How to repair a retractable suitcase handle with your own hands: what to do when the handle breaks along the way?

How to repair the telescopic handle of a suitcase in an emergency?

The best way to repair a suitcase is to take it to a workshop, where they will certainly put it back on its feet, or rather, on its wheels. But what if you need to repair the retractable handle of your suitcase urgently, right during your trip? And craftsmen sometimes charge so much for their work that this money would be enough to buy a simple replacement for a broken suitcase. If you are not too worried about the aesthetic appearance of the case, you will be able to repair it, even if you are very far from nuts and bolts. How exactly can this be done? It all depends on the degree of damage.

Suitcase repair

A suitcase in the 21st century is a rather complex design with a combination lock, a large number of fasteners for each compartment, and also on wheels. Even the handles are retractable for ease of transportation. A modern suitcase for the owner is convenient for travel and reliable in use.

A good suitcase serves as a clear marker of wealth, because their cost is high. But even the best suitcase can fail at the most inopportune moment.

In Vakhrushev's Workshop, suitcases are repaired using modern materials from Russian and foreign companies. We carry out post-warranty repairs of suitcases of all brands. To achieve this, the workshop equipped workplaces with new equipment and the necessary spare parts.

The suitcase always breaks at the wrong time

On a long trip, a suitcase often breaks down right at the station or during baggage claim at the airport. The wheel falls off, the handles do not extend, or the clasp does not open.

At that moment you remember that it was necessary to repair the squeaking wheel or the sticking retractable handle in advance. To avoid these small problems while traveling, go to Vakhrushev’s Workshop to have your suitcase repaired.

High-quality repair is the principle of work

Our workshop repairs travel suitcases of any complexity and at the highest level of quality. Over the years of fruitful work, the craftsmen have accumulated extensive experience in replacing handles with any type of fastening and retractable ones, replacing or restoring wheels is also our specialty.

For high-quality repair of a suitcase, original spare parts are required, since repairing a suitcase handle is difficult, due to completely different types of fastening the handle to the body for each brand.

Types of repair:

• wheel replacement;
• Retractable handle replacement;
• replacement for a regular handle.

When wheeled suitcases require repair, it means that the bearing or holder has failed.

Contact us, the specialists at Vakhrushev’s Workshop will be able to carry out repairs of any complexity.

Even if you need to repair suitcases, replacing wheels is also not difficult, because we have a large database of spare parts.

Having sent your favorite suitcase to Vakhrushev's Workshops for repairs, you will soon receive back a completely restored suitcase.

If the handle breaks on the road...

When the handle breaks right on the road, there is no talk about the beauty and durability of the repair. It is important to do everything quickly and relatively reliably: so much so that you don’t have to drag your suitcase in your hands to your destination. And a real pro of express repairs – tape – will help us do this.

So, the most common problem is a fracture of one of the tubes of the retractable handle. In terms of DIY repairs, the situation is very similar to applying a splint to a person with a fracture.

1. Find a rigid frame that will act as a tire. This may be a small metal pipe, but in the field you usually have to rely on a pencil, ruler or comb - the stronger, the better, of course.
2. An improvised splint is applied to the fracture site along the pipe.
3. Now the fracture site is wrapped with tape or tape along the entire length of the tire or at least 5-7 cm in each direction from the fracture.

Of course, it will be impossible to put the handle and tire back together, so if you still have to check your suitcase as luggage, limit yourself to simply wrapping the break in several layers of tape.

Not everyone takes adhesive tape or electrical tape with them on trips (but in vain!), so the short-sighted will have to try to replace this irreplaceable product with improvised means: a handkerchief, cling film from sandwiches, office clips, if they fit the size.

By the way, this method can be used even if the handle has broken in several places, practically crumbling. You’ll just have to find a slightly longer tire or increase their number, and you’ll need to wrap it with tape more securely.

Table functionality

A folding table made of wood is very durable and is not inferior in convenience to ordinary furniture. It can be used as a writing desk, a lunch desk, for children's activities, or for crafts. If you think about the decor, it will fit well into the interior of the room. As an option, you can make your own table with folding legs, which will take up little space during transportation.

Another plus: it is ideal for small spaces; if necessary, it can always be folded and hidden in a closet, thereby freeing up space in the room. Some models easily fit into the trunk of a car, which is very convenient - you can take it with you while traveling.

And you don't have to buy it. Making a folding wooden table with your own hands is not at all difficult. The article presents drawings and describes the main stages of work.

This is a simple design. The most important thing is to prepare all the components and process them efficiently. The dimensions indicated in the drawing give an idea of ​​​​the dimensions of the entire structure and individual elements.

How to fix a pen at home?

So you brought your broken suitcase home, and now you have enough time to slowly deal with the problem and try to repair the telescopic system yourself. Let's say right away: without experience in welding and polishing metal, it will not be possible to make the handle look like new, so all aesthetes will have to go to workshops. But if you only need functionality from a suitcase, you can improve the method of strengthening the break by replacing the tire with a pin.

• Unscrew the bolts of the telescopic structure and remove the broken part.
• Insert structural reinforcement into it in the form of a metal rod slightly smaller in width than the cavity itself.
• Secure the broken area with the same tape or tape.
• Secure the reinforced structure back with bolts.

If the fault allows, you don’t even have to unscrew the pipe from the telescopic holders, but it is important that the length of the pin is equal to the length of the handle itself, otherwise your reinforcement will dangle inside.

Another possible problem that you can solve yourself is unscrewing the bolts holding the structure and, as a result, the handle dangling from one or both sides. To repair it, it is enough to tighten these or put new bolts and nuts in place of the old ones, for which you need to get to the frame from the inside through the upholstery.

If it is not the telescopic handle that has unscrewed, but the stationary handle, you can also secure it with a bolt and nut, if it has not been mechanically damaged (not cracked or broken into pieces)

Choose suitcases with telescopic, stationary and side handles, so that if one or even two of them break, you have a backup transportation option.

To watch online, click on the video ⤵

Telescopic leg of a feeder chair, DIY chair Read more

HOMEMADE SUPPORT FOR THE LEGS OF A FISHING CHAIR OR PLATFORM Read more

Telescopic Feeder-Arm, do it yourself. More details

Do-it-yourself telescopic leg for the attachment table Read more

DIY leg telescope Read more

Universal platform for fishing. Aliexpress Read more

Homemade telescopic leg for fishing platform D30 More details

DIY mini platform for feeder. More details

DIY mini platform. Finished and finalized. Part 2 Read more

Legs 36 for a fishing platform with your own hands More details

COMPONENTS FOR HOMEMADE LEGS OF FISHING CHAIRS AND PLATFORMS. More details

DIY platform Read more

Do-it-yourself collapsible stool for feeder fishing. More details

Telescopic legs, do it yourself! Tests. More details

DIY fishing platform Part 1. Read more

Telescopic legs for a fishing chair. (with your own hands) More details

Do-it-yourself mount for a feeder chair Learn more

DIY fishing platform Read more

Source

A quick way to wedge a handle

The second most common problem with telescopic systems after their fracture is jamming inside the suitcase. This is especially unpleasant if the suitcase is heavy: you won’t be able to carry it on wheels!

• To begin, feel inside the frame through the upholstery for the frame of the handle. Your task is to find holes with springs that secure it.
• Now you need to press these springs simultaneously: the handle will release and “shoot” out of the groove.

The opposite situation is also not uncommon: the handle refuses to fit back into the groove, and the suitcase must be checked in as luggage. Unfortunately, it is almost impossible to solve this problem without disassembling the structure. In order not to completely break the structure during transportation, you can try to dismantle it completely with your own hands, tightening the bolts under the upholstery from the inside, or ask someone more experienced to do this for you. Then pack the pen in a suitcase, and wrap the suitcase itself with packaging film so that things don’t fall out through the hole and get dirty.

The telescopic handle and its quality are almost the main criterion when choosing a suitcase. Give preference to wide handles made of strong and thick metal, and then the likelihood of them breaking will be lower.

To avoid having to repair the telescopic handle, just roll the suitcase by it, and do not carry it, do not sit on the suitcase, and do not stuff it with heavy things under the maximum permissible weight. Well, if a breakdown does occur, now you know how to deal with it in an emergency and at home without the need to resort to the help of a specialist.

To watch online, click on the video ⤵

HOMEMADE LEG SUPPORT FOR A FISHING CHAIR OR PLATFORM More details
Homemade leg support for a fishing platform More details

Support for a homemade leg for a carp chair, feeder platform. More details

Do-it-yourself telescopic leg for the feeder platform. More details

COMPONENTS FOR HOMEMADE LEGS OF FISHING CHAIRS AND PLATFORMS. More details

SUPPORTS FOR CHAIRS AND PLATFORMS FOR ALL OCCASIONS. CATCHING. More details

Telescopic leg of a feeder chair, DIY chair Read more

HOMEMADE FISHING CHAIRS, PLATFORM, CHAIR. ALL THE INFO IN ONE ROLLER. More details

CHAIR SUPPORTS OR PLATFORMS FOR LOOSEN SOIL FROM. WHAT HAPPENED. More details

Homemade telescopic leg for fishing platform D30 More details

Do-it-yourself platform chair Read more

Legs 36 for a fishing platform with your own hands More details

My version of the body kit for the feeder chair Read more

Manufacturing Pedana for feeder chair Read more

Fishing chairs, armchairs, platforms. What to sit on when fishing. [salapinru] Read more

DIY mini platform for feeder. More details

Homemade support for a carp chair, part 2. More details

Telescopic legs for a fishing chair. (with your own hands) More details

ONE IDEA FOR A DIY FISHING CHAIR. More details

Source

Broken handles and how to fix them

Sometimes the toughest suitcases break. If the model is branded and of high quality, then breakdown may occur due to improper operation or overload. Moreover, the fault of the breakdown does not always lie with the owner. Airport baggage handlers may handle luggage carelessly.

Most often the handles break. Repairing a suitcase on wheels with your own hands, if the rivet securing the handle is broken, proceeds as follows.

• you need to find the mounting location from the inside;
• prepare the necessary tools - M 4 screw with a cone head (or another suitable one), 2 nuts;
• Insert a bolt into the hole of the broken fastener and tighten it from the inside with a nut.

For reliability, tighten another nut well on top.

How to repair a suitcase on wheels yourself, if there is no suitable workshop nearby, your ingenuity will tell you. Even if a breakdown occurs while traveling, you can use available materials. For example, use a belt:

• with one, or better yet, 2 belts, you need to pull the product lengthwise in 2 places;
• in the place where the broken handle is located, you need to insert an oblong object that will replace it.

No belts? They can be replaced with rope. In this case, the repair system does not differ from the previous method. If there is no item nearby to replace the handle, then it can be made from the rope itself. To do this, you need to twist the string and wrap it with adhesive tape at the bottom, leaving a rope ring as an impromptu handle.

Damage to a telescopic handle for a suitcase or a retractable handle is difficult to eliminate in “field” conditions.

The easiest way is to purchase a new telescopic handle and replace the broken one with it. Of course, repairs can be made by contacting specialists, but this is quite an expensive pleasure. In emergency situations, you should try to fix the breakdown yourself. This requires tools and skills to work with them.

To replace a broken handle with a new one, you need:

1. Dismantle the old one. To do this, you need to gain access to its fastening mechanisms. If the lining does not have a zipper, it will have to be cut.
2. Inside, at the bottom of the suitcase, there are 2 tubes attached to screws that need to be unscrewed.
3. Unscrew the same screws on top of the product, in the inner part (there can be up to 5 pieces).
4. Remove the handle from the top. Sometimes its upper part is attached to the suitcase with latches; they need to be disconnected using a screwdriver.
5. A replacement part is installed in place of the broken handle. Sometimes the mounting holes for the new handle are in a different place, and therefore you will have to carefully tighten the screws or bolts in the new places.
6. Fasten the lining.
7. Do-it-yourself repair of the telescopic handle is completed.

The algorithm for repairing a retractable suitcase handle with your own hands is as follows:

1. Unscrew the screws on the sides of the telescopic tubes to remove the handles.
2. Drill holes in the corners with a drill equal to the diameter of the screw or bolt used.
3. Drill through holes in the handle itself, in the places where the factory screws were.
4. Flush with the surface of the handle, you need to fuse, using a soldering iron, a screw with a screwed nut. Before doing this, widen the hole for the nut so that it fits in there with difficulty.
5. Remove melted plastic from the handle with a knife or file.
6. Glue the broken corner with Moment glue.
7. Attach the corners of the handle with screws and washers.
8. Insert the repaired handle into the telescopic tubes and secure with a pair of self-tapping screws.

This sequence will help when the handle breaks off from the telescopic tube at the place where it is fixed.

Let's sum it up

Table legs are a functional device that determines the quality of the entire piece of furniture that you use for eating, working or other needs. Be careful when choosing and creating them, then you will be able to enjoy the fruit of your labors for many years.

Not a single apartment is complete without a dining table, and even modern bar counters cannot completely replace this traditional attribute. It is installed in kitchens or dining rooms; its dimensions and materials depend on the desires and financial capabilities of consumers. How to make a dining table with your own hands? Read in the special article.

In children's rooms, to create a warm and cozy atmosphere, parents prefer to install tables with multi-colored legs in bright colors, for example:

The legs can be anything, the main thing is that they perform their functions and you like them

As you can see, seemingly simple details from a full-fledged piece of furniture can seriously diversify and dilute the atmosphere in the room.

Fault prevention

To avoid breaking the suitcase handles, you need to follow some rules:

• load the suitcase evenly with things;
• place the heaviest items down;
• avoid overloading;
• carry the suitcase only by the stationary handle;
• Transport the suitcase using the telescopic handle only on level roads.

These simple rules and tips will help you restore suitcase handles yourself and avoid such troubles in future use.

How to repair a retractable suitcase handle with your own hands

In the accelerating pace of modern life, we increasingly have to travel: for work, family reasons or just for leisure. In all these cases, a suitcase is required. It became an indispensable travel companion not long ago, but immediately gained popularity due to its maximum comfort in use.
But even the best quality suitcase can fail after extensive and long-term use. What should I do if the retractable handle is broken and can I repair it myself?

What to do when the handle breaks along the way?

The most unpleasant case would be a breakdown right during the trip, when you need to transport things right away, which means you won’t be able to turn to professionals. In addition, their services, especially those provided near train stations, airports and other places where travelers stay, can be greatly overpriced.

There's no need to worry. It is quite possible to put the pen in order yourself, even without any special skills.

Important! Please note that the proposed actions will be temporary. After all, on the road it is not the appearance of the suitcase that is important, but the speed and ease of correcting the situation.

The easiest way that can be used in any situation is to wrap the handle with tape or tape . You will also need any solid object that will act as a frame. For example, a pencil or any metal pipe. You can do without it if you have to fold the handle and check the suitcase as luggage, but the reliability of the repair will be significantly reduced in this way.

You should not skimp on tape;
the handle should be wrapped in several layers along the entire length of the improvised frame , in extreme cases, a few centimeters on both sides of it. To avoid running out of available supplies, always take tape with you when traveling and make sure you don’t run out of it.

How to fix a retractable suitcase handle with your own hands

When the journey is over, you need to look for a way to fix the broken part for the long term. This can be done at home, but the handle, again, will not look exactly the same as before it broke. If the appearance of your suitcase is important to you, it is better to contact specialists who will fix it better and more beautifully. But not everyone wants to spend money on something they can fix themselves.

If you don’t want to carry the suitcase to the workshop, then prepare a metal pipe with a slightly smaller diameter than the cavity of the handle. An additional material will be the already familiar adhesive tape or tape. Nothing else will be needed for repairs.

First you need to unscrew the bolts on the structure and remove the damaged elements from it. The metal pipe is then inserted into the cavity and reinforced inside. Make sure that nothing is loose or in the way, otherwise the repair will be of little use. Therefore, it is so important to choose a rod of the exact diameter that is ideal for your pen. Once you are sure that everything is in order, you can seal the broken part with tape or tape. The last step is to return the handle to its place and tighten the bolts.

Important! Tighten the bolts as tightly as possible, because this determines how long the breakdown will not occur again and the suitcase will not turn into a burden instead of being a faithful assistant in transporting things.

If the stationary handle breaks, it can be put in order by simply tightening the bolts, but only when it was not severely damaged - it did not break or crack.

It is best to choose suitcases that have several handles, so that if they break down and you don’t have the necessary materials on hand, you can deliver things to their destination.

How to quickly wedge a handle?

It may also happen that this part of the suitcase simply jams at the most inopportune moment and will not open.
In this case, the suitcase loses almost more than half of its advantages, because now you have to carry it in your hands, which causes extreme inconvenience. If this happens, you should try to feel the frame through the upholstery of the product. If you manage to find the place where the springs are located, then after several attempts to press on them, the handle will probably open. You need to be as careful as possible so as not to damage the structure, and also remember that the release will be sharp and can lead to injury to you or people standing nearby.

It happens that the handle, on the contrary, does not want to fold.
Then there is no other option but to unscrew the bolts and remove it completely. The resulting hole must be sealed, because through it you can lose or damage the things folded inside. When choosing a new suitcase, always pay attention to the quality of the telescopic handle - the thicker it is, the less likely it is to break. The metal from which the structure is made is also important.
As a preventive measure, you should follow a few simple rules for using a suitcase - do not sit on it, do not lift it by the telescopic handle, and do not load it with too many things.

It is important to know its maximum permissible weight and try not to exceed it , because this significantly affects the condition of the handle. It is also recommended to initially purchase a high-quality item, so that in the future you do not have to constantly waste time and effort on constant repairs of the product.

Posts 1 page 30 of 999

Share12/104/2014 15:44:16

Mike, Fiestvod explained everything correctly

If you have any additional questions, please ask. It’s very interesting what happened. I read it and thought about it. I need this too!

Edited by Kafolya (04.12.2014 15:48:01)

Share204.12.2014 16:32:20

Share304.12.2014 16:35:37

If you post photos as links, then I think this one will do - https://radikal.ru

Share404.12.2014 16:50:58

Edited by Freemason (04.12.2014 16:59:10)

Share504.12.2014 16:51:48

I read it and thought about it. I need this too!

Here's the thread with the clip I stirred up.

Share604.12.2014 17:06:35

It's true. Deaf winter for the feeder

And for me it’s doubly important, I gave a reel to a friend, broke off the clip. Now I’m scratching my turnips.

Share704.12.2014 17:17:41

Are you going to use a brass one or donate an old plastic one??

Share804.12.2014 17:18:59

And it’s very interesting what happened.

I'm interested myself. On the weekend, not earlier

Share904.12.2014 17:52:30

Edited by Freemason (Today 16:59:10)

Thank you, although they may not even pay attention to the link ((.

Share1004.12.2014 17:55:21

Thank you, although they may not even pay attention to the link ((.

Well, in my opinion, there are great opportunities - look more carefully in the final phase (I’m used to laying this out like a villager) Sorry for the flood.

Share1104.12.2014 17:59:05

I want brass. I don't want plastic. Only when I go to the market to buy rivets

The weather is not suitable for flying.

Share1204.12.2014 18:50:29

Will you build a brass fence?

I want brass. I don't want plastic. Only when I go to the market to buy rivets

The weather is not suitable for flying.

Alexey, you still need to “look for” them. Those rivets from which I made clips, I bought from former YuMZ-eshniks, on the market (Topol-Varus). But now they (the rivets) are no longer there. They are not on the car market either. Problem .

Share1304.12.2014 18:58:04

It's true. Deaf winter for the feeder And for me it’s doubly important, I gave a friend a reel, broke off the clip Now I’m scratching my turnips.

You and Sergei Doka_60 live in the same city.

Share1404.12.2014 19:07:28

It's true. Deaf winter for the feeder And for me it’s doubly important, I gave a friend a reel, broke off the clip Now I’m scratching my turnips.

You and Sergei Doka_60 live in the same city.

Alexey, you still need to “look for” them. Those rivets from which I made clips, I bought from former YuMZ-eshniks, on the market (Topol-Varus). But now they (the rivets) are no longer there. They are not on the car market either. Problem .

Only brass or copper Zhiguli ones will do, I also previously posted photos of the clip conversion. The difference is that the spring will pass through the hollow part of the rivet.

Share1504.12.2014 19:22:35

Yes, you and I have already talked about this. There’s no way I’ll be able to go to the flea market. It wasn’t necessary in the summer, but now it’s snowing

As soon as the snow melts, I’ll go and look for it.

Only brass or copper Zhiguli ones are also suitable.

Thanks, I'll definitely take a look. Also, Dima, Seryozha, what was the lining used for?

Edited by Kafolya (04.12.2014 19:24:31)

Share1604.12.2014 20:12:41

Misha, I see that Fiestvod has already painted everything perfectly. Nothing to add. You just need to remember where on your computer you save the photo you want to post. And yet, before attaching it (photo 3 from Fiestvod), you can view it by right-clicking on the selected file and selecting “view”.

Share1704.12.2014 20:18:25

Yes, you and I have already talked about this. There’s no way I’ll be able to go to the flea market. It wasn’t necessary in the summer, but now it’s snowing

As soon as the snow melts, I’ll go and look for it. VDA wrote:

Only brass or copper Zhiguli ones are also suitable.

Thanks, I'll definitely take a look. Also, Dima, Seryozha, what was the lining used for?

Edited by Kafolya (Today 19:24:31)

You won’t believe it, from a paint cap in a can. Yes, you can from any plastic, more or less elastic. As long as the thickness is suitable. Well, not everywhere a backing is needed. If the place for the clip is not deep, then without a backing. I just have a couple of rivets left, I need to change something else. Otherwise I would do it for you. If you find the rivets, bring a reel, I’ll do it for you.

Share1804.12.2014 20:23:14

I'll keep it on mind

Share1904.12.2014 20:23:51

Also, Dima, Seryozha, what was the lining used for?

Made from fluoroplastic tape 0.2 and 0.4 mm. At our factory, they insulate transformer windings with it.

By rivets. Zhigulevskie ones for attaching clutch disc friction linings to classics (in any case, I riveted them with the same ones on a VAZ-2102). You need to carefully look at the boxes from sellers. The hat should be flat. Like this

Share2004.12.2014 20:35:39

Share2104.12.2014 20:43:34

By rivets. Zhigulevskie ones for attaching clutch disc friction linings to classics (in any case, I riveted them with the same ones on a VAZ-2102). You need to carefully look at the boxes from sellers. The hat should be flat. Like this

Dima, yes, these are copper rivets for the Zhiguli friction linings. But now they are also not easy to find. They save and make hollow tubular IRON ones. But the seeker will find them.

Edited by Doka_60 (04.12.2014 20:44:23)

Share2204.12.2014 21:07:03

VDA Post photos on piccy.info. Unlike a radical, the photo does not disappear over time.

Share2304.12.2014 23:53:41

VDA Post photos on piccy.info. Unlike a radical, the photo does not disappear over time.

Types of components

There are a large number of breakdowns that can occur in any suitcase, regardless of the manufacturer, design, or model of the product. Even the most minor problems, for example, damage to a zipper or clasp, can cause a lot of discomfort or even make it impossible to use this important attribute for travelers. To carry out repairs, as well as replace individual parts or entire structures, appropriate spare parts for a suitcase on wheels are required. Among the main components of a travel bag are the following elements:

• retractable systems;
• wheels and wheel blocks;
• pens;
• legs, stands;
• locks, cases;
• runners;
• lightning.

Obviously, fittings for suitcases are presented in a wide range and it is advisable for the owner of such a thing to understand the design of the product. This will help not only to correctly localize and diagnose the breakdown, but also to repair or replace it yourself without high costs.

What needs to be replaced

Travel bags are prone to breakage or wear, both individual parts and the entire structure as a whole. This is due to the special operating conditions of suitcases on wheels, during which they experience stress both from the weight of the luggage and from driving on various surfaces. And many structural elements can deteriorate or even fall off and get lost. However, not all parts are subject to replacement and repair; in some situations it is easier and faster to purchase a new product instead of one that has become unusable.

The following spare parts are subject to repair, which, by the way, are easy to find on sale or make yourself:

• retractable mechanisms;
• handles are stationary, retractable;
• wheels;
• wheel blocks;
• stands and legs for suitcases;
• locks, zippers, fittings.

Spare parts, like the suitcases themselves, are made by many manufacturers, which means they can have different prices and quality.

Rules for selecting elements

In most cases, finding a similar replacement part is not difficult, especially when it comes to popular brands and models. In some situations, components that are similar in appearance and parameters and are capable of performing all the necessary functionality may well be suitable. However, sometimes it may be necessary to resort to alternative options, purchasing or independently producing elements of a completely different type.

So, what should you pay attention to when choosing parts for a suitcase:

1. Size. Many replaceable elements can be similar in parameters, for example, zippers, wheels, legs. It is important to accurately measure all the necessary dimensions and select a suitable analogue.
2. Material. Components can be made of plastic, rubber, metal or fabric. Often, some types of materials can be replaced with higher quality ones. For example, plastic legs on metal ones with a rubberized base. However, in some situations, due to the design features, replacing the material with a more durable one may not be practical.
3. Load. A suitcase is a product that is subject to various types of loads during operation and even transportation. Any part has a tensile strength and the amount of load it can withstand without deforming or collapsing. Most of the load in a suitcase on wheels is directed to the lower support or moving part. Therefore, special attention should be paid to the technical characteristics of such parts.
4. Visual component. The shape, color, texture of original and replacement parts may be different. Sometimes this is acceptable, but in most cases the suitcase can look awkward.
5. Brands. In cases where the traveler owns a high-quality product from a well-known brand, it is necessary to purchase spare parts from the same or an equivalent manufacturer. If you use parts that are inferior in quality and characteristics to other structures, the likelihood of another breakdown only increases.

Using improvised devices

It is not always necessary to spend time making technically complex supports for the hearth. You need to be creative and just look around. We are surrounded by many interesting things from which we can make original and exotic legs with a minimum of effort.

You are offered the following options for a non-standard approach to making barbecue legs:

1. Using a sewing machine stand. In the last century, in our country and in neighboring countries, sewing machines were installed on supports that were made of artistically curved metal. At the same time, the basis for the technology was distinguished by decent strength and reliability. People often simply throw away such things or recycle them. You need to come to a scrap metal collection point and thoroughly examine the contents of its warehouses. There is a high probability of finding the right thing. All that remains is to fit the stand under the hearth.
2. Assembling an original support from old water pipes left over after renovation. They can be bent, cut, twisted and welded without much difficulty. A thoughtful and creative approach allows you to create the most incredible compositions from pipes, characterized by durability and uniqueness. You can revive the structure by applying fireproof paint.
3. Creation of original and lightweight folding legs from aluminum. The source of raw materials for the work are old cots, tourist and country furniture made of aluminum tubes.

An excellent solution in all cases is the use of forged products. The simplest jewelry can be made yourself using sheet copper or brass, a hammer and a hammer. To decorate the legs at a higher level, you will need to visit a specialized store.

How to replace it yourself

In most cases, you can repair trolley bags with wheels yourself, without contacting a service center. How to do this is described step by step below.

When working with sharp cutting edges, machines with rapidly rotating parts, heavy tools and other dangerous objects, you must follow safety regulations. In some cases, it will be necessary to protect hands, eyes and face from various dangerous and harmful factors.

Retractable handle

The most common type of failure associated with a retractable handle is the failure of one of the telescopic tubes. The shank of the corners that are attached to the part may also break off.

When carrying out repairs, it is necessary to disconnect the telescopic tubes with the retractable handle. To do this, you will need to unscrew the parts on the sides using a self-tapping screw. Let's consider a common case when the shank of one of the corners breaks off. Finding a replacement is very difficult, so repairs will be carried out using improvised means as follows:

1. The shank to the corner will be attached simultaneously with the base of the handle. This can be done using a screw or a long self-tapping screw.
2. If there is no suitable fastener, you can go to an alternative option and use a screw with a head that matches the diameter as much as possible, for example, M4. If necessary, additional flat washers are installed.
3. In order to avoid relapse, it is recommended to simultaneously perform similar manipulations with the second corner.
4. In the handle itself you will need to make through holes with a diameter corresponding to the fastener.
5. Now screw the nut onto the screw and use a soldering iron to fuse it flush with the surface of the handle. The resulting melted plastic is removed with a blade or smoothed with a file.
6. The corners are fixed directly to the crossbar using pre-prepared screws and washers.

Next, you need to insert the handle shanks into the telescopic tubes, then secure the structure with two self-tapping screws.

Legs made of brick and stone

This material is used in the construction of stationary frying complexes. Stone and brick supports are highly durable and reliable. When deciding on the choice of such material, the owners of the site are guided by its presentability. A stationary barbecue complex harmonizes well with a brick house, paving stone paths and platforms and alpine slides.

In order for the stone supports to maintain a vertical position, it is necessary to build a foundation for them. It is made in the form of a monolithic slab or individual blocks.

Making brick supports on a concrete foundation requires the following tools and materials:

• roulette;
• level;
• Bulgarian;
• Master OK;
• shovel;
• cement;
• sand;
• crushed stone

To build a stone hearth stand, you need to follow these steps:

1. Make a foundation. After marking, holes are dug 40-80 cm deep, depending on the type of soil. A cushion of sand and crushed stone is poured into the hole, and a reinforcement frame is installed. Concrete is poured, compacted and leveled.
2. After laying the waterproofing, supports are erected. The optimal width is 1 brick. The height is selected based on the size of the fireplace and the height of the cook.

Grills without legs, which are made independently or purchased in specialized stores, are attached to the erected base. If necessary, the stone is finished with plaster or fire-resistant tiles. If the cladding will not be used, it is recommended to treat the brick and seams with hydrophobic impregnation to protect the material from moisture.