Scheme of a strobe light on LEDs: a diagram of how to make an LED beacon with your own hands

The device, which reproduces a continuous light flux in a pulsed lightning-like mode, is used in various fields - from ignition system indication to lighting of discos and signaling devices of special vehicles.

Let's consider how to make a strobe light using LEDs with your own hands, what its circuit and printed circuit board look like, what necessary tools and components are needed for this, what stages the electronics assembly consists of, as well as what other additional procedures will be needed to bring the device into working condition.

Required Tools

To make a strobe light based on LEDs with your own hands, you will need the following set of tools and accessories:

1. Measuring device.
2. Screwdriver Set.
3. Pliers.
4. Soldering station or soldering iron with necessary components.
5. Drill or screwdriver.
6. Wood knife.
7. Felt pen.
8. Sandpaper.

Important! When introducing very powerful LEDs into a strobe circuit, the resulting flashes of light can adversely affect vision. Therefore, during operation of the device, it is necessary to exclude direct visual contact with such a light source, for example, by installing a matte diffuser.

Electrical circuit of the strobe

A distinctive feature of the presented strobe light circuit is its simplest configuration and the ability to control the ignition timing in a car engine up to 5000 rpm.

Structurally, the diagram consists of several functional units. A voltage converter, a pulsed light lamp, an ignition unit and an inductive spark sensor.

Schematic and PCB

You can make a strobe using LEDs using several schemes. One of the simplest and most accessible is the following:

This circuit is based on a timer such as the LM555 timer, or its foreign analog NE555. It produces pulses, the parameters of which are determined by a potentiometer or resistor. A special feature of this model is that the board can include 3, 10, or any other number of diodes. The main advantage of this scheme is the stability of the pulses and their independence from the battery potential.

Homemade strobe light for installing the ignition: crazy hands

Many modern car enthusiasts are faced with the need to adjust the ignition angle (IA). Sometimes this procedure can cause certain difficulties for the motorist, which is why many devices have recently appeared on the market to perform this task. For example, you can use a strobe light to carry out the ignition installation procedure yourself, which we will discuss below.

So, you have decided to make ignition settings on your car, but you have no idea how to set and adjust the OZ. To ensure that the set angle does not cause discomfort to the driver while driving, you can use a strobe light for ignition.

Schematic diagram

Schematic diagram for the development of a strobe light

Below is a diagram of a strobe. If you don’t know how to make a strobe light using LEDs yourself, you can use this diagram. In the end, you will get the simplest strobe, but the device you make will allow you to fully adjust all the necessary parameters.

In the device diagram, it is necessary to highlight several main parts:

1. The power circuit, which consists of components - SA1, which is a switch, diode VD1, and capacitor C2. A DIY circuit must include a diode designed to protect other components from erroneous polarity reversal. The capacitor performs the function of blocking impulse noise, helping to prevent failures in the operation of the trigger. As for the switch, it can be replaced with a toggle switch, the main thing is that the component can turn the power on and off.
2. A homemade strobe for ultrasonic installation must include an input circuit consisting of a controller, resistors R1, R2, and capacitor C1. The controller option in this case is provided by an alligator clip, which is fixed on the high-voltage cable of the first cylinder. As for components C1, R1 and R2, they form a simple differentiating chain.
3. Another important component of the strobe used is the trigger board, which is assembled using two monovibrators designed to generate a signal of a given frequency at the output. Capacitors and resistors in this case are frequency-setting components.
4. Another component is the output stage, which is assembled using resistors R5-R9 and transistors VT1-VT3. The transistors themselves are designed to amplify the output current of the trigger. Resistor R5 allows you to set the base current of the first transistor. And thanks to resistor R9, the likelihood of malfunctions in VT3 is eliminated.

Required Components

For the LED strobe circuit discussed above, you will need the following main components with the corresponding characteristics:

Average price of a factory product and its disadvantages

The factory version of the device has some disadvantages that significantly reduce the usefulness of such an acquisition.

It is always more convenient to set the ignition on carburetors with a strobe light

Firstly, the cost of factory stroboscopes is quite considerable. So the digital model Multitronics C2 will cost the buyer about 900-1000 rubles. The more functional AstroL5 strobe will cost 1,300 rubles. Focus F1 - a model suitable for servicing both gasoline and diesel engines - will require 1,700 rubles, its more “advanced” brother Focus F10 - 5,600 rubles.

Secondly, manufacturers often use an expensive gas-discharge lamp in the design of their products. It has a limited resource and may require replacement after a short time, which will not only hurt your pocket, but will be tantamount to buying a new strobe light.

Electronics assembly

The assembly of the strobe circuit is carried out exactly in accordance with the circuit discussed above. Ice elements are soldered according to the principle - a cathode to an adjacent anode, etc. The extreme contacts are soldered to the conductors with a connector. The switch is connected to the battery holder. This will allow the lamps of the device to work even if it is turned off - with the DC adapter plugged into the connector, as shown in the figure.

When choosing high-power LEDs, the inevitable result of their operation will be the production of heat. The metal case can serve in this case as a radiator.

On tl494

The control board can be built on the common TL494 chip. It is a PWM controller, but it can be used as a pulse generator with different duty cycles and frequencies. Parameters are controlled using external elements.

Stroboscope control board based on TL494 chip.

By selecting the value of R4, the blinking frequency is set; by selecting R3, you can adjust the duration of the flashes. Instead, you can mount multi-turn trimmers and adjust their blinking parameters. As a key, you can use both field-effect and bipolar transistors for the corresponding drain (collector) current.

Important! In this and subsequent circuits, you need to pay attention to the presence of current limitation through the LED strobe light - driver or ballast resistor. If there is no current-limiting device or circuit, a resistor with the appropriate resistance and power must be connected in series with the flashlight.

Preparing the body

When the LEDs, transistor and other electronic components are assembled into one circuit, it is necessary to prepare the body of the future strobe. First of all, you need to make mounting holes and connectors:

1. To secure the diffuser, board and housing, three-millimeter holes are made for installing holders and tightening screws.
2. 10 mm holders are installed between the LED board and the plastic plate, and 22 mm holders are installed to fasten all the parts.

DIY strobe light for disco

Surely many of us would like to have a strobe light at home to decorate a small party and give it a little drive. As a rule, they are made using flash lamps, but unfortunately they are quite expensive and have a short resource.

I decided to replace the lamps with LEDs, and I can say with confidence that even a novice radio amateur can make such a strobe light for a disco with his own hands.

The strobe itself is assembled on 2 printed circuit boards, one of them contains LEDs, and the second contains a control unit. The main part in the control unit is the LM555 timer chip.

It is this that generates pulses, the frequency of which determines how quickly the strobe will flicker, and is regulated by a variable resistor. I used 60 LEDs, but you can use any number that is a multiple of three (3, 6, 9...).

Any source from 6 to 12 volts is suitable as a power supply. For me it runs on one Krona battery, but if you wish, you can connect it to a 12 Volt power supply (an additional connector is provided for this). In this case, the strobe light shines much brighter.

Here is a list of radio components that will be needed when making a strobe light:

• Ultra-bright LEDs (white, 5 mm) - 60 pcs;
• Timer chip 555;
• Field van IRFZ44N;
• Variable resistor 1 mOhm;
• Resistor 5.6 Ohm (2 W);
• Resistor 56 Ohm;
• Resistor 10 kOhm;
• Resistor 100 kOhm;
• Capacitor 1uF x 50V;
• Capacitor 1000uF x 16V;
• Diode 1N4148;

Body parts and other small things:

• Plastic case 90×60×25 mm;
• Plexiglas 90×60 mm;
• Textolite;
• Racks M4×22 mm (female-female) - 4 pcs;
• Stands M4×10 mm (female-male) - 4 pcs;
• Screws for racks M3×8 mm;
• Krona battery + mating connector for it;
• Power connector (male);
• Slide switch (2 positions);

The circuit and PCB were drawn in Eagle software. The control board turned out to be small; if desired, it can be made even smaller using SMD components. The dimensions of the board with LEDs are 87 by 57 mm.

Schematic diagram of the LED board (PDF, 62 KB); Printed circuit board for LEDs (PDF, 13 KB); Schematic diagram of the control board (PDF, 48 KB); Control printed circuit board (PDF, 10 Kb); Arrangement of elements (PDF, 47 KB).

Unfortunately, I did not take photos during the soldering process, but I hope that this will not be a hindrance to you. Here are some photos showing the already soldered strobe boards.

After manufacturing printed circuit boards and soldering radioelements onto them, you can begin packaging.

Inside the case we had to cut off several plastic stands that were in the way.

To protect the LEDs, I used plexiglass, installing it on stands (10 mm between the plexiglass and the strobe body).

Now all that remains is to insert all the connectors, tighten the bolts and your DIY strobe light for the disco is ready!

Here is a video of the strobe in action:

Completion of work

When the entire LED strobe circuit is assembled, it can be connected to power and tested for functionality. The considered example allows the use of various power sources:

1. Power supply from 6 to 12 volts - creates different levels of luminescence and brightness depending on the required task in different rooms.
2. 9 volt battery. It fits directly inside the housing and makes it possible to use the strobe in autonomous mode outdoors.

When using high-quality branded components, the strobe will work for a long time and will not require repairs in the coming decades.

Recommendation! In order for the strobe to emit different colors, instead of conventional LEDs, you need to introduce RGB elements with a controller into the circuit. Alternatively, you can stick a colored film onto the diffuser.

DIY strobe light based on LEDs (diagram)

Today, LEDs are the most common type of lighting fixture. They achieved such popularity for a number of advantages that other lighting devices cannot compete with. The first advantage was cost-effectiveness. This positive property was achieved due to lower power consumption, while their brightness is at a very good level. In addition, the operating time of the average LED reaches 50,000 hours of continuous operation, which in turn has become another advantage of using this type of lighting in all areas of human activity.

The use of LEDs for the manufacture of strobe lights has not been spared. The availability of this part allows them to be used on a large scale, and the low power consumption has contributed to the fact that a brighter and more noticeable strobe can be made. This device can be easily used in the brightest daylight.

The circuit of this device uses a special 155AG1 microcircuit, triggered by pulses with negative polarity. In the circuit itself, 3 resistors were used, which influence and “cut” the amplitude of the input signal. And the further duration of the pulse signal is set using capacitive capacitor C4, as well as resistor R6. The power source for such a circuit must be connected to the vehicle’s on-board electrical network.

Main conclusions

To make your own strobe light based on single-color or RGB LEDs, you need the following tools and components:

1. Ruler, screwdrivers, pliers, sandpaper.
2. Drill or screwdriver, screws, holders.
3. Soldering iron with a set of accessories.
4. Housing, LEDs, electronic components, wires, plexiglass.

The assembled strobe circuit using simple LEDs can be powered by a nine-volt battery placed in its body, and from a mains power supply with a rating of 6 to 12 volts, producing different brightness of the light flux.

If you know another, simple or complex LED strobe circuit for a specific application, be sure to share this information in the comments.

Construction and details

The entire strobe circuit is assembled in a two-half plastic case measuring 4.5 × 7.5 × 16 cm. To allow light to escape from the flash lamp, a round hole is made in the end wall into which a lens in a mandrel is inserted.

This is not necessary; the window can be closed to protect it from dirt getting inside the strobe using any transparent material, such as organic glass. The lamp, to reduce light loss, is half wrapped in staniol foil.

All parts of the strobe, except for the lamp, are assembled on the printed circuit board shown in the photo.

Pulse transformer T1 has two windings. The primary winding is tapped from the middle. When winding, you need to measure the required length of wire with a diameter of 0.3-0.5 mm, fold it in half and wind 24 turns. Then connect the beginning of one winding to the end of the other, this will be the middle point. The secondary winding is wound with a wire with a diameter of 0.15-0.25 mm in the amount of 638 turns. To make a transformer, a ferrite core with a coil can be used from a step-down transformer of a non-repairable switching power supply AT or ATX computer, after first removing all the windings.

The T2 ignition pulse transformer is wound on a ferrite ring with a diameter of 15-20 mm with a permeability from 1000 to 3000 Nm. The primary winding is wound with 0.3 mm wire and has 4 turns. The secondary winding is wound with a wire with a diameter of 0.1 mm in silk insulation and a number of turns of 500. The large number of turns of the secondary winding was not taken by chance; at high engine speeds, capacitor C6 does not have time to fully charge and the ignition voltage decreases. Thanks to the reserve, sufficient voltage is provided for ignition. Before winding, the ferrite ring must be covered with insulating tape to prevent damage to the wire insulation. Before covering with insulation, it is necessary to grind off the sharp edges around the circumference of the ring with fine sandpaper. After winding, to avoid interturn breakdown of the insulation at high humidity, the transformer windings are impregnated with wax.

The inductive sensor coil is wound on a ferrite ring with a diameter of 40 mm with a permeability of 1000 to 3000 Nm. 35 turns of wire with a diameter of 0.8 mm are wound onto the ring evenly around the entire circumference. The top of the winding is covered with a layer of insulating tape.

The diameter of the ferrite ring was chosen based on the possibility of threading a high-voltage wire through the coil going to the car spark plug. But the practice of using a strobe has shown that it begins to work stably if you simply attach the coil to a high-voltage wire.

The strobe is connected to the battery using two alligator clips. For error-free connection, the crocodiles are marked with polarity.

Capacitors C5 and C6 type K73-17. The EL1 flash lamp type ISSH-15 is a low-power strobotron, its service life is more than 300 hours. It is specially designed for strobe lights.

Unlike the IFK-120, the ISSh-15 lamp has a longer life and can operate at higher frequencies. In the absence of ISSH-15, you can use IFK-120.

For ease of operation when setting the ignition timing in a car, a two-range analog tachometer with an extended scale is built into the strobe.

Stroboscopes for discos - purpose and features of 2022 models

Lighting equipment, in connection with the growth of scientific and technological progress, is actively developing, surprising consumers with new products and original solutions. One of the most non-standard types of modern lamps are stroboscopes, which are widely used today. They have a number of unique features and advantages compared to other lighting equipment.

What is a strobe in simple terms?

This is a special lighting device that creates a luminous repeating effect from emitted streams of light. Step by step, it looks like this: in an instant the object is illuminated by a flash of light (a feeling is formed that the figures are moving unevenly) and in the next fraction of a second the light flash illuminates the space from a different angle (a feeling of uneven movement is also formed), due to which a unique lighting effect is provided.

Currently, many models of devices are produced, which, according to their design features, are divided into the following groups:

• Electro-optical stroboscopes for discotheques - to interrupt the flow of light, light shutters are used in the design of the devices. The functioning of the technology is based on various optical-electronic effects.
• Optical-mechanical stroboscopes for discos - discs with slots act as a light interrupter.
• Electronic stroboscopes for discotheques - the design of the devices includes a special electronic circuit or pulse generator that regulates the frequency of pulses in light sources, which are LED or gas-discharge lamps.

Stroboscopes of different configurations differ in the power of the lamps used. The frequency of outbreaks also varies. Depending on the purposes pursued, the devices can be installed indoors or used in open areas. The brightness of the flash depends on the installed reflector, the shade of the cap and the type of lamp.

Currently, lamp strobes for discotheques are one of the most effective ways to transform the dance floor. They are guaranteed to last much longer and make the indoor atmosphere more environmentally friendly. Other advantages of lamp stroboscopes include ease of design and installation, as well as resistance to vibration, which is especially important for star concerts, where powerful sound is always used.

An additional advantage of the devices is ease of installation, so the equipment can be used to organize shows in any place, making the holiday bright and exciting for all participants.

The use of strobes for discos

The main use of strobe lights for discotheques is to create unique entertainment events. Devices for light repeating flashes are widely used in nightclubs, cafes, restaurants, bars and pubs, on the stages of concert halls, theaters and cultural centers. Many private and home parties today are held using such equipment, which provide the necessary lighting effect inside objects or in open space, transforming the surrounding atmosphere.

For those who are concerned about safety, we can assure you that the equipment does not overheat, since modern equipment has been tested over years of operation and meets all necessary safety standards. Strobes instantly respond to sound, projecting bright flashes of light in time with the music playing. When using the devices, event participants will be surrounded by the unity of light and music, which is extremely important for creating the effect of proportionality and balance indoors or outdoors.

Stroboscopes for discos from a specialized company

The technique is indispensable for anyone who plans to organize a full-fledged dance event, show, party, concert or even theatrical performance.

Our specialized store offers a wide range of popular stroboscope models.

Lamp stroboscopes for discos - devices for 35W and 1500W, respectively, for 50 sq.m.
and up to 500 sq.m., depending on the tasks that the client sets for us. In the first case, strobe lights for home discos and small cafes at 35W, which are ideal for rooms up to 50 sq.m. The flashes are bright and clear, the lamps are rated for 50,000 hours, are portable and lightweight, easily attach to walls and do not require special mounting. RGB strobes are devices that combine rgbw leds light emitting diodes and are often combined with other color music capabilities.
We have all the presented models in stock today. For owners of clubs, cafes, restaurants, bars, dance floors and other establishments, we have prepared just such equipment that can provide the necessary background effect. Bright flashes of light will explode the space with powerful energy that will spread to everyone present.

For those who plan to organize a party at home, there are models of strobe lights for private use that have the same functionality as professional models:

• dynamic flickering effect;
• flash frequency control;
• absence of any possibility of overheating;

Home models are more portable, which is extremely important when space is limited.

In addition to organizing entertainment events, many business representatives prefer stroboscopes in the process of developing commercial activities. This is an excellent solution for attracting new customers without significant effort. In our online store you can choose the optimal model based on planned events, projects and subsequent operating conditions. Our consultants will help you choose a model with suitable characteristics.

Strobe lights for discotheques - 2022 models

To organize a party, New Year's disco or other celebration at home, you can use the STROBELIGHT PRO model. This is a portable device that allows you to instantly produce bright flashes of light. The power of the lamp strobe is enough to cover 50 square meters. m of facility area. The portability of the device allows you to take it with you for outdoor parties and other entertainment events.

To achieve a more effective effect, you can use the STROBELIGHT PRO stereo kit, consisting of two stroboscopes.

For nightclubs and larger spaces where large entertainment events are held, the best option is a powerful 1500 W strobe with a built-in ready-made lamp and two replacement lamps.

The strobe speed of 25 flashes per second in the device is adjusted manually or automatically. Technical characteristics allow you to use the device in open spaces, during street discos, organizing outdoor events or in the forest.

A separate category of stroboscopic devices is color music strobe .

These are universal devices that are used both at home and in professional entertainment venues. Color music RUBIN X-700 creates portable light, which is realized in the form of hundreds of bright rays. Using the device, it is easy to decorate any room, providing guests with emotions and vivid impressions of the party.

Color music strobe RUBIN MAX is a more powerful model, capable of producing effects in rooms up to 100 square meters in size. m, regardless of their purpose. You can use the device at weddings, celebrations, holidays, in kindergartens at matinees, summer discos or New Year discos . The device is portable, so it can be installed in any convenient place.

Color music strobe DRIVER MAX is a light and music strobe with a speaker mounted inside the body, which, in addition to playing 7 color music modes, plays tracks from a USB flash card. One installation is enough to illuminate a room up to 200 square meters in size. m. The device is suitable for organizing a wide variety of parties and celebrations. The GALAXY Note model also has a built-in speaker, reproduces seven light and music modes and can be controlled remotely. The technology can set the rhythm of a party in a house, apartment or other small room.

Sets of strobe lights for discotheques

Strobe light kits are a ready-made solution for organizing concerts, discos, parties and other events.

Sets of strobe lights with color music are intended primarily for professional use, but nothing prevents consumers from using them for private parties and celebrations, as well as corporate evenings. Our company offers customers three options for lighting equipment sets that include stroboscopes.

Strobes for home disco

Stroboscopes-color music for home disco "Friendly Party" This set includes 2 stroboscopes, a disco ball and a laser projector. A disco ball is a light and music technique that reproduces program light patterns for musical accompaniment. It is able to immerse all event participants in the atmosphere of a nightclub. Laser color music is a device for creating lighting effects and stage lighting. With this kit you can create the atmosphere of a nightclub in any room or outdoor area.

Stroboscopes for clubs and cafes

Set of strobe lights for home and cafe “Big Holiday” - a set with two strobes, a laser projector and a smoke machine. The devices have a panel for controlling light fluxes, adjusting the flicker frequency, color selection, combining and smoothly changing shades, as well as turning on a strobe light. With the help of equipment you can create a mood of celebration and fun at any event. The kit is used in any conditions, and the maximum effect is achieved if the equipment is installed in nightclubs and concert halls where artists and various musical groups perform.

Strobes for stage

Stage Lighting Kit - RGB strobes kit with spotlights, lasers and fog machine. Suitable for stages of clubs and cafes, as well as small theaters and cultural centers. Powerful RGB LEDs produce bright lights and create excitement at any event. Spotlights are equipment for lighting dance floors. The devices also have a control panel. With its help, you can adjust the flicker frequency, select the color of effects, combine shades and activate the strobe.

The equipment supports the DMX-512 option; they are connected to DJ consoles, forming a single network with other lighting devices.

RGB strobes

LED RGB strobes are cutting-edge lighting technology that creates numerous dynamic effects using white and red colors. The devices have maximum light output and a wide beam angle. RGB strobes can be used in any environment, for a wide variety of events in clubs, bars, restaurants, concert halls, outdoor areas, as well as at home when organizing private parties. The online store has two models in its assortment that are in greatest demand among consumers.

Disco spotlight SUPERMAX-550D is a universal club device that is perfect for home, summer discos and entertainment events in small restaurants, bars and cultural centers. The device can be used in conjunction with other lighting equipment or separately, thanks to the built-in microphone that is sensitive to sound. The peculiarity of the technique is in variations of more than 5 colors and dozens of different color music combinations. The device supports the DMX-512 function.

The SUPERMAX-500D DMX RGB strobe light is also suitable for any entertainment event. The device has more power, so it is able to project lighting effects in large rooms or outdoors, where it is more effective than other models. The strobe can work separately or in accompaniment with other lighting equipment, thanks to the DMX-512 option.

We recommend the device for theme parties, New Year's discos and other mass entertainment events. And also for filling stages, podiums, theatrical productions and performances of artists.

Rotating strobes

Rotating strobe heads combine a strobe, a disco projector and a scanner. The device can rotate 360°, vertically – up to 270°. This guarantees a wide beam coverage that other spotlights cannot provide. Rotating heads have different speeds and directions of rotation, luminous flux power, number of colors and shades. In most modern models, the listed parameters can be adjusted remotely using a DMX remote control. The service life of the devices is from 40,000 to 100,000 hours, which makes them one of the most durable among lighting equipment.

The equipment is in demand in all entertainment establishments, especially in clubs where discos and concert halls are held, where large or small events are organized, star performances and other show programs are held. If desired, swivel heads can be used for private parties, holidays and corporate events.

Powerful strobe light at a low price

We offer customers two models of rotating heads with strobe function . The Moving Led Rotating Wash Head includes 7 RGB LED lights that provide flood light as well as an even white glow. The presented device is most often chosen by professional DJs and nightclub owners, regardless of the size of the dance floor.

Free smoke machine for any disco strobe light

The Spot Supermax Moving DMX-512 rotating head is an incredibly practical device that is used everywhere - in bars, restaurants, nightclubs, etc. The device is capable of creating 56 lighting effects. They are formed thanks to 7 colors and 8 patterns. Special connoisseurs of club lighting can purchase equipment for home discos.

Free smoke machine for any disco strobe light

The advantage of stroboscopes is that they have a DMX option, which provides programming of the stage and lighting effects, and the ability to connect equipment around the entire perimeter of the hall/stage to the DJ console. The rotating head has RGB LEDs with a total power of 30 W, as well as 9 built-in patterns that are projected using a Fresnel lens.

Rotating strobes for discotheques

To organize a bright and high-quality entertainment event, it is necessary to use a strobe, which is capable of realizing a lighting effect within a 360° radius. Such devices include stroboscopes made in the form of rotating heads.

The importance of devices can hardly be overestimated, since they complement any show, even if it is a summer party, a disco in a community center, a performance on the stage of a theater or a musical concert in a philharmonic society. The technique is based on a rotating gobo wheel, which ensures a scattering of light rays around the entire perimeter of the room.

Choose high-quality models of equipment on our website. The Spot swivel head with strobe function is an exceptionally bright, lightweight and economical LED spotlight. Equipment power 50 W. It is quite sufficient for holding small and large events, including summer discos in open areas, in the forest or in nature.

The Gobo RGBW rotating head with strobe function is a more productive and powerful device that is often chosen for large clubs and concert halls where popular bands perform. Equipment is no less in demand when holding public events in open spaces. The rotation angle of the model is 540/270 degrees.

The SPOT Wash DMX-512 rotating head with strobe is an incredibly practical model designed for universal use - stage, restaurant, club, home, apartment, etc.

Rotation angle: 540/270 degrees. The device responds well to sound and can work independently or in conjunction with other lighting devices.

LED strobes LED effects

To make any show effective enough, you need to pay maximum attention to lighting. In addition to purchasing classic lighting equipment, it is advisable to buy a device that creates bright lighting effects. Such devices include LED effects with a strobe .

Such equipment generates several types of light beams and supports a stroboscopic function. The devices are installed above the dance floor, stage or place where an entertainment event is planned. The equipment is characterized by its light weight and compactness, which ensures ease of installation.

LED LED effects JD System Orion Double - the device provides a powerful and dynamic RGBW LED effect, supports 4 clusters, a dimmer and a fast strobe effect.

Technical characteristics : The strobe device is equipped with a DMX option (1, 4 or 7 channel control mode). Super Orion LED effects – the device has 4 matrices of 9 1 W LEDs (8 red, green, blue and 12 white). They are formed by a fan of bright colored rays. Control is carried out using DMX 1 and 3 channels. Sound animation and the ability to use built-in programs are provided.

Disco strobe MOONFLOWER 7 was developed for professional use in large entertainment venues and concert halls. The power of the device makes it possible to provide lighting effects to large venues and stages where musical groups perform and pop stars give concerts.

"Advantages" of factory devices

Before you decide to purchase a standard factory strobe, you need to study in detail all its features and learn about the principle of operation. So, let’s first understand the scope of application of this device. A device called a strobe light allows the car owner to easily adjust the ignition. Having this device at hand can significantly speed up the entire setup process. Equipped with a lamp, the unit gives signals about the presence of a spark, so you can quickly and correctly set the required ignition timing.

It is impossible not to note the efficiency and accuracy of efficient factory instruments that can cope with this task in just a few minutes. However, despite such advantages, for some reason the vast majority of car enthusiasts try to create such a unit with their own hands, without rushing to buy a production version. Most likely, this aspect is due to the rather high cost of stroboscopes. The overwhelming majority of factory models are equipped with expensive gas-discharge lamps, the subsequent replacement of which becomes equal in price to purchasing a new device. Commercially available factory analogues are sold in the price range from 1000 to 6000 rubles (a simple Multitronics will cost the buyer 1000 rubles, Astro L5 at 1300, Focus F1 at 1700, and Focus F10 at 5600 rubles).

If desired and the need arises, you can create such a device yourself, you just need to find all the materials that include the simplest and most ordinary things that are in everyone’s garage. A simple car strobe light can be made from a flashlight, LEDs, and even a simple laser pointer. Despite its almost complete pricelessness, a hand-made device will be able to serve no less durable and reliable, proving the effectiveness of the service in practice.

Using the device

To set the advance angle (moment) with your own hands, use a device to illuminate the setting marks while the car engine is idling. One of them is located on the rotating parts of the car engine (on the crankshaft pulley or on the flywheel). The second mark is stationary, it is located either on the cover of the front part of the car’s cylinder block, or on the gearbox housing. If in the light of the device the movable mark appears to be opposite the stationary mark, the car’s ignition is normal and does not require adjustment of the timing (angle) of advance.

If the marks do not match, to adjust the timing, you need to change the position of the distributor accordingly. To delay the ignition timing, you need to turn the distributor in the direction of rotation of the slider, and to do it earlier, in the opposite direction. If sparking in your car is controlled by a microprocessor, look for a faulty sensor or entrust the solution to this problem to professionals.

With a strobe light, setting the ignition on a carburetor engine is always much more convenient than “by ear”. But the price tags for such equipment sometimes “bite,” which pushes many motorists to alternative solutions to this issue, for example, by making a strobe light with their own hands.

How to use this strobe light

Using a garage-made strobe, you can easily and with great accuracy:

• set the ignition on a carburetor engine;
• check the spark plug or ignition coil;
• check the operation of the centrifugal and vacuum ignition timing regulator.

Homemade strobe is cheaper and more reliable

In order for the ignition timing to be set correctly, it is necessary to assume that the mixture is usually ignited a couple of degrees before the piston reaches the top stroke point. This angle is called the “ignition timing angle”. As the crankshaft speed increases, the SOP should also increase along a given curve. As a result, the advance angle is set at idle and then controlled in all engine operating ranges up to 5000 rpm.

When connecting a strobe, you need to wind its sensor (copper wire) directly onto the sheath of the high-voltage wire of the first cylinder of the internal combustion engine. Three or four turns will be enough. In this case, it is necessary to fix the wire in this way as close to the spark plug as possible - in order to minimize the influence of neighboring wires on the operation of the strobe. To power the device, its wires with “crocodiles” cling to the terminals of the battery. For better visibility, you will also have to additionally mark the flywheel mark with a white dot - paint or, for example, a clerical touch.

Installation of UOZ:

1. Start the engine and warm it up to operating temperature, leaving it idling within 600-800 rpm.
2. Connect the strobe power wires.
3. Wind the copper sensor wire onto the armor wire of the first cylinder.
4. Point a flashlight, flash, laser, etc. to a fixed mark (located on the timing case).
5. Then find the same moving point on the flywheel pulley.
6. If the moment is violated, the moving and static marks will be relatively far from each other.
7. By rotating the ignition distributor housing, ensure that the marks match and fix the distributor in this position.
8. Next, you need to briefly raise the speed, as a result of which the marks will diverge again. But it normal. In this mode, the ignition is set earlier. To check this indicator, a pair of fixed marks are provided - after 5 degrees of ignition timing.
9. For 3 thousand rpm, the SOP in the case of VAZ engines is 15-17 degrees.
10. To check the serviceability of the spark plug, alternately wind the copper wire onto the high-voltage wires and see if there are any missing pulses. A lower frequency of LED flashes will indicate a misfire, “punching” the spark plug into the housing.