, drill holes in the upper part of the legs, make the same ones at the bottom of the seat, and then, using glue, place all the parts on the pins.

Connecting the legs and installing the seat

Sand the surfaces of the finished bar stool using sandpaper. If necessary, seal the holes with putty. Next, you can paint the chair or, alternatively, varnish it.

Step 7. That's it, a simple bar stool is ready (and in our example there are three of them). This design - thanks to the proper placement of perpendicular crossbars, comfortable seating and selected height - may well become the most favorite and comfortable place in the house! Would you like to make the same chair? Feel free to get to work, because nothing could be easier!

This is what finished wooden bar stools will look like

Option No2. Backless bar stool with metal legs

Let's look at the process of making a simple chair made of walnut (seat) and metal. An old bed frame was used for the legs. The height of the structure is approximately 64 cm.

A simple bar stool that we will make

A distinctive feature of this option is its shape, which makes it easy to weld and strengthen pieces of metal. If you are planning to use a welding machine for the first time, then in the process of making such a chair you will definitely gain valuable experience and learn how to cook well.

The wooden part is made of walnut

Step 1. Start by creating the shape of the future structure. Cut a suitable material (for example, chipboard) into four parts of 54.5x23.2 cm. All elements are fixed with a side joint using screws, resulting in a square “pipe” 58.5 cm high and sides 20 cm long.

You need to cut 4 identical parts

The result is a square “pipe”

Step 2. Make an angled base for the mold using a piece of 9.5 cm thick board. You will need to cut the pieces at an angle so that they all fit. To do this, find a suitable angle using a tape measure and set it so that everything fits. As a result, after cutting you will get beveled edges.

First, a suitable angle is found

The desired angle is set

You can start cutting

Step 3. Fit the pieces with the edges cut at an angle of 45 degrees around the perimeter of the base part. Attach the beveled base using plywood and small nails, as in the photo below. You do not connect this part to the “pipe”, and therefore it can be easily removed if necessary.

The segments are adjusted around the perimeter

Everything needs to be carefully controlled

The parts are attached with pieces of plywood

Step 4. Thanks to the made shape, you can easily determine the location of the legs. No changes are required, just attach and mark.

Future legs just need to be applied

The first leg is applied

First, mark and cut the legs from the bottom. To make the process easier, you can hang a corner of the base over the edge of the table and then secure the iron piece in place. Then cut off the bottom ends.

The corner of the base can be hung over the edge of the table

The lower end of the leg is cut off

The cut leg is attached

After this, place everything in the mold and begin marking the upper ends of the future legs.

Next, mark the upper ends of the legs

Step 5. For the top of the structure, use 4 corners. Mark everything you need using the square you made earlier. Glue the pieces together, then remove them from the mold in order to fit the weld on each side.

4 corners are used for the top part

The parts are glued together

The parts are now welded together

Important! It is better not to place a vice, as in the photo, on wood. Because the bolts that hold everything together can fly out, and everything will have to be redone.

It’s better not to put a vice on wood

Step 6: Cut some more pieces of metal to make the footrest. In our example, the length was approximately 30 cm and the angle was 45 degrees.

Let's start making the footrest

Ready-made footrest

Step 7. The support with footrest was held with the top of the structure and blocks for the supports. Weld everything together. Weld a metal pad on the bottom of each leg. Upon completion of the work, sand everything with sandpaper (recommended grit - 40).

The support is welded to the legs of the future chair

Metal pads are welded at the bottom

Next, everything is processed with sandpaper.

Step 8. Now it's time for the walnuts. Cut the main part into 2 thick boards and sand them with sandpaper. To sand beveled edges, use sandpaper with a grit size of 100-220.

We begin to make a seat for a chair

Wood cut into 2 parts

The boards are sanded

The wood also needs additional processing.

Step 9. Treat the frame of the future structure with a primer, then with black paint. Finally, attach the wooden seat to the pre-drilled holes using screws.

The seat is installed, the bar stool is ready for use

Video - DIY wooden bar stool

What types of bar stools are there?

At first glance, all bar stools have a similar structure, but this is not entirely true. The differences between them are much greater than they might seem.

Table No. 1. Bar stool designs.

Chairs differ from each other in the type of legs. This is an equally important criterion, on which, first of all, the reliability of the design depends.

Table No. 2. Varieties of legs.

Option No3. Wooden bar stool with round seat

Another great option, but, compared to the first, much more difficult to implement. But first things first.

We are considering another option for making a bar stool

Step 1. First, prepare the necessary lumber. It is better to use a block with a section of 30x30, although in our example we use 30x40 due to the lack of a suitable one on sale. All this will cost a very reasonable amount.

First you need to buy all the necessary materials

Step 2 : Start cutting. Prepare 4 bars 45 cm long, another 4 - 57 cm.

First of all, the bars are cut

Step 3. First of all, make 2 blanks from bars of the “long-short-long” type, then glue 2 more short ones between them. By the way, in our example, in addition to clamps, clamps from a circular saw and a grinder are also used.

A pair of short bars are glued between the blanks

Step 4. Make a milling box from the leftover boards and plywood. It is necessary that the 8-gauge stud goes through the entire rack (although it is better to use larger diameter bolts to minimize vibration). In the example, the stud is tightened with nuts; the workpiece rotates inside the box when the nut is constantly tightened. Ideally, it is better to make a cutter for this, which rotates the blank by 10-15 degrees.

Stages of manufacturing a milling box

Step 5. In the end, you will carve a stand like this.

Turned stand

Step 6. Start making the seat and footrest. They will be round, their diameter will be 31 cm. For greater strength, you can glue them together from two panels, placing the lamellas across each other.

These parts are glued together from two panels

Step 7. Cut a ring from plywood using a router. With this ring you will process the outer edges of the footrest and seat, as well as the inside of the latter.

Using a plywood ring

Step 8. Something like this. The inside was milled using a copy sleeve, and the outside was done using a milling cutter with a bearing.

Photo of the manufacturing process of the seat and footrest

Step 9. Mark the footrest - place the central post in the right place, then trace the outline.

Footrest markings

Step 10. Mark in the corner where exactly the vias need to be made. By the way, a feather drill can “tear” wood; if this happens, you will be forced to putty a lot.

The locations for drilling via holes are outlined.

Step 11. Using a thin drill, mark the point where the pen tip will pass. Next, use a feather drill to make holes of the required diameter, cut out sections with a jigsaw, and then level everything with sandpaper on a block.

Stages of making a footrest for a bar stool

Advice! Experts recommend first making a plywood template and milling out the holes - in this case, you can get a higher quality cut and reduce the amount of work with sandpaper.

Step 12: This is what the wood will look like after filling the gaps left by the feather drill.

Photos of wood before and after treatment

Step 13. Glue the leg blanks from the bars.

Gluing leg blanks

Step 14: Shape them using a plywood template. Be careful and securely fasten the template with nails, otherwise it may be torn off the workpiece.

Plywood template torn from the workpiece

Step 15. Glue the crosspiece, assembled on the grooves, into the seat.

Gluing the cross into the seat

Step 16. Make similar grooves in the legs to assemble them.

Grooves are formed in the legs of the chair

Step 17: After routing the edge, begin assembly.

Finished legs of the future chair

Step 18 Sand the seat with extreme care.

Polished seat

Step 19. Pre-assemble the bar stool (without glue) to try on the parts.

The structure is assembled without glue

Step 20. Connect all the parts together.

Connecting chair parts

Step 21. After final assembly, apply stain and varnish to the glue. The result you get will definitely please you!

This is what the finished chair looks like

Table. The cost of making such a bar stool.

On a note! In general, making such a chair will cost about 1,400 rubles.

Folding chairs with backrest

To make this copy, prepare in advance:

• two bars of legs 74 and 47 cm long, respectively;
• 5-8 flat slats 32cm long;
• 3 bars 43 cm each;
• fastener

Let's move on to the collection. Let's start with making the seat. To do this, mount the slats on the support bars using short self-tapping screws at an equal distance from each other.

Let's move on to assembling the frame. Its main components are the protruding legs and back of our wooden masterpiece. We select the part where the back will be and attach slats to it to support the back; in the lower part, one crossbar is enough for greater stability. The rear legs also have crossbars at the top and bottom.

So, we have two elements that need to be fastened together. To do this, use bolts of any convenient diameter, drill through holes in both frames and fasten them together. We connect the front and back frames of the chair with bolts and nuts.

Advice: do not tighten the nuts too tightly, let the inner frame rotate freely, but not dangle.

You've probably already seen similar photos of a folding chair, and now this convenient and practical piece of furniture will appear in your home.

Option No4. Chic metal bar stool

Let's consider another interesting option for making a bar stool. It looks attractive and original.

Metal bar stool - decoration for your kitchen

Step 1. Draw a pre-prepared shape on a piece of thick asbestos sheet that is used for welding (red lines in the photo).

Applying markings to an asbestos sheet

Step 2. Cut according to the sketch of the workpiece, using a 2.5 cm strip.

Blanks are cut according to the sketch

Step 3. Weld the parts together, as shown in the photo below.

The parts are welded together

Step 4. Select the internal layout. Let’s be clear right away that this stage can take a lot of time. Use the same strip for shredding.

Internal layout is selected

Step 5. Weld the parts and clean them. Also, round the corners.

All elements are connected

Step 6. Proceed to the most important task - start welding the legs. Use a 3x2 cm profile for this.

The legs are welded

Step 7. In our example, the author did everything by eye, that is, he did not make a drawing, did not measure angles, etc.

Leg welding process

Step 8. First, grab the legs at 1 weld point, then gradually move them apart to the required positions.

First, the legs are welded to one weld point

Step 9. This is what you will get as a result.

This is what should happen

Step 10. Mark the level at which the footrest will be located. Try it on yourself, you need to feel comfortable. In our example, this is 45 cm from the seat.

Indicates the level of the footrest

Step 11. To make stops, use the same 3x2 cm profile.

The same profile is used for the stops

Step 12. Make tricky slant cuts for them, then weld them.

The stops are welded

Another photo of the process

Result of work

Step 13. Place special plastic plugs designed for steel profiles on the legs. Although you can, as in the example, make special “heels” from wood: they will also not scratch the floor, but they can be sharpened if necessary to ensure stability for the bar stool.

Making wooden plugs for legs

Step 14. The part of the cork that will fit inside the profile should taper.

Narrowing of the inner part of the plug

Step 15. Such plugs will be held in place only by friction. No glue or screws are needed. Sand the corks to fit the legs.

Ready-made wooden plugs for legs

Step 16. The rough version of the bar stool is almost ready.

Draft version of the chair

Same, top view

This is how the chair will look in the interior.

Draft version of a bar stool in the interior

Step 17. Start painting the product. First, apply a coat of primer.

Primer is applied first

Step 18: Paint everything below the seat black.

Legs painted black

Step 19. Protect the black parts of the structure with something. This way they will not get dirty during subsequent painting.

The black parts of our stool need to be protected.

Legs are wrapped in film

Step 20. In our example, such a cardinal color was chosen for the seat.

Painting the seat red

Step 21. That's it, your DIY metal bar stool is ready for use!

That's it, the metal chair is ready for use.

Video - Another option for a metal bar stool

Video - Original do-it-yourself stool

Photos of DIY bar stools

Tools and materials

The tools we need are:

• pencil, tape measure, ruler (all of these are used to create a drawing and mark the lumber);
• square;
• wood hacksaw;
• sandpaper or sander;
• drill or screwdriver;
• hammer;
• topped up.

The materials that will be used in the work process are::

• lumber;
• fasteners for legs;
• glue;
• self-tapping screws;
• paints and varnishes;
• stain;
• solvent;
• brushes