LED night light: made of LED strip, wood, plywood or plexiglass

Plexiglas has recently found wide application in various sectors of life. Office partitions, advertising products, aquariums and other decorative items are made from it. This material is easy to work with at home. You can purchase it at any building materials sales department.

Good lighting in the house plays an important role in any design decision. An original decoration for your apartment can be a lamp made from plexiglass with your own hands. A little imagination and perseverance - and your room will sparkle with new colors.

Safety of night lighting

As is clear from the above examples, there are a huge number of designer models of homemade lamps.
There are different techniques for working with decorative materials to create a variety of lighting effects. Many home craftsmen believe that compact nightlights have minimal power and low voltage, which in itself should protect against problems. This is not entirely true. A voltage of 12 volts for a halogen light bulb or 3 volts for an LED power supply does not pose a threat to the human body. However, if a short circuit occurs, an electrical arc will form at the point of contact. At the same moment, a current will pass through the wires, which can heat the insulation to the point of fire. In this case, the power supply may operate in overload mode, but the shield will not react. That is why it is necessary to protect the wiring of such light sources with a fuse.

After the electrical wiring at the output of the power supply is protected, you need to pay attention to the electrical safety of the board itself

It is enclosed in a reliable housing, which is especially important for lamps in children's rooms, where children may try to disassemble the night light

Installing the controller

Everything works correctly so I can stick the controller on with hot glue.
Now I can enjoy the beauty of this beautiful structure. This lamp is very simple and at the same time very modern. It was a very interesting and exciting process of creating a lamp. I hope that these detailed instructions will allow you to make your own lamp with your own hands. In continuation of all that has been said, I recommend watching the video instructions for making and testing the lamp. Plexiglas has recently found wide application in various sectors of life. Office partitions, advertising products, aquariums and other decorative items are made from it. This material is easy to work with at home. You can purchase it at any building materials sales department.

Wide selection of luminous furniture made of plexiglass in

Our company offers a wide selection of LED interior and exterior items made of plexiglass at competitive prices:

— LED benches of any size and configuration, which are perfect for arranging adjacent areas of country houses, organizing special events, corporate events, and performances of musical groups;
— luminous tables with functional internal lighting;
— LED cubes – designs that ideally combine coffee (cocktail) tables and lamps;
- luminous multi-color cubic structures, which consist of several elements in the shape of a cube and equipped with backlights of different color shades;
— luminous chairs that harmoniously complement the interiors of cozy cafes or bars;
— LED sofas that add fresh colors to any interior;
— luminous dressing tables that will become a bright accent in luxurious bedrooms and beauty salons;
— LED bar counters;
— luminous coffee tables and acrylic tabletops.

Our professional craftsmen produce high-quality and functional furniture with unique design properties according to standard or exclusive drawings in accordance with the personal requirements and wishes of customers.
You can order original LED furniture made of high quality German plexiglass by calling +7. Date of creation: 06 OCT 2022 Author "Akrilshik"

Plexiglas: what is it?

But let's start with the basics: let's figure out what this material, plexiglass, is. It is also called acrylic, although it can also be based on polycarbonate or polystyrene. The latter is used for the internal needs of buildings; it is poorly resistant to the destructive effects of ultraviolet radiation and precipitation. However, the material is able to “work” in a wide temperature range: from minus 20 to plus 60 degrees.

As for polycarbonate, it is resistant to ultraviolet radiation, and the range of tolerated temperatures is even higher: from minus 40 to plus 120 degrees. Therefore, the material can be used outside.

Plexiglas is similar in quality to polycarbonate. Its operating temperature limit is from minus 20 to plus 70 degrees. For processing, you will need a sanding block and paper - to remove scratches and make smooth edges. Therefore, plexiglass for lamps is a good option.

Important element: LED driver

For the correct operation of a DIY LED device, you need to resolve the issue with the driver. The layout of this unit is quite simple. The operating algorithm consists of passing an alternating current of 220V to the diode bridge through capacitor C1.

The rectified current goes to series-connected LEDs HL1-HL27, the number of which can reach 80 pieces.

The driver for a homemade LED device is assembled according to the diagram below. You can also use ready-made elements bp 3122, bp 2832a or bp 2831a

To avoid flickering and achieve a consistently even color, it is advisable to use capacitor C2, which should have as large a capacity as possible.

What does it represent?

An LED night light is a lamp powered by LEDs. LEDs are capable of converting electrical current into light. And the brightness of the device depends on how powerful the flow is. LEDs gained popularity at the end of the last century and have changed a lot since then. They are used in various areas of life, for example, when installing banners or for designing show programs.

LEDs can be distinguished into several types:

Multicolor - they are based on the optical effect of obtaining many shades by mixing three primary colors. As a rule, this requires mixing red, blue and green, which in different combinations will help to obtain other colors.

Thanks to modern technologies, LEDs can have any color and shape. In addition, they are divided into outdated types and improved models.

Types of lamps

Autonomous LED luminaires

All LED night lights can be divided into two groups according to the method of power supply. These include:

Autonomous. Powered by battery or battery.
Stationary. Plugs into an outlet.

Autonomous products can be moved and placed in any convenient place. The disadvantages include the expense of batteries, which need to be changed periodically. A model that receives electricity from an outlet can only be installed near a power point. There is no need to buy consumables for such a lamp.

Night lights with motion sensor

Wood lamp

Devices can be equipped with various sensors that make them easier to use. They do not need to be turned on; they activate independently. It is not recommended to place such night lights in the room, as they can detect any arbitrary movement and turn on. They are usually installed in closets, garages, and hallways. The sensitivity of the sensor can be adjusted to avoid false alarms on pets. The range of action is 3-5 meters.

Night light made of wood

This type of night light is completely safe. The wood is processed in such a way that there is no release of harmful substances when heated. Wooden LED night lights are even installed in children's rooms, as they are durable, environmentally friendly and difficult to break.

Lighting for home comfort

Why is acrylic edge lighting convenient, and why is this technology used in interior solutions? Firstly, it is beautiful, as it creates a diffused stream of light that is pleasing to the eye. Secondly, it is practical. The use of solutions with this technology allows you to arrange lighting with minimal energy consumption. And thirdly, often only the edge lighting method allows one to achieve the desired decorative and practical effect.

Illumination of acrylic panels is used in home interiors in the following cases:

for illuminating ceiling panels;
to create a false window with backlight;
for illuminating kitchen apron panels;
for illuminating organic glass shelves;
for illuminating staircase handrails made of acrylic;
for creating framelights as decoration elements.

Framelight is a light panel where you can insert posters with images. Posters can depict a painting in any style, landscape or photograph. Its beauty is that the printed image can be replaced, and this is quite easy to do. If such a light panel is placed in a dimly lit area of an apartment or house, then, in addition to its aesthetic value, it also carries a very practical load, creating additional lighting.

Using an old power supply for a night light

Nowadays, so many mobile phones pass through the hands of each family member that you can easily find a couple of different chargers. You can make an LED night light out of them with your own hands. This circuit will be much better than a capacitor circuit:

Ready-made housing with plug for connection to the network;
galvanic isolation from the network - there will be no high-voltage potential at the capacitor terminals;
stabilized values of output voltage and current.

We invite you to familiarize yourself with Traces of bedbugs on furniture

Underwater rocks

A story from practice: the manufacturer indicates on the charger body an output voltage of 5V and a current of 1A (may differ). When I made a night light for myself, I calculated the resistors for the LEDs for this voltage. The night light practically stopped shining after 2 nights. The LEDs dimmed, and the lampshade of the night light was always warm...

In addition, I initially, by mistake, soldered in resistors with a value slightly less than the required 100 Ohm. I became interested in why the LEDs were degrading and I measured the voltage. The charger gave out as much as 7 and a penny volts. Naturally, the LEDs were fed with twice the rated current.

Moral: do not believe what is written, but check the voltage and current of the LEDs with a multimeter.

Look at the diagram of an LED night light from a mobile charger.

As a result, you can get a similar LED night light. If desired, you can hide the diodes with a diffuser from a broken LED lamp.

More details on how to make a night light from LEDs and a smartphone charger are described in the video.

Many phones come with chargers with a USB connector. You can buy ready-made LED modules in USB flash drive format and get a simple LED night light. True, you will not get pleasure from designing, developing and assembling a custom night light.

A night light is the simplest and most harmless device that you can make with your own hands. On the other hand, its simplicity and lack of requirements for brightness make it possible to turn a simple and ordinary thing into a real work of art.

At the same time, you can implement many ideas, such as iridescent colors on an RGB strip, or turning on a night light when there is a clap or depending on the light level. Look at the LED acoustic switch diagram.

Resistor R3 sets the operating point of the transistor and, accordingly, the sensitivity of the circuit

Transistor VT2 is the second stage of the amplifier, and capacitor C2 is electrolytic, pay attention to this

Night light starry sky"

One of the most current and romantic night light models, to one degree or another, imitates an endless cluster of constellations in the night sky. You can make such a light source yourself from scrap materials. It does not need to be connected to the network, because a regular flashlight with little batteries is enough.

To create such a night light, you need a glass jar with a lid of any size, thick foil, scissors, an awl, a small flashlight and any surface that is not afraid of damage, for example, a tray.

Draw a star map on the foil. You can arrange celestial objects schematically or following the real arrangement of stars. It all depends on your desires and level of effort. If you are making a similar night light for a child, you can limit yourself to the image of the constellations Ursa Major and Ursa Minor.
Place the sheet on a flat surface and use an awl to make holes. These will be the luminous stars.
Trim the foil so that its height matches the height of the jar. Roll the sheet into a tube and insert it into a glass container.
Place a flashlight at the bottom of the jar and turn it on. The walls and ceiling will immediately be illuminated by the beautiful glow of the night light.

There is another option to make a children's night light that imitates the night sky. It can be made from an ordinary tin can. Such a container should be cleaned, the label removed, painted in any pleasant color and several holes made with an awl. Inside the jar you need to put a flashlight, a garland or a lit candle. It is advisable to cover the edges of the jar with a plastic lid so that none of the family members are injured.

Decor Tree plexiglass lamp for the Mega Belaya Dacha shopping center

When creating any interior elements for retail space, attention is first paid to the durability of the material, its resistance to mechanical damage and unstable environmental conditions. In this regard, the leading position in recent years has been occupied by acrylic - an economical, durable material that can be easily thermoformed and thus is designed to bring to life all the creative ideas of creative designers.

An important advantage of acrylic is also its decorative appeal - transparency, shine, exceptional light transmission and surface smoothness.

Among the most daring and breathtaking design solutions made from acrylic, it is worth noting installations made from acrylic rods

Additional equipment of such products with powerful LED lighting makes them shimmer with a bright glow, which will not only become an additional source of illumination of the space, but will also captivate the attention of even the most sophisticated viewer

Design of acrylic Decor Tree lamp

The technological capabilities of the AkrylChik company allow us to implement complex design concepts and meet the expectations of the most demanding customers. The project to create an acrylic lamp in the shape of a tree for the second largest shopping center in Europe, MEGA Belaya Dacha, was also no exception.

A transparent acrylic Plexiglass rod with a circular cross-section with a diameter of 15-20 mm was used as the main structural element. To ensure uniform distribution of light over the entire surface of the rods, they were sandblasted. Thus, we have achieved a perfectly matte surface of the acrylic blanks, thanks to which the entire structure of the future tree will create a soft diffused glow, pleasant to the eyes of its beholder.

Thermoforming and bright backlight

By thermal molding of plastic rod blanks, a tree trunk and spreading branches with a total structure height of 310 cm and a crown diameter of 110 cm were formed. The lighting elements are implemented in the form of an open LED strip SMD 2835 120 LED/m with a power supply of 12 V and a degree of dust and moisture protection IP33. The tape creates a powerful, uniform glow with a light output of 125 Lm/W, which, combined with the high light scattering rates of acrylic, gives the wood an incredible glow effect.

At the same time, the original lamp will delight the eyes of shopping center buyers for a long time, thanks to a productive tape with a service life of about 30 thousand hours. The backlight operation is supported by a compact power supply with a nominal connection power of 100 W and a voltage of 12 V.

All elements are integrated into a stand with a diameter of 82 cm. The sliding design of the podium allows for quick and convenient access in case of need for diagnostics or replacement of light sources.

Own design of night lights

Modern stores offer a huge variety of night lighting devices of various designs, for different tastes and at any price.

And not in every case is it financially justifiable to create such devices with your own hands; however, their design gives scope for turning creative fantasies into reality without spending a lot of money. That is why anyone who wants to make their home interior original can create a night light with their own hands.

In the process of designing light, in comparison with basic lighting, where the same distribution of light flux is necessary, the main emphasis is on the competent combination of a number of factors through which visual perception is formed:

device shade;
light refraction, as well as its decomposition into shades;
scattering and reflection of light flow;
combination of colors and visual effects.

A little about the material

The named material is a polymer alloy that has high strength and at the same time maximum ductility (subject to the use of high temperatures). The composition of plexiglass includes amorphous polymers, which mainly consist of unfolded and linear macromolecules. This composition of the material allows us to achieve its absolute transparency, strength and lightness.

A new material that significantly expanded the capabilities of builders and designers

The advantages of plexiglass used as a material for creating decorative interior elements are:

Therefore, organic glass is becoming increasingly in demand among jacks of all trades.

It is worth noting that completely different intricate little things can be created from plexiglass. These can be cute bookcases and fancy shelves, small aquariums or pots for indoor plants, semicircular partitions in the room or simple tabletops. In some cases, it may be necessary to bend the plexiglass at a given angle.

You can carry out this task at home, following the basic rules for working with plexiglass.

Materials for gluing

LED strip is cut through three diodes

The LED strip has a standard self-adhesive backing. But it is not suitable for long-term fixation on rough surfaces, such as wood. The list of materials that can be used to glue the LED strip is as follows: aluminum profile, tape for LED strip, aluminum tape, quick-setting glue. They improve properties and increase fastening efficiency.

Adhesive tape for LED strip

Serially produced tapes are a printed circuit board with LEDs attached to double-sided tape. Its free side, used for installation, is protected by a smooth transport film. For high-quality models, the 3M marking is applied to it.

Acrylic tape 3M for various applications

How to glue LED strip:

Markings are applied to the previously prepared surface.
Wires and a power supply are connected to the backlight contacts or using a connector; install a switch.
Using a sharp object, separate the beginning of the tape from the protective film and release a section 15-20 cm long.
Apply the strip with LEDs to the surface and press firmly.
Gradually freeing sections of the tape from the film, completely glue the tape along the marked path. When making connections in the corners, do not bend it, but use corner connectors or solder it.
Install the power supply in a convenient place protected from moisture.

The tape must be applied accurately to the markings. If it is placed incorrectly after detachment, the tape loses its properties. It will be difficult to reattach it firmly.

Aluminum profile

Aluminum LED Profile

The optimal mounting for LED lighting is aluminum profiles. They are used for extended, powerful models SMD 2835 and SMD 5630, 5730 and for the popular LED-based SMD 5050. For fastening structures with a power of more than 14 W, their use is mandatory.

Profiles can be overhead, mortise, or corner. LED lighting is glued inside the profile, and it is mounted on the selected surface.

Using aluminum profile for LED strip

Properties of aluminum profile:

The self-adhesive surface of the tape fits perfectly onto a flat and smooth base;
Easily and firmly attached to the mounting plane;
the heat generated during the operation of LEDs is removed through the aluminum surface;
The matte diffuser, which covers the front part of the profile, gives a pleasant appearance and makes the lighting softer.

Glue

Super glue is perfect for gluing LED strips

The right LED strip adhesive provides a quick-setting bond. Adhesives cope with this task:

based on cyanoacrylate, called superglue, for example “Moment Super”;
based on rubber or silicone, for example, liquid nails “Titanium” or “Moment Montazh”.

Recommendations for fixing with glue:

Superglue is applied pointwise every 50 - 100 mm. This way the tape is securely fixed and, if necessary, it is easier to dismantle it than when applying a continuous layer of glue.
The strip with LEDs is applied with its base to the surface on which the glue is applied and pressed firmly.

Adhesive joints are used on vertical, inclined porous surfaces. It is resistant to temperature and humidity. The tape adheres to a properly treated surface in 20-60 seconds. They completely glue together in no more than 2 hours. You can use glue to attach the LED strip to metal, wood, plastic, wallpaper, glass.

Aluminum tape

Aluminum tape is used instead of a profile for LED strip

If it is impossible to use the profile of LED strips of low and medium power (6-10 W), they are attached to aluminum or foil tape. Its surface has heat-dissipating properties and can serve as a light reflector.

Aluminum tape for the LED strip is glued to the surface according to pre-applied markings. To ensure a good connection, superglue is applied pointwise to it. Then a strip with LEDs is attached to the tape.

Other mounts

Mounting clip

If the LED strip is hidden or appearance does not matter, you can use the following to fix it:

disposable nylon zip ties;
plastic clamps.

Do not fasten the LED strip using staples with a construction stapler.

Two methods of gluing LED strip have become widespread: with tape and with glue. The tape comes off over time. The strength of this installation is increased by using superglue. It is optimal to mount the lighting using an aluminum profile.

Do-it-yourself illumination of plexiglass with LEDs - Metalist's Handbook

Plexiglas for edge lighting is a beautiful and practical solution for a home, apartment, or office.
Light spreads and refracts evenly through the canvas. Thus, a cozy atmosphere is created in the room.

The drawing on the wall looks organic, not only performing a decorative function, but also illuminating the space at any time of the day.

In the interior, edge lighting is used for several reasons. Firstly, it looks unusual, creating a diffused light flux. Secondly, this solution is practical: it is possible to organize high-quality lighting that consumes a minimum of electricity. And the final argument is the combination of aesthetics and functionality.

Edge lighting can provide a pleasant atmosphere in the home

Canvas lighting is used in tandem with the following designs:

ceiling panels;
false windows or framelights;
kitchen apron panels;
shelves;
handrails of stairs, etc.

Read more: plexiglass apron for the kitchen.

In fact, you can turn any idea into reality.

: "Profile for edge lighting"

From this video you will learn how to make a profile for end lighting.

The design of end lighting in combination with a false window is popular today. Framelight is a panel where a poster with an illustration is placed. Any landscape, photo or painting takes on a new look. In addition to its decorative function, the unique panel creates additional lighting.

The design is delivered ready-made; the user needs to insert a poster with an image. Often, an imitation of the view from a window, different landscapes, or photos are used as a picture.

The poster can be easily replaced at any time. A summer street can easily be replaced by an autumn park or a winter forest. Framelights are easy to use, as they are equipped with a click profile.

Due to this, the upper part snaps off and the protective module is removed. A variant with a “Magnetic” design is also used. His system uses magnets to secure the canvas.

Using a false window, you can imitate any view from the window that you want

Step-by-step instruction

Designing glass for edge lighting is within the capabilities of any homeowner. About the features of the process in order:

We cut out a light panel of the required size and shape from plexiglass. To do this, we use a hacksaw, jigsaw, etc.
We process the edges and make a recess at the end for the LED components.
We apply the design to self-adhesive paper and glue it to the canvas.
Using a scalpel, cut out the outline.
Using an electric drill, we engrave the glass along the marked line.

: DIY engraving on plexiglass.

Now you need to assemble the circuit. We take the LEDs and solder them to their positive terminals via a resistor. We insulate the contacts with heat shrink. Using acrylic glue, we attach the LEDs to the end holes of the canvas. To check the serviceability of the system, we connect the pluses and minuses along the wires and attach them to the battery holder.

The result is an excellent night lamp, assembled yourself.

You can make a beautiful lamp from plexiglass if you follow the instructions

Materials and tools

Have you decided to make your own edge lighting? Make sure you have everything you need at hand:

acrylic canvas;
aluminum profile;
LED Strip Light;
small 12V power supply.

If the panel is to be placed in a room with high humidity, a special tape is needed. Are you considering a false window as an auxiliary light source? Then you will need an LED strip with increased performance.

Tools usually include a hacksaw, electric jigsaw, drill, fastening components, etc.

To operate the plexiglass lamp you will need a 12V power supply.

Acrylic preparation

It is important to ensure uniform illumination of the panel. We will need high quality acrylic. A balanced, rich glow is guaranteed by diffuse components.

They appear in acrylic sheets during its special preparation. It is impossible to perform such processing at home, so you need to purchase a ready-made canvas that meets all the parameters.

The thickness of the plexiglass is determined taking into account the dimensions of the light panel.

The ends in acrylic fabric must be polished. In the piece where there are no LED components, we apply reflective material. During production, acrylic is covered with a protective film. It prevents damage to the canvas and redistribution of light. Remove the film before installing the structure in the profile.

Profile assembly

Aluminum profile components are at your disposal. We cut them to the required sizes at an angle of 45°. Then we connect the parts using the corners.

Three sides are ready, now we install LED components throughout the entire interior. We connect the wires in advance to ensure contact with the power supply. The 12V adapter is capable of providing energy to a tape up to 5 m long.

We screw at least 4 fasteners to the top of the profile for further installation on the wall.

Aluminum profiles for false windows must be mounted at an angle of 95°

Working with the light panel

Three sides of the profile are assembled and the LED components are secured, we begin the installation of the light panel. We need a reflector - a sheet that reflects light. Let's add it to your profile.

We also add an acrylic sheet, a film with an image, and a protective coating to the design. We install the canvas above the LED components. This promotes good light scattering.

At the end we attach the last side of the profile.

An important nuance: the poster must be printed on backlit film - this way good light transmission is achieved. To make the structure more rigid, a backdrop of sufficient thickness is inserted into it.

Wall mounting

The light panel is ready, now you need to secure it. Hooks are mounted to the wall using dowels. All that remains is to hang the false window and connect the power supply.

Using simple technologies, you will be able to create a modern design in any room on your own. Acrylic edge lighting will create a cozy atmosphere and, if necessary, perform a practical function.

Engraving on plexiglass: description of the process

Laser engraving on plexiglass is the application of an inscription or design and is considered one of the most popular technologies today. The images obtained during engraving are interesting, attractive and unique.

Beautiful engraving on plexiglass

Laser technology allows you to apply inscriptions even on small and very fragile products. Today, new technology is capable of creating vector drawings and raster photographs in any resolution on the surface of plexiglass.

All this has found application in advertising and trade structures, and in the production of souvenirs. Images look interesting if illumination of the engraving on plexiglass takes part in the design.

This decoration element is used in advertising signs.

Engraving technology

Images on plexiglass will look different on artificial glass, it all depends on the technology used to produce the glass.

If plastic glass is made using casting, then the surface of the engraving will be soft, similar to velvet, but on the surface of extruded acrylic the image will be rough and grainy in structure.

By using the depth of engraving and adjusting the angle of the beam, you can achieve quite different and delightful effects in the decoration. For example, inscriptions with shadows appear in images or images with a mirror image are obtained.

All this is successfully used when creating signs with three-dimensional letters or backlit signs.

Laser engraving process

Engraving on plexiglass is always applied from the back side of the acrylic plate product, since it is more convenient to view the entire front side, where the carved image is obtained.

The process begins by removing the protective layer from the side of the surface on which the image is planned to be applied. On the front side, the engraver leaves the protective layer intact so as not to accidentally damage the surface.

Removal of a layer from the workpiece material occurs with a focused laser beam at the highest power.

This process is what causes the planned image to appear; it is based on raster technology, when a laser beam burns not lines, but dots.

The image on the surface is obtained by correct control of all parameters of laser radiation. The quality of the image depends on the properties of the substance in the material on which the design is applied.

On organic glass, engraving should be done with low power, but at high speed. The quality of image application depends on the power. For example, to create notches on the surface, you need to select a small power; if you increase it, the product may be deformed.

Hand engraving of organic glass

Engraving cannot always be done on a machine; if you have a special tool, engraving can be done at home. To engrave with your own hands, you will need an “engraver” machine.

Before you begin the engraving process yourself, watch a video about the operation of the engraving machine. The process itself will be easier if you follow it step by step according to the instructions:

Prepare a sketch; if you do not have the talent of an artist, then look at the pictures in the photo, maybe this will help your imagination.
The prepared drawing will need to be copied onto the surface of the plexiglass. Everything is simple with this: plexiglass is placed on the image and the picture is drawn using a felt-tip pen.
The device is operated using a flexible shaft; it regulates the cutting part of the mechanism.
Engraving is carried out with the cutting part of the nozzle, which can be different, depending on the design.
In order for the process to go well, you need to “rehearse” a little on the remains of plexiglass. This way you can choose the right nozzle for your drawing.
Just like with machine engraving, you don’t need to work at high power, as you can damage the surface of the product.
The whole process boils down to the fact that the nozzle is sunk to the planned depth.
Of course, an experienced master will be able to keep the nozzle at the same level, but a beginner will have to make a limiter using adhesive tape or tape.
During the engraving process, dust will accumulate on the surface; you should not remove it with a rag; you can scratch the surface, so use a vacuum cleaner.

LED lamp made of wood and acrylic

Often, lamps and night lights made of wood are made using epoxy.
For these purposes, jewelry epoxy resin with a transparent texture is used, the cost of which is quite high. If the lamp is made for sale, the profit pays for the venture. But for homemade products, it wouldn’t hurt to reduce the cost a little and, so to speak, practice. Acrylic glass comes to the rescue. It's an inexpensive, unbreakable material that may not be as clear on the edge, but it conducts LED light very well. Working with acrylic is much easier than working with epoxy, and despite the limited capabilities, you can make a beautiful and high-quality product. In order to make an LED lamp from wood and acrylic with your own hands you will need:

Materials:

— cutting boards (the author uses a valuable type of wood); - acrylic glass 8 - 10 mm thick; — a metal inch pipe for making the inner casing; — a metal plate for making the base of the lamp; - wood screws with flat heads; - carpentry or epoxy glue; — quick-drying or natural oil for treating the surface of the lamp; - LED strip and cable. Tools:

— jointing machine;
— grinding machine; - drilling machine and Forstner drill; - sander; - circular; - Miter saw; — a pipe saw or grinder with a cutting wheel; - welding machine; — drill and metal drill with countersink; - chisel; - clamps; - sandpaper; — a paint brush or a piece of foam rubber; - lint-free cloth to remove excess oil; - screwdriver. Manufacturing process Step one: pre-processing of wood
The author uses a valuable type of wood. You can imitate the color of exotic wood using stain. To do this, use an oil-based stain.

The author processed the wood scraps on a jointer and then lightly sanded the surface. For high-quality assembly of the body, make sure that the thickness of the board is the same over the entire area or use lumber that has been pre-processed on a surface planer.

When purchasing bars and boards of valuable wood species, inquire about the degree of processing of the lumber. This wood, to put it mildly, is not cheap, and it would be a pity to mercilessly plan it in order to correct the curvature of the surface.

Step two: making acrylic and wooden elements

You can unravel the workpiece lengthwise using a circular saw, making several cuts on each side. After this, grind the surface of the workpieces on a grinding machine and level it before gluing the parts.

Since wooden blanks have a small area, it is difficult to pass them through the machine. The author glued wooden dies onto a sheet of plywood and in this form ran them through a sanding machine. He used wide double-sided tape to secure it.

Step three: assembling the lamp body

On wooden blanks, draw two lines from corner to corner and mark the center with a dot. Using a drilling machine, drill a hole for installing the LED strip with a diameter of 35 - 40 mm.

Do the same with the acrylic parts. Remove the protective film from their surface and begin assembling the case.

Assemble the body using glue, alternating layers of wood and acrylic, and place the workpiece in a vice for a while.

Step four: making a metal insert

Clean the metal workpieces with a grinder with a grinding attachment and connect them at several points by welding as shown in the photo.

Step five: processing the lamp body

The lamp body must be sanded using a fine abrasive - from 220 to 2000. Remove the chamfers using a sander. The author treated the body with tinting furniture wax. Wax that has not been absorbed into the wood fibers must be immediately removed from the surface of the workpiece. Polish the body by hand or with a sander. This will remove excess coating from the acrylic layers and make the surface perfectly smooth to the touch.

Step six: LED strip installation and final assembly

Become the author of the site, publish your own articles, descriptions of homemade products and pay for the text. Read more here.

Do-it-yourself plexiglass illumination with LEDs - Metals, equipment, instructions

Engineering thought that solves exclusively pragmatic problems sometimes leads to unique results in the aesthetics of our everyday life. One such solution is acrylic edge lighting. Initially, this technology was used to create optical fiber, then in the advertising field, and now it is actively used in home interiors.

New technologies in home interiors

The basis of the edge lighting method is the property of light rays to be refracted, or the effect of total internal reflection. The flow of light, entering the end part of the plexiglass, is scattered and illuminates its front surface. Photos of light panels in the interior of a house clearly demonstrate what acrylic end lighting looks like.

Lighting for home comfort

The use of solutions with this technology allows you to arrange lighting with minimal energy consumption.

And thirdly, often only the edge lighting method allows one to achieve the desired decorative and practical effect.

Illumination of acrylic panels is used in home interiors in the following cases:

for illuminating ceiling panels;
to create a false window with backlight;
for illuminating kitchen apron panels;
for illuminating organic glass shelves;
for illuminating staircase handrails made of acrylic;
for creating framelights as decoration elements.

Framelight is a light panel where you can insert posters with images. Posters can depict a painting in any style, landscape or photograph.

Its beauty is that the printed image can be replaced, and this is quite easy to do.

If such a light panel is placed in a dimly lit area of an apartment or house, then, in addition to its aesthetic value, it also carries a very practical load, creating additional lighting.

If previously photo wallpapers were used for these purposes, now ready-made light boxes - framelights - can be used as an imitation. They are supplied fully equipped, all that remains is to supply a poster with a suitable image.

This can be an imitation of the view from a window with a drawn window profile or a landscape you like. For complete realism, the framelight can be supplemented with an overhead imitation of window sashes.

The ability to replace the poster without much difficulty allows you to change the “outside” picture from time to time. For example, change the view of a summer street to an autumn landscape. This is achieved by the fact that framelights are equipped with a click profile.

It allows you to snap off the top panel of the profile and easily remove the protective module. There is another option: acrylic edge lighting, Magnetic profile.

The peculiarity of this profile is that the upper part is attached to the lower part using a system of magnets.

Materials for self-assembly of the light panel

DIY acrylic edge lighting can be a fun project if you like to DIY at home. To install the light panel you will need:

acrylic canvas;
aluminum profile;
LED line or strip;
compact power supply (adapter) for 12V.

LED strip is a flexible printed circuit board on which LEDs are fixed on one side and an adhesive layer is applied on the other for attachment to an aluminum profile.

If you intend to install an imitation window in a bathroom or other rooms with high humidity, then you should buy a special moisture-resistant tape. If you are using a false window as a light source, you must purchase a heavy-duty LED strip.

You can calculate the power of the adapter using the formula: the power of the block is equal to the power of the LED strip multiplied by its length in meters.

Choose a one-sided profile for the light panel. Pay attention to the following characteristics: profile thickness and lighting system.

Profiles can be designed for fluorescent lighting or for mounting LED strips. Since the thickness of the panel is important for a false window, LED lighting is considered.

For edge lighting, the most important thing is the type and characteristics of the material, so we will consider its choice separately.

Acrylic for edge lighting: description and application

The panel should be illuminated evenly. This requires a certain acrylic for edge lighting, the processing of which was carried out according to all the rules.

A uniform bright glow is provided by colorless diffuse particles that appear in acrylic sheets during special preparation of the sheet.

At home, it is impossible to achieve such a degree of uniformity and intensity of glow, so it is necessary to purchase plexiglass of the required thickness and suitable in other respects. The thickness is selected based on the size of the light panel.

Panel widthLighting on one side	Panel widthIlluminated on two to four sides	Sheet thickness, mm
up to 150 mm	up to 300 mm	4
150—300 mm	300—600 mm	4,6,8,10
300—600 mm	600—1200 mm	4,6,8,10
600—1200 mm	1200—2000 mm	8,10

As can be seen from the table, for a light panel imitating a window, an acrylic sheet with a thickness of at least 8 mm is suitable. You will find on the manufacturers’ websites not only the acrylic itself for edge lighting. The description and application of each type are given in detail, so it will not be difficult for you to navigate the thickness of the sheet and its parameters.

Separately, it should be clarified that the ends that will be illuminated must be well polished. The same sides where the LED strip will not be installed should be covered with reflective tape.

If the acrylic sheet was cut using laser cutting, then additional polishing is not needed. Another important note is that any damage to the acrylic will lead to a redistribution of the light flux, which is why the sheets are covered with a protective film.

It only needs to be removed immediately before installation in the profile.

Assembling the profile and connecting the backlight

Purchased whips (pieces of aluminum profile) are cut to the required sizes at an angle of 45º. After this, they are connected to each other using corners. When the three sides are assembled, you need to install an LED strip around the perimeter of the inner one.

First, wires are connected to the tape with which it will be connected to the power supply. There is an important point here: one 12V power supply is designed for no more than five meters of tape.

If there is more, you need to connect two power supplies. Each tape is connected separately; there is no need to connect them together.

There is another option - take a 24V adapter, then acrylic edge lighting is possible by connecting two LED strips in series.

Light panel installation

After the three sides of the profile have been assembled and the LED strip has been installed, you can proceed to the direct installation of the light panel. To do this, add the following to your profile:

A reflector is a sheet that will reflect light.
Cast acrylic sheet.
Film with a printed image.
Protective sheet.

The installation procedure is clearly visible in the figure. The acrylic sheet must be installed so that it is located above the LED strip, because it is the main light-diffusing element. After installing all the components, the last side of the profile is fixed.

The role of a reflector can be performed by a special reflective sheet. It can be purchased together with light-diffusing acrylic. Companies that sell plexiglass (acrylic) for edge lighting will offer both a reflector and a protective coating. But any reflective fabric can act as a reflector.

For the protective fabric, you can use thin transparent acrylic or dense light-transmitting film. There are certain requirements for the poster. It must be printed on a special film with backlite coating.

To make the structure rigid, you can insert a backdrop into the profile, but you just need to remember to take this into account when purchasing the profile - its thickness should be sufficient for all layers of the panel.

The final stage

When assembling an aluminum profile, it is necessary to screw fasteners (hangers), at least 4 pieces, to its upper part. Once the lightbar is fully assembled, it's time to install it on the wall. To do this, hooks are attached to the wall using dowels. After this, all that remains is to hang the false window and power the power supply.

Thus, using technological innovations, you can independently create an ultra-modern design. Acrylic edge lighting is a bright representative of such technologies; with its help you can create many interesting interior solutions.

Night light safety

On various specialized forums there are examples of design ideas in the field of making decorative light, as in the photo of a night light with your own hand below. In addition, methods for working with various decorative elements and various techniques by which visual original effects are produced are described.

To get inspired, you need to visit such sites, however, first of all, wondering what you can make a night light from at home and how, you should worry about complete safety and build a power supply circuit designed for the light source.

There is a myth that the minimum voltage and minimum power of small light sources are the key to complete safety.

The power supply will operate for a long period of time during an overload, while the special protective circuit breaker will not react

When equipping night lights, as well as power supplies, on your own, it is important to provide the wiring with a protective system.

Features of false windows

The design is delivered ready-made; the user needs to insert a poster with an image. Often, an imitation of the view from a window, different landscapes, or photos are used as a picture.

The poster can be easily replaced at any time. A summer street can easily be replaced by an autumn park or a winter forest. Framelights are easy to use, as they are equipped with a click profile. Due to this, the upper part snaps off and the protective module is removed. A variant with a “Magnetic” design is also used. His system uses magnets to secure the canvas.

Using a false window, you can imitate any view from the window that you want

Necessary materials

LED matrix
To create a night light, you need to purchase LEDs or a matrix of diodes. The quantity is selected depending on personal preference. It is better to buy bright multi-colored LEDs. The current strength of each component should not exceed 20 mA.

You will also need to buy resistors. To create a circuit with a series connection, you need 1 current-limiting resistor. If the circuit is in series, all diodes must be of the same value. When wiring a parallel connection, each LED is assigned its own resistor.

You will also need a semiconductor diode and a plug to connect to the network. The case can be an old disk, a bottle, or other objects made of different materials. You can assemble the case yourself.

The tools required are a plastic plate, screwdrivers, a knife, heat-shrinkable tubing, a soldering iron, and pliers.

How to make an original lamp yourself?

If you have decided on the idea of making it, then it’s time to get to work. The product requires a container made of organic glass. Tools you will need: circular saw, scissors, pencil. Stock up on copy paper, stencils, and paint. You also need a cartridge and a wire with a switch.

Expert opinion

Ivan Zaitsev

Lighting specialist, consultant in the building materials department of a large chain of stores

You can buy a stencil, or you can make it yourself. There are quite a lot of different options on the Internet, you should choose the one you like and print it out. You need to copy the stencil onto vinyl paper using carbon paper. Cut out the stencil according to the applied pattern, remove the protective film and glue it to the plexiglass. Gluing requires care; the surface must be clean and dry.

The next stage in the work is painting the plexiglass. It is better to apply the paint from a sprayer: layer by layer. The number of layers is determined visually, depending on the quality of application. It is better to choose paint to match the home interior.

The paint should dry well, a day is enough. Remove the stencil carefully, without scratching the painted surface. You can use plexiglass as a material for the lamp, which can be either transparent or in different colors. Then there will be no need for painting at home.

All that remains is to connect the socket and wire with the switch, check how the lamp works.

A table lamp or floor lamp, in addition to decorating with a stencil, can also be decorated with photographs. Beautiful landscapes and city streets will create a unique look for the product. And children's photographs, family vacations and celebrations will remind you of happy moments. This plexiglass lamp will not leave anyone indifferent. How nice it is to receive it as a gift! Photos of friends, parents, grandchildren with grandparents - whatever your imagination desires!

Necessary materials

You will also need a semiconductor diode and a plug to connect to the network. The case can be an old disk, a bottle, or other objects made of different materials. You can assemble the case yourself.

The tools required are a plastic plate, screwdrivers, a knife, heat-shrinkable tubing, a soldering iron, and pliers.

Why do you need backlighting?

Edge lighting can provide a pleasant atmosphere in the home

Canvas lighting is used in tandem with the following designs:

ceiling panels;
false windows or framelights;
kitchen apron panels;
shelves;
handrails of stairs, etc.

In fact, you can turn any idea into reality.

Assembly algorithm

LED night light – fan

First of all, you need to solder a circuit of LEDs, resistors and other components. After soldering, the contact points must be insulated using heat shrink.

Next, the body of the future lamp is assembled. There should be a diagram inside. The body can be made from any available materials. For example, transparent plastic elements from CD boxes are suitable. They are glued together with strong glue, and a disk is placed on the bottom so that the light is reflected from it. The entire structure must be degreased with alcohol. If desired, you can glue the legs to the assembled lamp.

A lamp on a fan is perfect for the bedroom. You need to buy a large fan and attach a soldered circuit to it.

Night light starry sky"

This night light imitates the night sky with constellations. To make it you will need a glass jar with a lid, foil, an awl, scissors, an LED flashlight and a tray.

On the foil you need to draw a sky with stars in any order that the master wants. Place the sheet on a flat surface and use an awl to make holes for the stars. The foil is cut to fit the height of the jar. The paper is rolled into a tube and placed in a jar. A flashlight is placed at the bottom of the can. When you turn it on, you can see the glow from the night light on the walls and ceiling.

In the same way, you can make a night light with your own hands from LEDs and a tin can. It needs to be painted, all stickers removed and holes made. A candle, lantern or garland is placed inside.

Night light in the shape of the Moon

You will need an LED strip and 2 transistors. They will regulate the device and turn the board on/off.

To make a night light from plywood with moon-shaped LEDs, you will need a sheet of plywood that is cut into a circle. You need to glue a printed image of the Moon on top. Then you need to drill 2 holes for fastening and pulling wires. The base of the lamp is glued to the plywood. After drying, the LED strip is glued around the perimeter.

4 5

Night light from an electric plug or fumigator

Night light made from LED strip and power supply

You will need LEDs, 2 resistors, 2 capacitors, a zener diode, and a heat shrink tube.

The grounding pins are removed from the plug. You also need to remove the clamp and grind off the rim on the LED using a file.

A night light is made from fumigator in a similar way. It must be disassembled, the heating element removed and the LED placed in the free space. The voltage passes through the capacitor. A rectifier bridge is installed at the output, which smoothes out ripples and equalizes the voltage.

You can put a lampshade on the fork, which you can make yourself or purchase in a store.

Little tricks in making

Favorite photos need to be printed on a printer using special paper. The paper should not be very thick, as it must transmit enough light.
Cut out the resulting photographs and record them on transparent film.
Attach a cut-out sheet of organic glass to the frame of the lamp, fix the film with the photo on it, then put more plexiglass on top.
Fasten all the elements with screws, cut off the protruding edges of the film.

In addition to floor and table lamps, you can also make a ceiling chandelier with your own hands. Additionally, you just need to provide special fastenings. Decorative thread is suitable for decoration, preferably linen. Choose the appropriate color to match the lamp or interior. It will look original in weaving.

Plexiglas for making lamps can be purchased at building materials stores. It is convenient to process at home. The material is easily cut with a circular saw. It is better to cut at medium speed to avoid melting due to overheating. You can drill it with ordinary drills. It is recommended to place plywood under the glass when drilling to prevent cracking.

If you don’t have the necessary tools at home, you can cut them in the store into the desired shape and size.

The light source is ready with your own hands. All that remains is to admire the results of the work. An original decorative product will not leave anyone indifferent.

Lamp from a can

Using available materials, it is quite possible to build a large homemade lamp that can decorate not only a nursery or bedroom, but the entire room. To create such a miracle, you will need an original tin or plastic tea can. You also need scrapbooking paper, stationery cardboard, a paper knife, acrylic paints, glue, sandpaper, and masking tape. And since in this case we are making not just a night light, but a lamp, we need to prepare a light bulb socket, an incandescent light bulb itself, a power cord and a switch.

Cut out a sheet of scrap paper that can be used to completely wrap the jar.

Please note that the bottom of the tea bag will be the top of the lamp. Remove the lid from the jar, lean it against a piece of paper, trace it with a pencil and cut it out. Connect the cut out template to the wrapped jar using masking tape. Trace a circle with a pencil. Cut out a window according to your markings

Sand the edges with sandpaper. Re-trace the oval template onto the cardstock. Draw stripes inside it and cut out some of them. Glue the cardboard to the jar on the inside. You can decorate the outside of the jar as you wish, using paper, cardboard, acrylic threads, lace, etc. At the back of the lamp, cut a circle for the power cord. You need to make a hole in the lid for the cartridge. Assemble a socket with a light bulb, a switch and an electrical plug into a circuit. Place the socket in the jar, screw in the light bulb. Assemble the lamp and check its operation by plugging it into an outlet.

Plexiglas backlight

Plexiglas edge lighting is not only a beautiful, but also a practical solution for apartments and industrial premises. A cozy and warm atmosphere in the room is achieved thanks to the light that is refracted through the canvas and spreads in uniform streams. In addition to its decorative function, a bright pattern mounted on the wall creates high-quality and uniform lighting of the space.

Cozy light in every home

Plexiglas is a unique material that distributes and refracts light. This property is used when creating luminous plexiglass with your own hands.

An interesting and beautiful idea is based on the placement of an LED lamp at the end of the plexiglass. The rays reflected from the edges spread across the surface of the canvas and create interesting effects.

For example, engraving on the surface of glass will form a line that repeats the image.

Illumination of plexiglass with LEDs is a convenient and beautiful interior solution using modern technologies. The diffused stream of light is pleasing to the eyes. In addition, this is a very practical and economical lighting option, since plexiglass lighting has minimal energy consumption. And this method is sometimes the only way to achieve the desired effect.

In the interior, do-it-yourself plexiglass edge lighting is used because of the unusual appearance of such decor, which creates a stream of diffused light. Aesthetics here combines very well with functionality. The picture, glowing from within, looks very impressive. The rays hitting the plexiglass are refracted in the engraving lines and reproduce the contours of the design with a soft glow.

Plexiglas is a type of plexiglass for LED lighting of lightboxes and advertising panels. Colorless particles in its composition scatter the rays going to the end part of the sheet. At maximum power, uniform illumination of the surface is created without distortion or darkening.

Manufacturers of plexiglass also produce acrylic sheets that are capable of excellent scattering of light rays directed from the ends of the canvas. Uniform dispersion over the surface of the sheet is ensured thanks to special reflective microparticles. As a result, they function as multiple light sources.

Places of application

LEDs illuminate structures for various purposes, for example:

shelves,
ceiling panels,
false windows,
stair railings,
kitchen aprons, etc.

In cinema halls and apartments it is convenient to use framelight - a light panel where you can insert posters with any images that can be very easily replaced. A winter forest instantly turns into a summer street or easily gives way to an autumn park. Framelights are very convenient to use because they are equipped with a click profile.

To achieve good light transmission, the poster must be printed on backlit film. One thick backing that is inserted into it will help make the structure more rigid.

Items needed to make an edge light

First you need to develop a sketch of the picture and prepare tools and materials. You will need:

plexiglass,
wooden blocks for wall mounting, nails, bolts and nuts,
LEDs, compartment for three miniature batteries, resistors, electrical wires and heat shrink tubing,
glue, paint, self-adhesive paper,
pencil, ruler, sharp knife,
soldering iron, drill and wire cutters.

The video explains how to make plexiglass backlit with ledexlight LEDs:

Works with plexiglass

The shape of the lamp is cut out of the canvas, and the edges are well processed. Holes for LEDs for end illumination of plexiglass are made in one of the edges.

A pattern that will be illuminated is applied to self-adhesive paper and glued to the plexiglass. A strip of the future contour is cut out with a sharp knife.

A drill is used to engrave plexiglass along the contour with a groove of the required depth, which regulates the brightness of the pattern.

Assembling the circuit begins with soldering the LEDs to the positive ends along a resistor, and to the terminals - two-core wires, which must be insulated with heat shrink.

The LEDs need to be glued into pre-prepared end holes, the plexiglass with fasteners must be assembled into a single structure and the wires must be pulled through. The correct operation of the circuit and connections must be checked. All the positive ends are connected into one, and the negative ends into another core.

Observe the correct polarity and connect them to the battery holder. If the connection is functioning, you can solder and insulate the wires and decorate the fasteners and panels.

Is it possible to make an LED chandelier with your own hands?

LED strips and panels of varying brightness and colors are available for sale. Using them, you can assemble homemade lamps. But you will need knowledge of basic electrical engineering and some construction skills (soldering and others, depending on the materials chosen).

The shape of a LED strip chandelier can be:

square or rectangular;
round;
more complex - for example, in the form of a structure made of slats, pipes, etc.

For the latter case, a flexible LED strip, which is glued to the base, is more suitable. The sticky layer is already applied on the back side; you just need to remove the protective film and press the strip to a clean surface.

For round devices, it is convenient to take a ready-made panel of the same shape. LEDs are attached to the base; often each has a miniature lens that magnifies the outgoing rays.

For a rectangular case, a ready-made module is also used. You can take the tape, cut it to size and place it in several rows or in a more complex pattern. A translucent plate that scatters light (made of frosted plexiglass or other similar material) is placed on top. Then the flow becomes uniform.

And for square models, you can take an LED module from an Armstrong cassette ceiling.

DIY acrylic edge lighting

How to make false windows using ready-made framelight profiles

Let's consider one of the options for an interior solution: acrylic end lighting when creating a false window.
Sometimes in rooms without windows or where there are not enough of them, designers practice creating false windows. If previously photo wallpapers were used for these purposes, now ready-made light boxes - framelights - can be used as an imitation. They are supplied fully equipped, all that remains is to supply a poster with a suitable image.

The ability to replace the poster without much difficulty allows you to change the “outside” picture from time to time. For example, change the view of a summer street to an autumn landscape. This is achieved by the fact that framelights are equipped with a click profile.

It allows you to snap off the top panel of the profile and easily remove the protective module. There is another option: acrylic edge lighting, Magnetic profile.

The peculiarity of this profile is that the upper part is attached to the lower part using a system of magnets.

LiveInternetLiveInternet

Quote from Rudenka's message

Read in full To your quotation book or community! Acrylic Beautiful Lamps. MasterClassAfter the New Year holidays, winter compositions can be replaced with spring, floral ones.

For lamps we use acrylic glass (a more common name is plexiglass, or plexiglass), which is sold in hardware stores or in advertising supply stores. Today, this is one of the most sought-after materials among designers all over the world. Due to its strength and light transmission, it is excellent for making aquariums, vases, shades and lamps. From a sheet measuring 1.2 m x 2.4 m and 1.5 mm thick, you can make two large lamps or three (or even four) small ones. We will also need double-sided mounting tape for gluing the acrylic - but instead, you can use a drill: drill holes and lace the acrylic frame of the lamp with rope. For the base on which the lamp will be mounted, it is necessary to cut two circles from a 3 mm thick MDF sheet: we cut one to the diameter of the lamp, the other should be 4–5 cm larger. We glue the smaller circle to the larger one using a glue gun - we get the base of the lamp, which must be painted over with white acrylic paint. Then you can place snowflakes, beads, balls on it...

Next you need to cut out the acrylic sheet. To do this, measure the diameter of the base, add 4 cm to it and transfer the resulting value to a sheet - this is one side of the rectangle. The second side will be equal to the height of the lamp. Using a sharp knife, use a ruler to cut out a rectangle from which we will roll up the frame of the lamp. Cutting a sheet of acrylic and gluing it with double-sided mounting tape is not an easy task for a woman’s hands, so I asked my artist friend to do it. Mounting tape provides a hidden, almost invisible connection, but this tape is not always of high quality. Some of our lamps were firmly attached, and some were unstuck. Then we came up with another method of fastening: we drilled holes (two rows in each edge), twisted the sheet and aligned the holes. This work is best done with an assistant.

All that remains is to lace the frame from top to bottom and secure the lacing at the end with a strong knot.

Pay attention to the small detail: a corner for the cord is cut out at the bottom with scissors

All that remains is to figure out how to fill the lamp, then place the finished composition inside the frame, put it on the base and secure it in several places with a hot glue gun. We prepared snow branches to fill the lamp, some decorated it with old toys...

...someone with New Year's beads and balls.

We bought cellophane and placed it in a lamp together with a garland - it created the impression of ice.

You can fantasize about different (New Year!) themes.

When you're done, you may have some small pieces of acrylic left over that can be used to make interesting wall clocks. Two identical squares are fastened with a clock mechanism, and on the inside of each there is an improvisation on any theme from wallpaper, paper, napkins...

source

Rudenka

Profile for lighting

An aluminum profile performs two important functions:

For such profiles, shelves made of glass with a thickness of about 1 cm are suitable. If you use a shelf with a smaller thickness, then it is necessary to use a special gasket that will compensate for the difference in thickness and firmly hold the glass in the profile.

Interesting. Glass edge lighting can also be used for glass stairs. It will provide comfort by illuminating the road in the dark and create a beautiful soft glow.

The LED strip installed in the profile will not distribute light along the edges, it will be directed exclusively to the end of the glass, this will provide additional savings, since the light will not be wasted.

LED night light

To make an unusual and beautiful LED night light that can be placed in a nursery, you need to prepare a pair of transparent plastic tubes with unequal diameters. You will also need LEDs with the desired brightness and color range. Also prepare glass pebbles, wire, a larger cork, superglue, pliers and a board for the LEDs.

Bend the ends of the LEDs with pliers.
Connect all LED bulbs with a piece of wire in a parallel circuit, observing polarity.
Connect the ends of the wire to the board.
Check the working part of the night light, if the LEDs get very hot, add a resistor to the circuit.
Glue the tubes one into the other. Place decorative balls into the void.
Place the LED plug onto the tube. If the diameter of the plug is larger than the tube, make a seal from a leather belt.
The LED night light is ready, you can turn it on.

Advantages of an LED night light

A decorative LED lamp Moon
Night light from LEDs is quite simple to make. The scheme does not cause difficulties even for inexperienced people. The advantages of an LED light source include:

low power consumption;
long service life;
availability;
variety of application schemes;
quality of light;
good lighting;
no heating;
safety.

A homemade night light made from LEDs can be used for illumination, allowing you to navigate in the dark. The device can be installed in any convenient place.

Making a hole in the bottom of the base for the controller

The controller will be placed at the bottom of the base. It's quite large, but I didn't have a smaller one, which means I need to find a way to fit it into the bottom of the tree. I only use hot glue to secure it. To make a square window for the controller, I drilled a hole 12 mm in diameter, and then inserted a jigsaw into the hole. I cut out the window and trimmed it with a file. Another thing I need to do is drill 2 holes on the back bottom. These will be the holes for the adapter and the infrared receiver. Since I have a controller with a remote control.

Cutting wood and acrylic glass to size

For this project I decided to use solid wood. I had a small piece, 20mm thick, in my workshop that is perfect for this purpose. The acrylic I used was 5mm thick and I think it's a perfect combination with the wood. The base of the lamp is 16 by 9 cm. The upper figure, placed vertically on the acrylic base, measures 28 by 14 cm. My experience when cutting acrylic has shown me that when the cross slide moves slowly, the acrylic melts, so you need to move faster to get clean cuts .