How to make a jigsaw from a sewing machine with your own hands?

Sewing machine as a jigsaw

The heir to a grandparent's estate often gets an old sewing machine.
It has already served its purpose for sewing clothes, since more precise equipment is now being produced. If you don’t have a jigsaw on your household, you don’t have to spend money on buying one. It is made with your own hands from a sewing machine. Procedure:

Remove the thread weaving device. It is usually located at the bottom of the machine and secured with two bolts. Dismantle the cotter pin and the drive shaft, which leads to the thread weaving mechanism. Unscrew the top panel, which serves as protection for the mechanisms. The slot for the needle is expanded to match the parameters of the file

It is important that it passes freely through the hole and that there is still a backlog of 2-3 cases. The file is being modernized. For installation in a needle holder, the length of the file should not exceed the permissible length of the needle intended for installation in the machine

To do this, the upper teeth are ground off, and the lower part is sharpened like a point.

Now the jigsaw for curly cutting on plywood is ready. It will be more difficult to work with a manual drive because your legs will get tired. An additional disadvantage will be vibrations from force on the tool. The electric drive of the machine, converted into a jigsaw, partially solves the problem of vibrations.

An expensive jigsaw can be replaced with a homemade design. It will not be inferior to anything in terms of quality and functionality if you approach the assembly process responsibly

It is important to make high-quality plywood mechanisms that serve as a support table. It is desirable that the table be able to rotate

For the version with a sewing machine, this will not be possible. If desired, markings are applied to the table to make it easier to measure parts during work.

DIY sewing machine: primitive models and tips on how to build a machine (100 photos and videos)

Every needlewoman should have a sewing machine, and also have at least the slightest skill in repairing it with her own hands. It happens that the device begins to tear the threads or a knock appears during operation.

If problems arise, generally you only need adjustment or minor repairs to the sewing machine, you can try to do it yourself.

However, if complex repairs are needed that require replacement of elements, then it is better to leave such work to a specialist.

The most important part of the device is the needle. During operation, it makes several thousand punctures in fabric of any density. Therefore, the needle often becomes dull, which leads to a lot of stress on it, as a result it can break or bend.

If the needle accidentally hits a hard surface, for example, the body of a machine or a rigid element of a clothing fastener, its tip becomes bent.

After this, the needle looks normal, but during the work process an uneven stitch is obtained. This occurs due to the fact that the thread catches on the broken end, passing through the eye of the needle.

As a result, the top thread of the stitch is longer, which slows down the sewing process. Because of this, the thread constantly breaks and loops appear in the screed.

Often, equipment fails when the craftswoman uses fabrics that are not suitable for a given model of device.

It turns out that repairing a sewing machine with your own hands involves such an action as replacing the needle. This part should be given special attention and the needle should be replaced as often as possible, even when no defects are identified.

An improperly installed needle can also cause equipment to malfunction. The blade should be turned towards the shuttle spout. If the thread begins to tangle, you need to remove the needle and check that it is correctly fixed.

DIY jigsaw from a sewing machine (6 photos)

Those who do figure cutting will probably find a homemade jigsaw from a sewing machine useful. In this case, it is best to use an old sewing machine with a working mechanism. Today on the Internet you can find many diagrams and drawings of similar devices on this topic, they all have practically the same design.

If a sewing machine is taken as the basis for making a jigsaw, then all that is left from it is a flywheel with a groove for transmitting torque and a vertical rod, the one used to attach the needle. Plus, the design is complemented by a small electric motor, on the shaft of which a pulley and a gear belt are installed. A little history about the jigsaw The first mention of the jigsaw dates back to 1946. It was then that the famous Swiss engineer Albert Kaufmann came up with a brilliant idea to replace the needle in a sewing machine with a small file

In that century, this invention received considerable popularity and public attention. Of course, modern jigsaws have a fundamentally different design: they are lightweight, mobile, and also have more power

As for a jigsaw from a sewing machine, this option will be useful only when cutting out shapes from plywood, and not for cutting chipboard and thick boards. How to make a jigsaw from a sewing machine with your own hands The design of a homemade jigsaw from a sewing machine is quite simple, it consists from the following parts: The base on which the sewing machine is installed; An electric motor that transmits torque via a belt drive; Crank mechanism; A movable frame with a file (you can refuse to make it); Springs. The advantage of this kind of homemade work from a sewing machine is that it minimizes rework. For example, the crank mechanism of a sewing machine is already connected to a movable mount, through which the needle is fixed. The mount itself can be easily modified to accommodate the installation of a jigsaw file or any other suitable size. Let's look at a clear example of how you can remake a Soviet sewing machine to suit the needs of figure sawing. To make this homemade product, you will need: Sewing machine; Bolt and nut; A metal plate with a spring to make a tension device (in some cases this may not be necessary); Two metal corners. The above components, if necessary, can be replaced with others, as well as the design of the jigsaw itself. To complete all the work, you will need the following tools: Drill with metal drills; Screwdriver and pliers; Bulgarian; Tap for cutting internal threads First of all, it is recommended to remove all unused parts from the sewing machine, leaving only the crank mechanism with the needle holder in its place. To install a saw tension device on a future jigsaw, you will have to dismantle the shuttle mechanism of the sewing machine

An important note: if an electric motor is already installed in the sewing machine, then you should not get rid of it, since it will be used as the main drive. To install a thin saw on a sewing machine, it will be enough to drill a small hole in the upper mount

To install a wider blade, the hole must be drilled to a suitable diameter. When making the lower fastening, you can use a regular bolt and nut. To make a hole in a nut for a bolt, you should use a tap whose diameter should match the diameter of the bolt. At this point, the modification of the sewing machine is almost complete. In order not to carry out figure cutting manually, an electric motor (45-50 W) should be installed on the side of the sewing machine pulley, on the shaft of which a pulley will also be attached. To transmit torque, you will need to connect the electric motor pulley to the sewing machine pulley using a belt.

Material taken: Here

Universal jigsaw machine

The ability to install different saw blades - for example, standard ones from a manual jigsaw and thin ones (from a jigsaw machine) allows you to significantly expand the range of work performed.

We bring to your attention a universal homemade wood cutting machine, which is designed for cutting both straight and shaped cuts due to the fact that you can install different files.

Moreover, it is very simple to make it - without any drawings. You don't even need a welding machine. We will use boards and wooden blocks as the main material.

Step one: making a desktop.

From boards 20-25 mm thick we glue a shield measuring 40x60 cm (as an option, you can use a sheet of plywood). Then we saw off four wooden blocks of 30x30 mm, 30-35 cm long.

We screw the prepared wooden blocks to the shield. We reinforce the joint with gussets made of plywood or wood. As a result, we got a desktop with legs.

For greater rigidity, we make a strapping of wooden blocks in the lower part of the legs.

Step two: making the stand.

At the next stage, we saw off two wooden blocks and connect them at an angle of 90 degrees. We strengthen the junction with scarves.

As a result, we got an L-shaped stand that needs to be screwed to the desktop. Then we make markings and drill a hole in the table for the saw blade.

Step three: installing the jigsaw.

The jigsaw is mounted under the work support table. The sole of the tool is fixed with metal clamps with a bolted connection.

Step four: assembly of the entire structure.

So we have come to the final stage of work on assembling a homemade jigsaw machine from an electric jigsaw.

After installing the L-shaped stand and the jigsaw with the saw blade, it is necessary to make a mount with a block of bearings that will hold the saw in the desired position.

Please note: the mount must be removable and therefore must be able to be quickly secured using wing bolts.

For a thin saw blade for figured cutting, a mount of a slightly different design will be used - see photo below.

You can watch step-by-step instructions for making a jigsaw from an electric jigsaw with your own hands in the video below. The idea was shared by the author of Hobi Market.

Scroll Saw and Jigsaw Table in The One Machine

This homemade design has a lot of advantages.

Firstly, it is versatility and practicality. Secondly, ease of manufacture and assembly. Thirdly, there is no need to use welding and an electric motor. Fourthly, the jigsaw, which is used as a drive, can be removed at any time and used for other work.

How to make a machine from a sewing machine?

A sewing machine makes an excellent jigsaw, which is equipped with a saw blade movement regulator. It is not difficult to do if you follow these instructions:

1. The thread weaving mechanism is removed from the bottom of the machine. On some models it may be located in a different location.
2. To dismantle this unit, you need to remove several bolts, then remove the cotter pin and drive shaft.
3. The top protective panel is unscrewed. After this, the groove along which the sewing needle moves must be expanded to suit the parameters of the file.
4. The cutting element itself is also slightly modified. It is trimmed according to the length of the sewing needle.
5. It is not necessary to make an adapter to install the cutting element. Instead, you can grind down the upper incisors a little and process the lower zone of the blade.
6. The file is inserted into the needle holder and work begins.

All presented options for manufacturing jigsaw machines are very successful. The resulting units are distinguished by high labor productivity, and making them is not at all difficult. Depending on their skills, each master will be able to choose the best model of homemade equipment.

Video: Jigsaw from a sewing machine

In the life of a home craftsman, from time to time the need arises to make figured and simply decorative cuts, including inside the workpiece. Gasoline, circular and conventional hand saws cannot cope with this task due to their design features. To solve this problem, use a manual jigsaw, specially designed for performing such operations. This tool undoubtedly copes with its task, but when working with large volumes or dimensional materials, it definitely loses to its more professional brother - a jigsaw.

Purchasing a brand new, shiny, and functional benchtop jigsaw is absolutely effortless. Store shelves are filled with products from various manufacturers aimed at professional and amateur work. At first glance, the stationary jigsaws on sale seem to be very complex in terms of design, the assembly of which is carried out only by selected expert technicians. In fact, these are quite simple devices that you can make yourself, if you have the desire and step-by-step instructions. And if the first point depends only on you, we will definitely help with the second and provide detailed instructions on how to independently assemble a homemade jigsaw machine.

Basic steps

The first thing to do is remove the flywheel to which the belt is attached.

After this, on the other side you will need to remove the front cover covering the needle bar. Next, the presser foot rod is removed, after which all parts under the needle plate are removed. Including shuttle travel.

If the car is old and you intend to paint it, you need to immediately remove all the old paint. Afterwards you will need to sand the surface.

The strawberry harvest will increase many times: we water the bushes in the spring with garlic fertilizer

The appearance of the tomatoes will tell you everything. Choosing the right fertilizers

This is against logic: why a child cannot manipulate his parents

It is advisable to treat the entire body in this way.

The next step is to remove the needle bar. In its place you will need to install a longer rod from the presser foot. The bottom bracket will need to be cut, otherwise it will not be possible to secure the saw blade.

As a result, there will be one hole left at the end of the rod, which will be used to secure the blade with a screw.

Since there is no hole in the presser bar to connect to the crank mechanism, it will need to be drilled. The screw will be screwed in there.

After completing the described steps, you will need to make a guide for the file. It will support the canvas in the desired position.

The guide is installed on the sole of the machine. To make it, 3 bearings will be enough. Two of them are needed to hold the file from the sides. The third blocks the movement of the canvas towards the edge.

American husband Mika Newton: how the singer, who emigrated to the USA, lives now

How to determine when you can collect birch sap: rely on the weather

The man thought he got a mini-pig: the pet “did not meet” his expectations

The base of the guide must be bent from the strip on which the rods machined to the inner diameter of the bearings are fixed.

Under the sole of the machine there are eyelets that were previously used to attach mechanisms. The strip must be shaped so that it can be secured in these eyes.

Remaking the place where the needle is attached to the file

Not everyone and not always has the need to carry out only figured cuts. Much more often, a jigsaw is used to produce controlled cuts in straight and round shapes. In such cases, a thin file will be too slow, but a standard jigsaw blade will cope with the task quite quickly. And everything would be fine, but such a saw will not fit into a standard needle holder. This means that you need to reactivate the logical hemisphere and “pump up” your homemade jigsaw from a sewing machine. By the way, this is quite simple to do.

As an example, let's take a product from the following author, although this problem was also solved at the end of the previous manual. The answer lies in the stitching of the seat to tighten the needle. For this purpose, a grinder with a metal disc is used. The shank of the file itself also needs to be sharpened so that it fits into the hole in the fastener element with the bolt. Detailed examples are shown in the photo above, below, and also in the video.

Disadvantages of a manual jigsaw

A manual jigsaw is designed to form even cuts. In this case, as the rollers, rod, and pusher wear out, the saw may wobble, deviate from a straight line, and change the angle of attack. Regardless of the quality of the tool components, the following features are always present:

1. When the saw becomes dull, deviation from a straight line is observed when cutting material of uneven density (for example, low-quality chipboard). The saw is capable of leaving the cutting line when it encounters a knot in the wood.
2. When trying to make a curved radius cut, you can observe the following picture: the upper cutting line, which the worker follows, follows an exact trajectory, the lower one deviates, goes to the side, the radius becomes larger. The higher the wear of the tool and the lower the sharpness of the saw, the more pronounced this phenomenon is.
3. Some materials cannot be worked using a pick-up or bottom feed of the saw. The carpenter is required to move the tool forward extremely evenly, which is impossible to do very accurately; as a result, the saw beats along the entry and exit path.

It is even more difficult to work with thin saws designed for curved cuts. Without practice, it is very difficult to achieve a good result, especially on thick slabs or wood materials. Let's look at how you can make a carpenter's job easier and the result better.

Manual sewing machine for leather: do it yourself for only $2

Anyone who has ever worked with leather knows that stitching it with a regular sewing machine can be very difficult. When using an electric sewing machine, you risk not only breaking the needle, but also burning out the motor. You have to stitch it manually, pricking all your fingers. This is a very long and tedious process. We invite you to make your life easier and make your own hand sewing machine for leather, durable and reliable.

Content :

Continued modernization of the sewing machine

After all work on the stem is completed, the metal cover is screwed into place. You can go to the other side of the machine. Here a pulley from a washing machine with a diameter of 20 mm was used, which came from nowhere among the trash in the garage. However, finding such a part for someone who decides to repeat my modification will not be difficult. Many people are getting rid of old washing machines. As a last resort, there are social networks in which people will be happy to get rid of faulty equipment, subject to pickup, even for free.

A plastic pulley was installed in place of a metal wheel, which the seamstress rotated by hand while working. The pulley fits into place very tightly, after which it is screwed on with the original bolt with a very wide head.

To insert the pulley, you will have to tap it a little with a hammer.

Spacer for the car: what and how to make it from

Now it was necessary to make the machine stand higher - after all, the original rod was extended. For this I used a piece of chipboard countertop. It was cut to the shape of the base. The holes were marked using regular paint and drilled.

The spacer is ready, all that remains is to screw it into place

Having screwed the spacer to the base of the sewing machine, I decided to add a little aesthetics, so it was painted black to match the former tailor's work tool. It turned out pretty good. While the paint was drying, we could work on the bed for our stationary electric jigsaw.

The spacer was painted black to make the resulting unit look more aesthetically pleasing

Stationary jigsaw from an old sewing machine

From an old sewing machine that has long since expired, the author suggests making a simple stationary jigsaw with your own hands.

It can be installed in the garage and home workshop. However, you will additionally need to make a desktop from plywood or chipboard.

Using a homemade stationary jigsaw, you can cut various shaped blanks and parts for any crafts from wood or sheets of plywood.

An electric motor is used as a drive. You will also need a quick-release chuck for jigsaw files.

Main stages of work

First of all, you need to remove all unnecessary parts from the old sewing machine. Then you will need to slightly shorten the rod with the quick-release chuck.

Then you need to drill a hole in the marked area. You will also need to drill one hole in the stem of the sewing machine itself.

At the next stage, you need to connect the sewing machine rod with the rod with the jigsaw chuck.

Next, using a hammer, the plastic pulley from the washing machine will need to be carefully placed on the shaft of the sewing machine. From chipboard (or plywood) you need to cut a base for a sewing machine.

At the last stage, all that remains is to make a desktop and attach the electric motor under it. The detailed process of making a stationary jigsaw from an old sewing machine can be seen in the video on the website.

Rate this post

Source: https://sdelairukami.ru/statsionarnyj-elektrolobzik-iz-staroj-shvejnoj-mashinki/

General assembly instructions

Craftsmen often assemble their jigsaws from an ordinary home drill or from a refrigerator compressor. Thus, a manual jigsaw is converted into an electric tool. Some use a washing machine motor. An interesting solution is to create a jigsaw machine using an old sewing machine.

Making from improvised materials

You can use any available household power tool as a motor: a screwdriver or electric drill, which has a spindle speed regulator, is perfect. You can use materials that are at hand: wooden blocks, unnecessary sheets of plywood.

The main thing, from the point of view of safety, convenience and productivity, is the bed. It is made from plywood sheet with a thickness of 15 mm. The wooden parts are connected with screws. For increased reliability, the joints can be coated with glue.

A lever assembly is assembled from wooden blanks. Levers must have good strength. The most suitable tree is beech or oak. You can use straight sections of legs from old chairs.

The tips of the levers are sawed longitudinally. The nail file fasteners are inserted into the cuts. The fastening is a regular metal plate with two holes. The thickness of the plate is 2-3 mm. The mount is screwed to the lever through the upper hole, and the jigsaw blade is clamped through the lower hole. Wing nuts are used for clamping.

The lever system is fixed in the frame. The back of the levers is connected to each other by a lanyard. Or, in other words, a screw tie. It is desirable that the levers are parallel to each other.

The crank assembly is cut out of plywood up to 1 cm thick. The axis of rotation is designated using bearings. The bearings themselves are seated in holes that are drilled in the racks.

Then the flywheel and lower arm are made. They are connected to each other by a connecting rod, which is also made of plywood. After which the work table and rotating mechanism are assembled. A rotating arc is cut out of thin plywood, in which a slot is cut. The table is installed on the bed. The structure is tightened with a wing nut. The drive can be an electric screwdriver.

Approximate design diagram:

Conversion from a hand jigsaw

The first step is to make a working table for the mechanism. A metal sheet or thick plywood is suitable for these purposes. Holes for the cutting tape and fasteners are drilled and sawed out in the worksheet.

The jigsaw table is then placed on a regular table. Once secured, the guide rails can be assembled. To reduce vibration, simply cut a rubber pad of the desired size and place it between the jigsaw table and the main surface.

The above design is convenient in that it can be easily disassembled and can be used again as a hand jigsaw.

Since the standard device has springs that tension the saw, a rocker arm is necessary. One edge of the rocker arm is attached to the cutting element of the machine, and the second is under tension from springs. These simple steps will easily turn an ordinary jigsaw into a machine.

When operating the device, it is important not to forget to turn off the pendulum stroke before starting cutting.

Assembly from a sewing machine

You can also quickly and easily assemble a homemade jigsaw from a sewing machine. Moreover, this device has an interesting feature - a regulator for the stroke of the nail file, since sewing machines have a speed switch.

First, at the bottom of the machine you need to find a thread weaving knot. To do this, several screws are unscrewed. The cotter pin located inside is knocked out and the drive shaft, which is connected to the thread weaving complex, is removed. After completing this procedure, the top panel is unscrewed. The groove along which the needle rode widens slightly to accommodate the saw blade. The files themselves are shortened slightly to the length of the needle. To fix the saw itself, you can make an adapter. But the easiest way is to grind off the top part of the cutting blade and sharpen the bottom. After which you can insert the nail file into place of the needle and get to work.

When working with jigsaws of any type, you should not forget about safety rules. Do not leave the device turned on for a long time without supervision.

If the master has long hair, it is better to pick it up or use a special cap. It is better to roll up the sleeves of your clothes. The room should be well ventilated. In the room where carpentry work is carried out, a first aid kit with emergency aid for cuts must be kept.

Connecting the electrical components of the machine

Connecting an electric motor cannot be called complicated, however, there are some nuances here too. As you know, there are 2 switching schemes - “star” and “triangle”. Each of them has both pros and cons. For the jigsaw, I chose the “star” and now I’ll explain why. Such a circuit ensures a smoother start-up, without strong surges in the current load, unlike the “triangle” one. Of course, in this case the power drops by about 30%, but this is not critical, I am not going to cut thick metal. Those who decide to repeat my project should take this point into account.

When connecting an electric motor, situations may arise where connections cannot be avoided. You should not use self-clamping terminal blocks, such as “WAGO” for them. Such elements may not withstand inrush currents. It’s better to make a regular twist, solder it and insulate it. For this I used heat shrink tubing.

We insulate connections using heat shrink

Installing a button

The START button was installed on the right hand in the corner of the tabletop. This arrangement is most convenient when working on the machine. Everything is connected here extremely simply - 3 phases coming out of the engine are switched to 3 contacts of the start button. On its reverse side, power will be supplied from a 380 V network.

Attach and connect the start button

Design features

The design diagrams of all jigsaw machines are usually the same. Having carefully examined the drawings where this tool is depicted, you can see the following structural components:

• the bed, which is also often called the body. It is designed to accommodate all structural elements of the unit;
• drive mechanism;
• crank mechanism. It is necessary to convert the rotational energy of the motor shaft into the movements of the saw used during operation;
• double rocker arm. Equipped with fasteners for a file and a tension device;
• Desktop. In some modern models, it has a rotation mechanism that moves to a given angle.

The working principle of a jigsaw machine

A jigsaw machine is designed for cutting sheet materials or boards along a pre-designated contour. Unlike most machines, it is capable of performing not only straight, but also curved cuts. The operating principle of the machine is to create a characteristic movement of the saw blade, fixed on opposite sides. The main elements of a jigsaw machine are:

Figure 1 – Elements of a jigsaw machine

• Desktop;
• frame or bracket with a tensioning mechanism;
• electric motor;
• crank mechanism.

When the engine starts, the crank mechanism converts rotation into reciprocating motion, which is transmitted to a frame with a tensioned file.

The workpiece is placed on the work table and fed to the cutting tool.

The master visually controls the direction of the cut and corrects it by turning and changing the feed direction, which allows for accurate and clean cutting along a given contour.

The length of the file, as a rule, is significantly longer than that of manual design options, which allows you to work with thicker workpieces (with certain limitations). Working with a jigsaw is more precise and accurate, allowing for increased productivity and quality. At the same time, an open saw blade creates a risk of injury and requires compliance with safety regulations.

DIY jigsaw from a desk

Another option, how to make a jigsaw with your own hands, is a little more complicated than the previous one, but it is also more practical and convenient. To do this, you will need an electric jigsaw, which will make the work as easy as possible. To build the machine you need: any old desk, a jigsaw (will serve as a power unit), a hand jigsaw and plywood (for making arcs and rods).

Note! Absolutely any model of electric jigsaw can be used as a power unit.

The process begins with the manufacture of a “swing”, which at one end will connect to the mechanism of the electric tool, and at the other will hold the file. The jigsaw is fastened with self-tapping screws under the table cover. A round hole is made in the lid so that the file can move freely in it and dust and shavings do not get stuck. The swing is installed above the power tool, and a saw is fixed between them.

One end is attached to the jigsaw, and the other is attached to a wheel at the end of the swing. The start pedal operation is very simple. To do this, a product is formed from a metal plate with a hook at one end and a fastener at the other. The hook is placed directly on the start button of the tool, and the other end is attached to a wooden plank that will serve as a pedal.

Homemade jigsaw from hand tools

The designs and drawings of the homemade jigsaw options presented online are different. This is due to the imagination of the authors and the desire to make a device that will stand out from the rest. Only the concept is the same in most cases - they take a manual jigsaw as a basis and repurpose it.

Home woodworking enthusiasts often look for information on how to make a jigsaw with their own hands without any special skills. You can use a ready-made manual jigsaw as a base. The mechanism does not require careful modification. The factory manual device is a drive. But the crank mechanism will have to be developed independently. Manufacturers are trying to offer consumers platforms for quick remodeling, but personal needs can only be satisfied with their product.

DIY jigsaw from a sewing machine

If you have an old sewing machine on hand in fully working order, then it can easily be used to make a homemade jigsaw, and even a small sharpener. The essence of converting a sewing machine into a jigsaw is to install a fabric holder instead of a needle.

In this case, the design of the sewing machine itself is of no small importance. So, if an old sewing machine with a foot mechanism is being converted into a jigsaw, then there is no need to install a small 40 W motor

Otherwise, you will have to install an electric motor on the sewing machine, since the quality of cutting workpieces largely depends on the required force and uniformity of saw movement.

In this case, the motor is installed on the tabletop, near the stand of the sewing machine, as close as possible to the flywheel. Since a belt will be used to transmit torque, a pulley should be installed on the electric motor shaft, after which it will need to be connected via a belt to the pulley of the sewing machine. Thus, you can convert a manual sewing machine to operate from an electric motor.

Now you will have to tinker a little with installing the adapter for installing the jigsaw file. As a rule, the socket into which the sewing machine needle is fixed is too small to install a jigsaw blade, so it will have to be drilled out a little and deepened at the same time. In general, a lot here depends on a particular device of the sewing machine.

If using the method described above to install a jigsaw saw on a sewing machine does not work, then there is another suitable option. For these purposes, you need to use a nut with a hole in the end into which the bolt can be screwed.

It is the bolt that will hold the blade of the electric jigsaw. To drill a hole in the end of the bolt, you will have to use a drill of a suitable diameter, and to cut threads, a tool such as a tap.

LiveInternetLiveInternet

Let's transfer it to calico, I stitch it on a sewing machine, and then cut it out, you can do it as you like

Leave a hole for turning. Before turning, we make notches on the seam allowances so that creases do not form on the finished product.

We fill the blanks with padding polyester, holofiber, whatever you have at hand. Let’s leave our preparations and proceed to the base, on which all this beauty will be attached.

To do this, if there is no suitable box or board, take two packs of cigarettes, take out the insides and remove the lids, fill them halfway with cereal (I took millet), you can take anything as a weighting agent. We lay padding polyester on top so that the cereal does not fall out. It should look something like this

Only both packs should be filled evenly, that is, have a weighting material at the bottom and padding polyester on top of it. Next, we insert one pack into another and strengthen them with tape or self-adhesive paper to create a solid platform.

We wrap the box first with padding polyester, then with calico. It can be hemmed by hand or glued onto the web using an iron.

We sew the finished platform with our blank according to the principle of sewing a tilde snail.

That's all, all that's left is to paint it with a solution of coffee, cinnamon, vanillin and PVA.

Dry, decorate with braid, paint or decoupage the fabric. (Eden Kogan has a master class). I made two pincushions so that I would always have them on hand when I sew. I hung the heart on a sewing machine.

In general, use your imagination and you will succeed))) Good luck!

2 MK. Sewing machine for Tilda

To sew such a sewing machine you will need:

• scraps of fabric (small),
• filler,
• cardboard,
• 2 wooden toothpicks,
• threads,
• glue,
• flat button.

Pattern

I drew it while looking at photos of old Singer machines. The pattern shows the dimensions of my machine.

We cut out the parts of the machine - the machine itself and the stand, 2 parts each with seam allowances of 3-5 mm. We sew, the width of the seam should not be made too small. Don't forget about the holes for turning out:

Turn it inside out and straighten it out. We stuff the machine part, and insert padding polyester into the stand and maybe cardboard for the mold. Take a toothpick. We break off part of the toothpick and stick the non-sharp end into the machine, directly into the seam where the needle was. This will be our needle. Its length can be adjusted later:

We also make a coil for the machine using a toothpick, putting 2 small cardboard circles on it and securing them with a drop of glue.

We wind the thread between the circles. The size of the coils, of course, should be small:

Now we insert this coil into the machine (into the seam), after dripping glue onto the tip of the toothpick. We place the machine on the stand and sew it with a hidden seam. We adjust the length of the “needle” and also secure it with a drop of glue.

We will make the flywheel from an ordinary flat button of a suitable size. Let's cut out 2 cardboard circles according to the size of the button (one is the same size, the second is slightly smaller), and cover them with fabric (using the yo-yoshka principle):

Glue the smaller circle to the button on one side (concave side):

Glue a larger circle on the back side of the button (more convex, curved):

After the glue has completely dried, we sew the resulting “flywheel” to the machine:

The car is ready. You can place a piece of fabric under the needle. A little trick: to prevent the needle from moving around the stand, you can sew a small button and fix the tip of the toothpick-needle into the hole of the button:

The car can be “given into the hands” of interior dolls, which is what I did:

But it can also be used as a small pincushion.

3. ANOTHER PATTERN

4.EXAMPLES.

BEAUTIFUL NEEDLE CASES AND A JOYFUL MOOD TO ALL!