how to make a gun out of paper
Do you enjoy doing crafts with your kids? Teach your boys how to make a paper gun with their own hands , this is a great alternative to plastic toy guns. And anyway, someone needs to stop the constant clutter of plastic toys filling children's drawers.
Kids will love this idea because making a paper gun is super easy and quick, and who doesn't like quick results? And if it’s also a paper gun that shoots , then the enthusiasm will increase significantly. The article presents several models of paper pistols and even a paper gun , which are ideal for children's crafts. Make a home shooting range and announce a competition for the best shooter. Just explain to your children that you can’t even shoot cats and dogs with paper bullets.
slingshot
This may be familiar to you because many of us played with it in our youth. Some of us might even break the window glass of our house by doing this. As you can see, it has the potential to be an effective personal protective equipment, and just like in the old days, we can still make one for our protection and safety. It's actually very easy to do and only takes a few steps to start using this effective weapon to protect yourself. Prepare Y-shaped wood, 1 x 2 inches of leather, rope, and a piece of rubber/surgical tubing.
Find a Y-shaped tree, but you can also get any tree and cut it. Take your gum and then attach each end to the ends of the tree using string. Make sure you tie them well and then cut the center of the rubber. The next thing to do is drill two holes at the end of your leather before cutting the rubber where you cut both ends. Attach them with your chain. For a projectile, small rocks work very well. This weapon can be taken anywhere with you, ensuring that you have a small weapon to help you defend against an attacker.
How to make a paper gun that shoots: 4 main methods with photos and videos
- Roll the tube into 4-5 layers for the handle.
- Fold it in half.
- Bend the free edges of the workpiece at an obtuse angle.
- Fold a small piece of paper into quarters.
- Wrap it around the resulting handle to tighten it.
- Insert the ends of the tape one into the other.
- Roll two tubes of cardboard or thick paper. One should be almost half the length of the other.
- Insert them into the resulting pocket of the handle so that the end of the tubes is under the tape.
How to make a paper gun that shoots? The A4 sheet must be folded into 2 equal parts and cut along the fold line. Both halves need to be folded horizontally, you will get rectangles in which one side will be much narrower than the other.
Now you should unbend the sheet. You should press the edges to the fold, fold it in the center, getting a narrow strip of 4 layers of paper. On the second half of the paper, you need to bend it vertically in the center, and bend the corners of the rectangle at right angles. The edges of the product must be bent inward to create an angle of less than 90 degrees.
To make a handle, the resulting triangle should be folded in half and then rolled to form a blank in the shape of the letter L. Fold the 2 parts to form an obtuse angle: spread the handle a little, thread the paper through the resulting holes. Secure the model with paper clips and pull the resulting tongue at the bottom to make a trigger.
Cut a triangle above the handle to match the groove on the top of the barrel. A notch is required on the front of the barrel for an elastic band. Pull the elastic so that it covers the entire model - from the front of the barrel to the handle.
A bullet can be made from a ball of paper, making shooting a safe activity: glass and fragile objects will not be damaged, and there will be no bruises from such shooting. When you pull the trigger, the rubber band is released and the gun fires, hitting the ball of crumpled paper.
You can modify the product to make it seem more realistic - decorate it with drawings or appliques, as your imagination tells you.
✅ I play bubble kvass
Protests in Kazakhstan. Journalists were shot at their feet. Where is Nazarbayev located?
Why did Kazakhstan explode? / Editorial special issue
Does Putin rule Kazakhstan?
Results. Special issue
A MANIAC IS PLAYING WITH US. THEY COULD NOT PASS THE TEST AND SAVE THE VICTIM
Semyon Uralov about the rebellion in Kazakhstan
Breaking news from Kazakhstan! 01/08/2022 (12:00)
Heads or tails ? Coin Solve Challenge!
Breaking news from Kazakhstan! 01/08/2022 (14:00)
The dead guardsmen were buried in the Karaganda region
35 BLOGGERS CAME TO AMKAL / MERCEDES GIVEAWAY for my Birthday!
Ex-adviser to Nazarbayev accused the Kazakh special services of betrayal and where Elbasy is now
Kazakhstan: consequences of pogroms | What happened to Almaty and other cities
White sister in reality! Sonya has turned into the Ventriloquist's servant!
Watch new, popular videos online in good quality. Quickly search for any video.
How to Make a Paper Gun That Shoots Paper - watch video online
For the handle we make a tube, as in the first step, only we make it thicker and shorter compared to the first tube. We secure it with tape. We cut off the part that will be adjacent to the trunk at an angle. Glue both parts together with glue.
Expert opinion
Strebizh Viktor Fedorovich, leading construction foreman
One of the advantages of any gymnastic exercise, and such squats are partly gymnastic, is that it contributes to the development of overall flexibility of the body. If you want to clarify something, please contact me!
Weapon Lubrication
If the barrel is not lubricated regularly, it will promote rapid galvanization. Therefore, after each cleaning, lubricate the weapon, following this algorithm:
- We select a cleaning rod to match the size of the barrel and lubricate it with gun oil. The best option is a bottle with a spray bottle; it will allow you to apply the oil evenly and not overdo it with the amount. Choose a product with silicone: it lubricates mechanisms that are usually difficult to reach.
- We lower the cleaning rod into the barrel and lubricate the weapon. The part must be kept in a vertical position, and also make sure that there is not too much oil on the cleaning rod - it should not drain.
- After lubricating the barrel, pay attention to other parts of the gun. To lubricate them, you can use a soft thin brush.
After the product is oiled, check to see if you have used too much oil. To do this, take a couple of test shots - if a large amount of smoke is released, this is a sure sign that you have gone too far. Some of the oil must be removed using a powder puff or rag. If you do not do this, over time, plaque will form in the barrel of the weapon.
Safety precautions when upgrading
Although air guns are considered non-lethal, their bullets have significant penetration and can seriously injure a person. Even a slight increase in bullet speed can significantly increase its traumatic properties. Thus, an increase in speed by 20 m/s, with an initial value of 100 m/s, increases the shot energy by almost 1.5 times.
A separate article is the resulting power of the weapon - if after acceleration it exceeds 7.5 J, this is fraught with legal consequences.
After the upgrade, it makes sense to calculate power by measuring the speed and mass of the bullet. The energy of the shot is equal to the product of the mass of the bullet (in kg) by the square of the velocity (in m/s) divided by two.
When deciding to increase the power of your pistol, pay attention to safety precautions:
- too strong a spring in the PPP can lead to deformation of metal parts when arming and cause a premature shot;
- the increased speed of the bullet makes it dangerous at long distances. When using a “pumped” pistol, pay special attention to the absence of people in the direction of shooting;
- Do not allow excessive thinning of the walls of the discharge chamber when boring. This reduces the overall rigidity of the structure and can cause injury if gas escapes through defects.
Of all the types of pneumatics, spring-piston pistols are the least susceptible to modernization. This is facilitated by the small volume of the pneumatic chamber and the difficulties that arise when using more powerful springs.
Carbon dioxide pistols have more acceptable acceleration characteristics, and the champion is pre-inflated pneumatics. Do not forget about the established limit of 7.5 J, so as not to become a victim of your own creativity when it falls into the hands of law enforcement agencies.
With pre-pumping
Diagram of the modernized Crosman 1377 air pistol
Tuning for higher speed in pump pistols has much in common with modifying CO2 pistols. The general method is to judiciously increase the length of the barrel. You can also use the following approaches:
- reducing valve spring stiffness. This increases the time it takes for the gas to escape from the chamber and increases the speed of the shot;
- boring the valve holes (see above);
- increasing the stiffness or length of the mainspring driving the trigger;
- work on the gearbox in models equipped with it. If the gun does not have a pressure regulator in the pneumatic chamber into which the gas enters after the main cylinder, the reducer will have to be removed and adjusted manually.
The price for increasing the power of the shot is an accelerated decrease in pressure in the cylinder. If the goal of modification is only to increase the speed of the bullet, then you can experiment with the gearbox being as open as possible, avoiding its excessive spinning.
Cleaning weapons correctly
After you have purchased all the necessary tools, you can begin cleaning the weapon. As we have already said, it is necessary to clean the gun after each use. For this:
- We perform partial disassembly of the product - if you have not done this before, you can read the instructions for the gun or watch a video on Youtube;
- We clean the barrel using a product specially designed for this purpose. Do not overdo it: the cleaning product is usually based on kerosene, the residue of which is difficult to remove.
Gun oil Ballistol spray, 100 ml
Buy gun oil Ballistol spray, 100 ml
This composition is intended for cleaning firearms, gas and pneumatic weapons. With its help, the barrel bore, parts of the gas reloading system and the gas exhaust mechanism are cleaned of powder deposits and lead. Ballistol is a universal oil that protects metal and wood products. Capable of removing hardening, deposits of lead, copper and tombac from barrels, chambers and other metal parts of weapons, including firearms. The oil will also protect the wood parts. It can be used to clean, soften and impregnate holsters, shoulder straps, and belts.
Composition for removing carbon deposits and lead Huntex premium, 100ml
Buy composition for removing carbon deposits and lead coating Huntex premium, 100ml
This composition is designed to neutralize and remove combustion products and lead coating of the barrel bore, gas release mechanism and parts of the reloading system of all types of firearms. Has good dissolving ability. Contains active alkaline components. The composition effectively cleans surfaces from contamination, having a gentle effect on the metal. Huntex premium contains no mechanical impurities or inorganic alkalizing agents.
- After treating the barrel with a cleaning agent, go over it with a brush. Choose a plastic or metal model, depending on the degree of contamination of your gun.
- The barrel can then be rinsed in soapy water. Dishwashing detergents are also suitable for this purpose: with their help it is easier to remove kerosene and shavings that inevitably form during the cleaning process. You can use a cleaning rod - it will definitely remove dirt.
- Finally, we dry the barrel naturally in a warm room or near a heating radiator. Remaining water is removed using a powder puff or rag.
After cleaning, be sure to lubricate the barrel with gun oil. We’ll look at how to do this correctly in the next paragraph.
History of creation
History of the discovery and use of the principle of projectile throwing
by exposing it to compressed air has its roots in Ancient Egypt and South America. Pneumatic weapons acquired their recognizable image today in 1430, when the German gunsmith Hutter made the first.
That is why Germany is considered the birthplace of pneumatics.
The operating principle of Gutter's invention was approved and taken up by others. Centuries of refinements and improvements began, and in 1607 the first gas-cylinder pneumatic systems appeared.
At this time, air guns are a luxury item, given as gifts to kings and queens.
In 1653-1655 the first pistols and guns were made,
the design of which included an air cylinder.
In 1790, thanks to improvements, they were able to fire a series of shots from a gun equipped with a compressed air cylinder. At the same time, the first “shooting canes” appear
– a pneumatic weapon disguised as an accessory.
Surely you will also like the material about choosing an air pistol according to.
Since the 18th century, pneumatics have become increasingly popular and widespread and begin to be used not only for hunting, but also as a military weapon. are now quite acceptable. In Europe, the first weapons companies began to emerge in place of individual workshops.
In 1880, a foundry opened in Barcelona to produce
lead bullets, and later the company’s flagship became the creation of Gamo air guns. The well-known German airgun production company Carl Walther GmbH Sportwaffen was founded in 1886. For example, she releases .
The American company Crosman Arms Company was founded in 1923
and today remains one of the leaders in the production of pneumatics and accessories. The company produces .
In July 1942, the history of the Russian Izhevsk Mechanical Plant begins. It was opened for the purpose of producing military weapons. In 1949, production of sporting small arms began. And in 1990, the plant produced the legendary IZH-53M, a spring-piston pneumatic pistol.
Surely everyone has heard about the famous Colt 1911 pistol, about it.
Advantages and disadvantages of PPP
The advantages of PPP are:
- Ease of use - pneumatic guns are often used in outdoor shooting ranges; even children shoot from them.
- Reliability of the mechanism, fault tolerance due to the simplicity of the design.
- Availability in terms of price.
- Inspection and repairs will also not require large expenses.
- Cheap one shot.
- Relative noiselessness.
- Power at close range.
- Stable air pressure ensuring a constant bullet exit velocity.
The disadvantages of spring-piston pneumatics include:
- Single-shot - if the model does not have automatic equipment, then to fire a new shot you need to reload.
- Recharging takes a lot of time.
- Strong recoil, as a result, decreases shooting accuracy.
- It is impossible to install simple sights, since recoil can cause the fragile lens to become cracked.
- Large mass of an air pistol.
- Inadmissibility of a blank shot.
- When left in a charged state for a long time, the spring and/or cuff become unusable.
- The target firing range is 10-15 meters.
Spring piston dart thrower
Manufacturing difficulty: ★★★★☆
Production time: A couple of days
Materials at hand: ██████████ 100%
One day in the village I got bored and decided to make another shooting thing. I was very limited in materials and tools, so after digging around for several days in the backyard and local trash heap, I made a spring-loaded piston rifle dart launcher, from which I can easily hit a beer can from 20 meters. It all started when I found a spring in the backyard.
- Aerosol can
- Wooden cylinder
- Bike tube rubber
- Sheet metal or plastic
- Insulating tape
- Nail 15cm
- Spring (I don’t know what it’s from, I found it)
- Thick board
- Metal or plastic tube
- Wood planks
- Nails
- Steel or plastic tube (barrel)
- Rope
- Metal washer
- Emery or file
- Lathe (you can try a drill)
- Scissors
- Adhesive for rubber
- Drill
- Jigsaw
- Pliers
- Cold welding (POXIPOL)
- Insulating tape
